Fortinet NSE5_FSW_AD-7.6 (Fortinet NSE 5 - FortiSwitch 7.6 Administrator) Practice Test 50

Question 490

When engineers apply a port security profile to a FortiSwitch interface at the lab, which forwarding, security, management or diagnostic outcome follows from that action?

  1. MAC-based mode maintains per-device authorization decisions instead of granting the entire port one common state
  2. A port policy binds appropriate authentication and security settings to an interface
  3. TTLS wraps inner authentication within a protected tunnel and requires matching endpoint/server settings
  4. An unauthorized or guest network can provide limited connectivity instead of normal production access

Explanation

Correct Answer

B:

Given the described goal, the configured operation is meant to maintain a reusable set of network admission controls on selected access ports. The most relevant validation is to inspect applied port policy identity and active session state for the equipment at the lab.

Incorrect Answers

A:

That behavior applies when engineers “Use MAC-based 802.1X access sessions”; the different operation “Apply a port security profile to a FortiSwitch interface” is intended to maintain a reusable set of network admission controls on selected access ports. That different feature is verified by inspect individual authenticated MAC session entries on the interface; for “Apply a port security profile to a FortiSwitch interface” on an access switch in routine maintenance, the relevant evidence is to inspect applied port policy identity and active session state.

C:

This outcome would be relevant to “Use EAP-TTLS for compatible tunnel-based access authentication” at the lab, not the task “Apply a port security profile to a FortiSwitch interface”; the other task is to provide a tunneled credential exchange supported by the configured RADIUS server. The action “Apply a port security profile to a FortiSwitch interface” targets a different result: a port policy binds appropriate authentication and security settings to an interface; the proposed alternative would instead be checked by inspect the negotiated EAP type in the access attempt.

D:

That behavior applies when engineers “Use a guest or unauthorized VLAN policy where supported”; the different operation “Apply a port security profile to a FortiSwitch interface” is intended to maintain a reusable set of network admission controls on selected access ports. That different feature is verified by inspect the failed authentication state and assigned VLAN on the endpoint session; for “Apply a port security profile to a FortiSwitch interface” on an access switch in routine maintenance, the relevant evidence is to inspect applied port policy identity and active session state.

Question 491

A technician says “Apply a port security profile to a FortiSwitch interface” has solved the issue at the staging rack. Which diagnostic step would substantiate that claim?

  1. Trace the RADIUS path and examine the matching FortiGate policy hit counters
  2. Inspect individual authenticated MAC session entries on the interface
  3. Compare RADIUS accounting entries with the switch's active sessions
  4. Inspect applied port policy identity and active session state

Explanation

Correct Answer

D:

The switch behavior that matters is: a port policy binds appropriate authentication and security settings to an interface. Directly measuring that result demonstrates whether the step to maintain a reusable set of network admission controls on selected access ports succeeded on a managed campus switch.

Incorrect Answers

A:

The proposed check concerns “Permit RADIUS traffic from managed FortiSwitch via FortiGate” rather than “Apply a port security profile to a FortiSwitch interface”: a managed FortiSwitch often needs an explicit FortiGate firewall policy permitting RADIUS flow from FortiLink. For “Apply a port security profile to a FortiSwitch interface” on a managed campus switch, a better test would be to inspect applied port policy identity and active session state, which targets maintain a reusable set of network admission controls on selected access ports rather than the alternative diagnostic “Permit RADIUS traffic from managed FortiSwitch via FortiGate”.

B:

This check is suited to “Use MAC-based 802.1X access sessions” when trying to control separate endpoint identities on one shared physical port, not to verify “Apply a port security profile to a FortiSwitch interface” at the staging rack. Checking “Apply a port security profile to a FortiSwitch interface” at the staging rack requires evidence of its own mechanism: a port policy binds appropriate authentication and security settings to an interface; that is not the outcome measured by “Use MAC-based 802.1X access sessions”.

C:

This check is suited to “Enable RADIUS accounting for access sessions” when trying to record network access session starts and stops outside the switch, not to verify “Apply a port security profile to a FortiSwitch interface” at the staging rack. Checking “Apply a port security profile to a FortiSwitch interface” at the staging rack requires evidence of its own mechanism: a port policy binds appropriate authentication and security settings to an interface; that is not the outcome measured by “Enable RADIUS accounting for access sessions”.

Question 492

A deployment review at the research building identifies this objective: restrict how many endpoint MAC addresses an access interface can learn. Which FortiSwitch operation should be selected?

  1. Enable RADIUS accounting for access sessions
  2. Configure MAC address learning limits
  3. Permit RADIUS traffic from managed FortiSwitch via FortiGate
  4. Provision device MAC identities in RADIUS for MAB

Explanation

Correct Answer

B:

At this network boundary, MAC learning limits cap layer-2 learned identities rather than validating EAP or DHCP leases. The operator can test this claim by the specific check: check learned-MAC counts and violations against the configured limit.

Incorrect Answers

A:

Compared with the requested “Configure MAC address learning limits” at the research building, this would record network access session starts and stops outside the switch instead: accounting sends session records to a collector distinct from the basic allow-or-deny authentication result. At the research building, the operational proof would instead be to check learned-MAC counts and violations against the configured limit, whereas “Enable RADIUS accounting for access sessions” is validated by a different test: compare RADIUS accounting entries with the switch's active sessions.

C:

For the research building, “Permit RADIUS traffic from managed FortiSwitch via FortiGate” is a different type of control from “Configure MAC address learning limits”: a managed FortiSwitch often needs an explicit FortiGate firewall policy permitting RADIUS flow from FortiLink. Unlike the requested feature, that setting addresses the need to restore network authentication when the switch cannot reach a remote RADIUS server, not the objective to restrict how many endpoint MAC addresses an access interface can learn.

D:

Compared with the requested “Configure MAC address learning limits” at the research building, this would make network devices without certificates recognizable to the access policy instead: MAB needs a server-side record or lookup logic that accepts the enrolled MAC identities. At the research building, the operational proof would instead be to check learned-MAC counts and violations against the configured limit, whereas “Provision device MAC identities in RADIUS for MAB” is validated by a different test: search RADIUS logs for the submitted hardware address and expected accept decision.

Question 493

A colleague asks about the effect of “Configure MAC address learning limits” on a FortiLink-managed access switch. Which behavior best characterizes that feature?

  1. A configured MAC identity restricts layer-2 admission or learning to designated devices
  2. MAB needs a server-side record or lookup logic that accepts the enrolled MAC identities
  3. Accounting sends session records to a collector distinct from the basic allow-or-deny authentication result
  4. MAC learning limits cap layer-2 learned identities rather than validating EAP or DHCP leases
  5. 802.1X uses EAP between the endpoint and the switch authenticator, with RADIUS decision-making upstream

Explanation

Correct Answer

D:

In this deployment, the configured operation is meant to restrict how many endpoint MAC addresses an access interface can learn. The most relevant validation is to check learned-MAC counts and violations against the configured limit for the equipment at the airport office.

Incorrect Answers

A:

That behavior applies when engineers “Use static MAC security for a fixed appliance”; the different operation “Configure MAC address learning limits” is intended to restrict how many endpoint MAC addresses an access interface can learn. That different feature is verified by check the secure MAC table and the source address of blocked frames; for “Configure MAC address learning limits” on a FortiLink-managed access switch, the relevant evidence is to check learned-MAC counts and violations against the configured limit.

B:

That behavior applies when engineers “Provision device MAC identities in RADIUS for MAB”; the different operation “Configure MAC address learning limits” is intended to restrict how many endpoint MAC addresses an access interface can learn. That different feature is verified by search RADIUS logs for the submitted hardware address and expected accept decision; for “Configure MAC address learning limits” on a FortiLink-managed access switch, the relevant evidence is to check learned-MAC counts and violations against the configured limit.

C:

That behavior applies when engineers “Enable RADIUS accounting for access sessions”; the different operation “Configure MAC address learning limits” is intended to restrict how many endpoint MAC addresses an access interface can learn. That different feature is verified by compare RADIUS accounting entries with the switch's active sessions; for “Configure MAC address learning limits” on a FortiLink-managed access switch, the relevant evidence is to check learned-MAC counts and violations against the configured limit.

E:

This outcome would be relevant to “Configure 802.1X for a user-facing port” at the airport office, not the task “Configure MAC address learning limits”; the other task is to authenticate a standards-compliant supplicant before admitting it to the access network. The action “Configure MAC address learning limits” targets a different result: MAC learning limits cap layer-2 learned identities rather than validating EAP or DHCP leases; the proposed alternative would instead be checked by inspect the 802.1X session state and RADIUS accept or reject result.

Question 494

After the team configures “Configure MAC address learning limits” on a switch linked to a FortiGate running FortiOS 7.6, which TWO claims about the configuration are valid? (Choose TWO.)

  1. PEAP establishes a protected authentication exchange; it remains distinct from MAB and switch MAC limits
  2. A configured MAC identity restricts layer-2 admission or learning to designated devices
  3. MAC learning limits cap layer-2 learned identities rather than validating EAP or DHCP leases
  4. Check learned-MAC counts and violations against the configured limit
  5. Port-based access control gates the entire port, which matters if multiple devices share the same physical connection

Explanation

Correct Answers

C:

For the stated requirement, the described mechanism corresponds to the operation that administrators use to restrict how many endpoint MAC addresses an access interface can learn. The result should be observable on a switch linked to a FortiGate running FortiOS 7.6.

D:

The stated check directly tests whether the intended function is active at the operations center. It provides evidence about “Configure MAC address learning limits” beyond ordinary link-up state on a switch linked to a FortiGate running FortiOS 7.6.

Incorrect Answers

A:

That characteristic reflects “Use EAP-PEAP where the RADIUS design requires a protected inner method” rather than “Configure MAC address learning limits” at the operations center. Its actual role is to support a tunneled EAP authentication approach for compatible endpoints, a different configuration need.

B:

That characteristic reflects “Use static MAC security for a fixed appliance” rather than “Configure MAC address learning limits” at the operations center. Its actual role is to allow a particular known device address on a controlled interface, a different configuration need.

E:

That characteristic reflects “Use port-based 802.1X authorization” rather than “Configure MAC address learning limits” at the operations center. Its actual role is to treat the interface as authorized after a permitted port-level authentication succeeds, a different configuration need.

Question 495

A peer review of the warehouse asks how the design will allow a particular known device address on a controlled interface. Which FortiSwitch technique is the correct response?

  1. Configure 802.1X for a user-facing port
  2. Use EAP-PEAP where the RADIUS design requires a protected inner method
  3. Use static MAC security for a fixed appliance
  4. Configure MAC address learning limits

Explanation

Correct Answer

C:

The deciding detail is that a configured MAC identity restricts layer-2 admission or learning to designated devices. This distinction is material to the warehouse, where the stated goal is to allow a particular known device address on a controlled interface.

Incorrect Answers

A:

For the warehouse, “Configure 802.1X for a user-facing port” is a different type of control from “Use static MAC security for a fixed appliance”: 802.1X uses EAP between the endpoint and the switch authenticator, with RADIUS decision-making upstream. Unlike the requested feature, that setting addresses the need to authenticate a standards-compliant supplicant before admitting it to the access network, not the objective to allow a particular known device address on a controlled interface.

B:

Compared with the requested “Use static MAC security for a fixed appliance” at the warehouse, this would support a tunneled EAP authentication approach for compatible endpoints instead: PEAP establishes a protected authentication exchange; it remains distinct from MAB and switch MAC limits. At the warehouse, the operational proof would instead be to check the secure MAC table and the source address of blocked frames, whereas “Use EAP-PEAP where the RADIUS design requires a protected inner method” is validated by a different test: inspect client EAP type and server-side PEAP negotiation events.

D:

Compared with the requested “Use static MAC security for a fixed appliance” at the warehouse, this would restrict how many endpoint MAC addresses an access interface can learn instead: MAC learning limits cap layer-2 learned identities rather than validating EAP or DHCP leases. At the warehouse, the operational proof would instead be to check the secure MAC table and the source address of blocked frames, whereas “Configure MAC address learning limits” is validated by a different test: check learned-MAC counts and violations against the configured limit.

Question 496

During validation of a FortiSwitch connected to the security edge at the headquarters, the team asks what the change “Use static MAC security for a fixed appliance” actually does. Which outcome is correct?

  1. A configured MAC identity restricts layer-2 admission or learning to designated devices
  2. Port-based access control gates the entire port, which matters if multiple devices share the same physical connection
  3. An 802.1X-capable client must participate in EAPOL before the server can approve its credentials
  4. MAC learning limits cap layer-2 learned identities rather than validating EAP or DHCP leases
  5. PEAP establishes a protected authentication exchange; it remains distinct from MAB and switch MAC limits

Explanation

Correct Answer

A:

The relevant mechanism is: the configured operation is meant to allow a particular known device address on a controlled interface. The most relevant validation is to check the secure MAC table and the source address of blocked frames for the equipment at the headquarters.

Incorrect Answers

B:

This outcome would be relevant to “Use port-based 802.1X authorization” at the headquarters, not the task “Use static MAC security for a fixed appliance”; the other task is to treat the interface as authorized after a permitted port-level authentication succeeds. The action “Use static MAC security for a fixed appliance” targets a different result: a configured MAC identity restricts layer-2 admission or learning to designated devices; the proposed alternative would instead be checked by inspect authorized port state and evaluate behavior of hosts behind that port.

C:

That behavior applies when engineers “Troubleshoot an 802.1X supplicant that never starts”; the different operation “Use static MAC security for a fixed appliance” is intended to allow a particular known device address on a controlled interface. That different feature is verified by capture EAPOL frames on the access port and inspect endpoint supplicant state; for “Use static MAC security for a fixed appliance” on a FortiSwitch connected to the security edge, the relevant evidence is to check the secure MAC table and the source address of blocked frames.

D:

That behavior applies when engineers “Configure MAC address learning limits”; the different operation “Use static MAC security for a fixed appliance” is intended to allow a particular known device address on a controlled interface. That different feature is verified by check learned-MAC counts and violations against the configured limit; for “Use static MAC security for a fixed appliance” on a FortiSwitch connected to the security edge, the relevant evidence is to check the secure MAC table and the source address of blocked frames.

E:

That behavior applies when engineers “Use EAP-PEAP where the RADIUS design requires a protected inner method”; the different operation “Use static MAC security for a fixed appliance” is intended to allow a particular known device address on a controlled interface. That different feature is verified by inspect client EAP type and server-side PEAP negotiation events; for “Use static MAC security for a fixed appliance” on a FortiSwitch connected to the security edge, the relevant evidence is to check the secure MAC table and the source address of blocked frames.

Question 497

The change-control ticket for an access switch in routine maintenance requires one validation of the goal to allow a particular known device address on a controlled interface. Which evidence should be collected?

  1. Check the MAC-based RADIUS transaction and device session authorization
  2. Capture EAPOL frames on the access port and inspect endpoint supplicant state
  3. Inspect the CoA transaction and subsequent session policy or VLAN state
  4. Check the secure MAC table and the source address of blocked frames

Explanation

Correct Answer

D:

This approach fits because a configured MAC identity restricts layer-2 admission or learning to designated devices. Directly measuring that result demonstrates whether the step to allow a particular known device address on a controlled interface succeeded on an access switch in routine maintenance.

Incorrect Answers

A:

This check is suited to “Enable MAC authentication bypass for a legacy camera” when trying to admit a non-802.1X device through a controlled RADIUS identity check, not to verify “Use static MAC security for a fixed appliance” at the hospital wing. Checking “Use static MAC security for a fixed appliance” at the hospital wing requires evidence of its own mechanism: a configured MAC identity restricts layer-2 admission or learning to designated devices; that is not the outcome measured by “Enable MAC authentication bypass for a legacy camera”.

B:

This check is suited to “Troubleshoot an 802.1X supplicant that never starts” when trying to determine why a locked port sees no usable EAP exchange from the attached device, not to verify “Use static MAC security for a fixed appliance” at the hospital wing. Checking “Use static MAC security for a fixed appliance” at the hospital wing requires evidence of its own mechanism: a configured MAC identity restricts layer-2 admission or learning to designated devices; that is not the outcome measured by “Troubleshoot an 802.1X supplicant that never starts”.

C:

The proposed check concerns “Use RADIUS change of authorization where supported” rather than “Use static MAC security for a fixed appliance”: a RADIUS CoA message can alter an established authorization in a supported policy workflow. For “Use static MAC security for a fixed appliance” on an access switch in routine maintenance, a better test would be to check the secure MAC table and the source address of blocked frames, which targets allow a particular known device address on a controlled interface rather than the alternative diagnostic “Use RADIUS change of authorization where supported”.

Question 498

A production incident in the training center reveals the need to separate endpoints that have not completed approved network authentication. Which targeted FortiSwitch setting or method should the team use?

  1. Enable MAC authentication bypass for a legacy camera
  2. Use a guest or unauthorized VLAN policy where supported
  3. Clear a stale 802.1X authorized session during diagnostics
  4. Apply a port security profile to a FortiSwitch interface

Explanation

Correct Answer

B:

The critical distinction is that an unauthorized or guest network can provide limited connectivity instead of normal production access. The operator can test this claim by the specific check: inspect the failed authentication state and assigned VLAN on the endpoint session.

Incorrect Answers

A:

For the training center, “Enable MAC authentication bypass for a legacy camera” is a different type of control from “Use a guest or unauthorized VLAN policy where supported”: MAB can submit a device MAC address as authentication credentials when no EAP supplicant is available. Unlike the requested feature, that setting addresses the need to admit a non-802.1X device through a controlled RADIUS identity check, not the objective to separate endpoints that have not completed approved network authentication.

C:

Compared with the requested “Use a guest or unauthorized VLAN policy where supported” at the training center, this would force reauthentication after the endpoint or authorization rule has changed instead: session clearing removes prior authorization state so that a fresh EAP/RADIUS exchange can be assessed. At the training center, the operational proof would instead be to inspect the failed authentication state and assigned VLAN on the endpoint session, whereas “Clear a stale 802.1X authorized session during diagnostics” is validated by a different test: inspect the session table before and after clearing and review the new authentication exchange.

D:

Compared with the requested “Use a guest or unauthorized VLAN policy where supported” at the training center, this would maintain a reusable set of network admission controls on selected access ports instead: a port policy binds appropriate authentication and security settings to an interface. At the training center, the operational proof would instead be to inspect the failed authentication state and assigned VLAN on the endpoint session, whereas “Apply a port security profile to a FortiSwitch interface” is validated by a different test: inspect applied port policy identity and active session state.

Question 499

Before applying the planned operation “Use a guest or unauthorized VLAN policy where supported” at the lab, the administrator must predict its impact. Which prediction is sound?

  1. An unauthorized or guest network can provide limited connectivity instead of normal production access
  2. EAP-TLS uses certificate validation in the authentication flow rather than a simple MAC-only identity
  3. The switch forwards authentication exchanges to a configured RADIUS service rather than validating enterprise credentials by itself
  4. A port policy binds appropriate authentication and security settings to an interface

Explanation

Correct Answer

A:

That setting is appropriate here because the configured operation is meant to separate endpoints that have not completed approved network authentication. The most relevant validation is to inspect the failed authentication state and assigned VLAN on the endpoint session for the equipment at the lab.

Incorrect Answers

B:

This outcome would be relevant to “Use EAP-TLS where device certificates are deployed” at the lab, not the task “Use a guest or unauthorized VLAN policy where supported”; the other task is to authenticate compliant devices with a certificate-based EAP exchange. The action “Use a guest or unauthorized VLAN policy where supported” targets a different result: an unauthorized or guest network can provide limited connectivity instead of normal production access; the proposed alternative would instead be checked by examine EAP-TLS negotiation and server certificate trust results.

C:

That behavior applies when engineers “Configure a reachable RADIUS authentication server”; the different operation “Use a guest or unauthorized VLAN policy where supported” is intended to separate endpoints that have not completed approved network authentication. That different feature is verified by test RADIUS reachability, shared-secret agreement and server response time; for “Use a guest or unauthorized VLAN policy where supported” on a recently upgraded FortiSwitch, the relevant evidence is to inspect the failed authentication state and assigned VLAN on the endpoint session.

D:

That behavior applies when engineers “Apply a port security profile to a FortiSwitch interface”; the different operation “Use a guest or unauthorized VLAN policy where supported” is intended to separate endpoints that have not completed approved network authentication. That different feature is verified by inspect applied port policy identity and active session state; for “Use a guest or unauthorized VLAN policy where supported” on a recently upgraded FortiSwitch, the relevant evidence is to inspect the failed authentication state and assigned VLAN on the endpoint session.

Question 500

A FortiSwitch engineer in the media studio is documenting successful operation of “Use a guest or unauthorized VLAN policy where supported.” Which measurement or inspection confirms it?

  1. Examine EAP-TLS negotiation and server certificate trust results
  2. Inspect the failed authentication state and assigned VLAN on the endpoint session
  3. Inspect the negotiated EAP type in the access attempt
  4. Test RADIUS reachability, shared-secret agreement and server response time
  5. Check the secure MAC table and the source address of blocked frames

Explanation

Correct Answer

B:

This is the precise control because an unauthorized or guest network can provide limited connectivity instead of normal production access. Directly measuring that result demonstrates whether the step to separate endpoints that have not completed approved network authentication succeeded on a FortiLink-managed access switch.

Incorrect Answers

A:

The proposed check concerns “Use EAP-TLS where device certificates are deployed” rather than “Use a guest or unauthorized VLAN policy where supported”: EAP-TLS uses certificate validation in the authentication flow rather than a simple MAC-only identity. For “Use a guest or unauthorized VLAN policy where supported” on a FortiLink-managed access switch, a better test would be to inspect the failed authentication state and assigned VLAN on the endpoint session, which targets separate endpoints that have not completed approved network authentication rather than the alternative diagnostic “Use EAP-TLS where device certificates are deployed”.

C:

This check is suited to “Use EAP-TTLS for compatible tunnel-based access authentication” when trying to provide a tunneled credential exchange supported by the configured RADIUS server, not to verify “Use a guest or unauthorized VLAN policy where supported” at the media studio. Checking “Use a guest or unauthorized VLAN policy where supported” at the media studio requires evidence of its own mechanism: an unauthorized or guest network can provide limited connectivity instead of normal production access; that is not the outcome measured by “Use EAP-TTLS for compatible tunnel-based access authentication”.

D:

This check is suited to “Configure a reachable RADIUS authentication server” when trying to provide external identity validation for network access control, not to verify “Use a guest or unauthorized VLAN policy where supported” at the media studio. Checking “Use a guest or unauthorized VLAN policy where supported” at the media studio requires evidence of its own mechanism: an unauthorized or guest network can provide limited connectivity instead of normal production access; that is not the outcome measured by “Configure a reachable RADIUS authentication server”.

E:

The proposed check concerns “Use static MAC security for a fixed appliance” rather than “Use a guest or unauthorized VLAN policy where supported”: a configured MAC identity restricts layer-2 admission or learning to designated devices. For “Use a guest or unauthorized VLAN policy where supported” on a FortiLink-managed access switch, a better test would be to inspect the failed authentication state and assigned VLAN on the endpoint session, which targets separate endpoints that have not completed approved network authentication rather than the alternative diagnostic “Use static MAC security for a fixed appliance”.

Fortinet NSE 5 - FortiSwitch 7.6 Administrator (NSE5_FSW_AD-7.6) Practice Tests