Fortinet NSE5_FSW_AD-7.6 (Fortinet NSE 5 - FortiSwitch 7.6 Administrator) Practice Test 60

Question 590

At the airport office, a dashboard shows ordinary link-up state, but the team also needs proof for “Match an ACL using an IP subnet.” Which targeted check should be used?

  1. Inspect policer conformance/excess statistics alongside ACL counters
  2. Compare the source MAC with the VLAN-assignment entry and effective port VLAN membership
  3. Test server-to-gateway reachability and server-to-server isolation within the isolated VLAN
  4. Compare captured source/destination IP fields and the rule's mask

Explanation

Correct Answer

D:

For the stated requirement, an IP source or destination prefix classifier restricts the match to packets meeting the configured address condition. Directly measuring that result demonstrates whether the step to filter traffic from a designated routed network range succeeded on a switch linked to a FortiGate running FortiOS 7.6.

Incorrect Answers

A:

This check is suited to “Apply an ACL policer to matching frames” when trying to rate-control selected traffic rather than dropping every matching packet, not to verify “Match an ACL using an IP subnet” at the airport office. Checking “Match an ACL using an IP subnet” at the airport office requires evidence of its own mechanism: an IP source or destination prefix classifier restricts the match to packets meeting the configured address condition; that is not the outcome measured by “Apply an ACL policer to matching frames”.

B:

This check is suited to “Use a MAC-based VLAN security association” when trying to keep a known endpoint's traffic on an assigned segment when moved among permitted ports, not to verify “Match an ACL using an IP subnet” at the airport office. Checking “Match an ACL using an IP subnet” at the airport office requires evidence of its own mechanism: an IP source or destination prefix classifier restricts the match to packets meeting the configured address condition; that is not the outcome measured by “Use a MAC-based VLAN security association”.

C:

The proposed check concerns “Apply an isolated secondary PVLAN for tenant servers” rather than “Match an ACL using an IP subnet”: isolated PVLAN ports can reach the promiscuous primary attachment but not one another. For “Match an ACL using an IP subnet” on a switch linked to a FortiGate running FortiOS 7.6, a better test would be to compare captured source/destination IP fields and the rule's mask, which targets filter traffic from a designated routed network range rather than the alternative diagnostic “Apply an isolated secondary PVLAN for tenant servers”.

Question 591

At the conference venue, a technician is choosing between several switching features to separate IPv4, IPv6 or other Ethernet frame types in a hardware policy. Which one belongs in the implementation plan?

  1. Use an ACL Ethernet-type classifier
  2. Apply an ACL policer to matching frames
  3. Use a MAC-based VLAN security association
  4. Apply an isolated secondary PVLAN for tenant servers

Explanation

Correct Answer

A:

The deciding detail is that an EtherType comparison identifies the payload protocol without relying on TCP/UDP port numbers. This distinction is material to the conference venue, where the stated goal is to separate IPv4, IPv6 or other Ethernet frame types in a hardware policy.

Incorrect Answers

B:

Compared with the requested “Use an ACL Ethernet-type classifier” at the conference venue, this would rate-control selected traffic rather than dropping every matching packet instead: a linked policer enforces meter behavior for the matched ACL class. At the conference venue, the operational proof would instead be to read the EtherType from the frame header and inspect the ACL service match, whereas “Apply an ACL policer to matching frames” is validated by a different test: inspect policer conformance/excess statistics alongside ACL counters.

C:

For the conference venue, “Use a MAC-based VLAN security association” is a different type of control from “Use an ACL Ethernet-type classifier”: MAC-to-VLAN mapping is based on source identity and differs from general ACL drop actions. Unlike the requested feature, that setting addresses the need to keep a known endpoint's traffic on an assigned segment when moved among permitted ports, not the objective to separate IPv4, IPv6 or other Ethernet frame types in a hardware policy.

D:

Compared with the requested “Use an ACL Ethernet-type classifier” at the conference venue, this would allow server access to a shared gateway while blocking any host-to-host communication instead: isolated PVLAN ports can reach the promiscuous primary attachment but not one another. At the conference venue, the operational proof would instead be to read the EtherType from the frame header and inspect the ACL service match, whereas “Apply an isolated secondary PVLAN for tenant servers” is validated by a different test: test server-to-gateway reachability and server-to-server isolation within the isolated VLAN.

Question 592

Before applying the planned operation “Use an ACL Ethernet-type classifier” at the campus, the administrator must predict its impact. Which prediction is sound?

  1. ACL actions can assign supported classification or priority treatment to matching frames
  2. The promiscuous port connects secondary VLANs to the common routed or shared service endpoint
  3. For conflicting group actions, the lower-numbered ACL group has higher action priority
  4. An EtherType comparison identifies the payload protocol without relying on TCP/UDP port numbers
  5. An ingress ACL classifies traffic arriving at an interface and applies permitted hardware actions

Explanation

Correct Answer

D:

The relevant mechanism is: the configured operation is meant to separate IPv4, IPv6 or other Ethernet frame types in a hardware policy. The most relevant validation is to read the EtherType from the frame header and inspect the ACL service match for the equipment at the campus.

Incorrect Answers

A:

That behavior applies when engineers “Apply a QoS action using an ACL”; the different operation “Use an ACL Ethernet-type classifier” is intended to separate IPv4, IPv6 or other Ethernet frame types in a hardware policy. That different feature is verified by inspect ACL match counters and resulting QoS queue handling; for “Use an ACL Ethernet-type classifier” on a managed switch running FortiSwitchOS 7.6, the relevant evidence is to read the EtherType from the frame header and inspect the ACL service match.

B:

That behavior applies when engineers “Configure a promiscuous PVLAN port for a shared gateway”; the different operation “Use an ACL Ethernet-type classifier” is intended to separate IPv4, IPv6 or other Ethernet frame types in a hardware policy. That different feature is verified by inspect gateway reachability from each secondary VLAN without direct host-to-host communication; for “Use an ACL Ethernet-type classifier” on a managed switch running FortiSwitchOS 7.6, the relevant evidence is to read the EtherType from the frame header and inspect the ACL service match.

C:

That behavior applies when engineers “Keep ACL group priority ordering consistent”; the different operation “Use an ACL Ethernet-type classifier” is intended to separate IPv4, IPv6 or other Ethernet frame types in a hardware policy. That different feature is verified by inspect matching rules by ACL group and compare their group numbers; for “Use an ACL Ethernet-type classifier” on a managed switch running FortiSwitchOS 7.6, the relevant evidence is to read the EtherType from the frame header and inspect the ACL service match.

E:

This outcome would be relevant to “Install an ingress ACL for received traffic” at the campus, not the task “Use an ACL Ethernet-type classifier”; the other task is to filter packets as they enter a FortiSwitch forwarding pipeline. The action “Use an ACL Ethernet-type classifier” targets a different result: an EtherType comparison identifies the payload protocol without relying on TCP/UDP port numbers; the proposed alternative would instead be checked by review ingress ACL match counters while sending matching test frames.

Question 593

The change-control ticket for a remote FortiSwitch installation requires one validation of the goal to separate IPv4, IPv6 or other Ethernet frame types in a hardware policy. Which evidence should be collected?

  1. Test peer reachability inside the community and deny a connection to a different community
  2. Read the EtherType from the frame header and inspect the ACL service match
  3. Check prelookup stage configuration and rule-use counters
  4. Confirm matching test packets are counted and discarded while unrelated traffic still passes

Explanation

Correct Answer

B:

This approach fits because an EtherType comparison identifies the payload protocol without relying on TCP/UDP port numbers. Directly measuring that result demonstrates whether the step to separate IPv4, IPv6 or other Ethernet frame types in a hardware policy succeeded on a remote FortiSwitch installation.

Incorrect Answers

A:

This check is suited to “Apply a community secondary PVLAN to one workgroup” when trying to allow peers within one designated group to communicate but isolate them from other groups, not to verify “Use an ACL Ethernet-type classifier” at the remote depot. Checking “Use an ACL Ethernet-type classifier” at the remote depot requires evidence of its own mechanism: an EtherType comparison identifies the payload protocol without relying on TCP/UDP port numbers; that is not the outcome measured by “Apply a community secondary PVLAN to one workgroup”.

C:

This check is suited to “Use prelookup ACL classification” when trying to match traffic in an early processing stage before subsequent forwarding decisions, not to verify “Use an ACL Ethernet-type classifier” at the remote depot. Checking “Use an ACL Ethernet-type classifier” at the remote depot requires evidence of its own mechanism: an EtherType comparison identifies the payload protocol without relying on TCP/UDP port numbers; that is not the outcome measured by “Use prelookup ACL classification”.

D:

The proposed check concerns “Drop matched unwanted frames with an ACL action” rather than “Use an ACL Ethernet-type classifier”: a drop action discards frames meeting the ACL match rather than disabling the whole physical port. For “Use an ACL Ethernet-type classifier” on a remote FortiSwitch installation, a better test would be to read the EtherType from the frame header and inspect the ACL service match, which targets separate IPv4, IPv6 or other Ethernet frame types in a hardware policy rather than the alternative diagnostic “Drop matched unwanted frames with an ACL action”.

Question 594

The accepted design for the branch office requires the ability to prioritize a defined class without requiring every endpoint to mark itself. Which switch feature is the closest fit?

  1. Apply a community secondary PVLAN to one workgroup
  2. Apply a QoS action using an ACL
  3. Match an ACL using an IP subnet
  4. Review the ACL hardware resource usage

Explanation

Correct Answer

B:

The critical distinction is that ACL actions can assign supported classification or priority treatment to matching frames. The operator can test this claim by the specific check: inspect ACL match counters and resulting QoS queue handling.

Incorrect Answers

A:

Compared with the requested “Apply a QoS action using an ACL” at the branch office, this would allow peers within one designated group to communicate but isolate them from other groups instead: community PVLAN members can communicate with their own community and the promiscuous primary port. At the branch office, the operational proof would instead be to inspect ACL match counters and resulting QoS queue handling, whereas “Apply a community secondary PVLAN to one workgroup” is validated by a different test: test peer reachability inside the community and deny a connection to a different community.

C:

For the branch office, “Match an ACL using an IP subnet” is a different type of control from “Apply a QoS action using an ACL”: an IP source or destination prefix classifier restricts the match to packets meeting the configured address condition. Unlike the requested feature, that setting addresses the need to filter traffic from a designated routed network range, not the objective to prioritize a defined class without requiring every endpoint to mark itself.

D:

Compared with the requested “Apply a QoS action using an ACL” at the branch office, this would diagnose rejection of additional switch ACL entries despite apparently valid syntax instead: switch ACL classifiers, groups and counters consume finite hardware resources that can be fragmented. At the branch office, the operational proof would instead be to inspect ACL match counters and resulting QoS queue handling, whereas “Review the ACL hardware resource usage” is validated by a different test: inspect ACL usage and available hardware entries before changing rule order.

Question 595

During validation of a standalone FortiSwitch appliance at the factory, the team asks what the change “Apply a QoS action using an ACL” actually does. Which outcome is correct?

  1. ACL actions can assign supported classification or priority treatment to matching frames
  2. Isolated PVLAN ports can reach the promiscuous primary attachment but not one another
  3. MAC-to-VLAN mapping is based on source identity and differs from general ACL drop actions
  4. A linked policer enforces meter behavior for the matched ACL class
  5. An egress-stage policy acts on frames being transmitted rather than their original entry classification

Explanation

Correct Answer

A:

That setting is appropriate here because the configured operation is meant to prioritize a defined class without requiring every endpoint to mark itself. The most relevant validation is to inspect ACL match counters and resulting QoS queue handling for the equipment at the factory.

Incorrect Answers

B:

That behavior applies when engineers “Apply an isolated secondary PVLAN for tenant servers”; the different operation “Apply a QoS action using an ACL” is intended to prioritize a defined class without requiring every endpoint to mark itself. That different feature is verified by test server-to-gateway reachability and server-to-server isolation within the isolated VLAN; for “Apply a QoS action using an ACL” on a standalone FortiSwitch appliance, the relevant evidence is to inspect ACL match counters and resulting QoS queue handling.

C:

That behavior applies when engineers “Use a MAC-based VLAN security association”; the different operation “Apply a QoS action using an ACL” is intended to prioritize a defined class without requiring every endpoint to mark itself. That different feature is verified by compare the source MAC with the VLAN-assignment entry and effective port VLAN membership; for “Apply a QoS action using an ACL” on a standalone FortiSwitch appliance, the relevant evidence is to inspect ACL match counters and resulting QoS queue handling.

D:

This outcome would be relevant to “Apply an ACL policer to matching frames” at the factory, not the task “Apply a QoS action using an ACL”; the other task is to rate-control selected traffic rather than dropping every matching packet. The action “Apply a QoS action using an ACL” targets a different result: ACL actions can assign supported classification or priority treatment to matching frames; the proposed alternative would instead be checked by inspect policer conformance/excess statistics alongside ACL counters.

E:

That behavior applies when engineers “Install an egress ACL for outgoing traffic”; the different operation “Apply a QoS action using an ACL” is intended to prioritize a defined class without requiring every endpoint to mark itself. That different feature is verified by inspect egress ACL counters for the relevant outgoing port; for “Apply a QoS action using an ACL” on a standalone FortiSwitch appliance, the relevant evidence is to inspect ACL match counters and resulting QoS queue handling.

Question 596

After the team configures “Apply a QoS action using an ACL” on a newly commissioned floor switch, which TWO claims about the configuration are valid? (Choose TWO.)

  1. Time-based ACL scheduling controls policy applicability, not the device system clock itself
  2. The promiscuous port connects secondary VLANs to the common routed or shared service endpoint
  3. An ingress ACL classifies traffic arriving at an interface and applies permitted hardware actions
  4. Inspect ACL match counters and resulting QoS queue handling
  5. ACL actions can assign supported classification or priority treatment to matching frames

Explanation

Correct Answers

D:

The stated check directly tests whether the intended function is active at the distribution floor. It provides evidence about “Apply a QoS action using an ACL” beyond ordinary link-up state on a newly commissioned floor switch.

E:

This is the precise control because the described mechanism corresponds to the operation that administrators use to prioritize a defined class without requiring every endpoint to mark itself. The result should be observable on a newly commissioned floor switch.

Incorrect Answers

A:

That characteristic reflects “Configure an ACL schedule” rather than “Apply a QoS action using an ACL” at the distribution floor. Its actual role is to enforce a selected match/action only during approved operational hours, a different configuration need.

B:

That characteristic reflects “Configure a promiscuous PVLAN port for a shared gateway” rather than “Apply a QoS action using an ACL” at the distribution floor. Its actual role is to provide primary-VLAN reachability to otherwise separated PVLAN hosts, a different configuration need.

C:

That characteristic reflects “Install an ingress ACL for received traffic” rather than “Apply a QoS action using an ACL” at the distribution floor. Its actual role is to filter packets as they enter a FortiSwitch forwarding pipeline, a different configuration need.

Question 597

A deployment review at the media studio identifies this objective: rate-control selected traffic rather than dropping every matching packet. Which FortiSwitch operation should be selected?

  1. Apply an ACL policer to matching frames
  2. Review the ACL hardware resource usage
  3. Apply a community secondary PVLAN to one workgroup
  4. Match an ACL using an IP subnet

Explanation

Correct Answer

A:

The implementation works because a linked policer enforces meter behavior for the matched ACL class. This distinction is material to the media studio, where the stated goal is to rate-control selected traffic rather than dropping every matching packet.

Incorrect Answers

B:

Compared with the requested “Apply an ACL policer to matching frames” at the media studio, this would diagnose rejection of additional switch ACL entries despite apparently valid syntax instead: switch ACL classifiers, groups and counters consume finite hardware resources that can be fragmented. At the media studio, the operational proof would instead be to inspect policer conformance/excess statistics alongside ACL counters, whereas “Review the ACL hardware resource usage” is validated by a different test: inspect ACL usage and available hardware entries before changing rule order.

C:

Compared with the requested “Apply an ACL policer to matching frames” at the media studio, this would allow peers within one designated group to communicate but isolate them from other groups instead: community PVLAN members can communicate with their own community and the promiscuous primary port. At the media studio, the operational proof would instead be to inspect policer conformance/excess statistics alongside ACL counters, whereas “Apply a community secondary PVLAN to one workgroup” is validated by a different test: test peer reachability inside the community and deny a connection to a different community.

D:

For the media studio, “Match an ACL using an IP subnet” is a different type of control from “Apply an ACL policer to matching frames”: an IP source or destination prefix classifier restricts the match to packets meeting the configured address condition. Unlike the requested feature, that setting addresses the need to filter traffic from a designated routed network range, not the objective to rate-control selected traffic rather than dropping every matching packet.

Question 598

The operator has decided to apply an ACL policer to matching frames on a switch used by multiple office teams at the data hall. Which operational behavior is the most reasonable expectation of that specific feature?

  1. Isolated PVLAN ports can reach the promiscuous primary attachment but not one another
  2. ACL actions can assign supported classification or priority treatment to matching frames
  3. An egress-stage policy acts on frames being transmitted rather than their original entry classification
  4. A linked policer enforces meter behavior for the matched ACL class

Explanation

Correct Answer

D:

Given the described goal, the configured operation is meant to rate-control selected traffic rather than dropping every matching packet. The most relevant validation is to inspect policer conformance/excess statistics alongside ACL counters for the equipment at the data hall.

Incorrect Answers

A:

That behavior applies when engineers “Apply an isolated secondary PVLAN for tenant servers”; the different operation “Apply an ACL policer to matching frames” is intended to rate-control selected traffic rather than dropping every matching packet. That different feature is verified by test server-to-gateway reachability and server-to-server isolation within the isolated VLAN; for “Apply an ACL policer to matching frames” on a switch used by multiple office teams, the relevant evidence is to inspect policer conformance/excess statistics alongside ACL counters.

B:

This outcome would be relevant to “Apply a QoS action using an ACL” at the data hall, not the task “Apply an ACL policer to matching frames”; the other task is to prioritize a defined class without requiring every endpoint to mark itself. The action “Apply an ACL policer to matching frames” targets a different result: a linked policer enforces meter behavior for the matched ACL class; the proposed alternative would instead be checked by inspect ACL match counters and resulting QoS queue handling.

C:

That behavior applies when engineers “Install an egress ACL for outgoing traffic”; the different operation “Apply an ACL policer to matching frames” is intended to rate-control selected traffic rather than dropping every matching packet. That different feature is verified by inspect egress ACL counters for the relevant outgoing port; for “Apply an ACL policer to matching frames” on a switch used by multiple office teams, the relevant evidence is to inspect policer conformance/excess statistics alongside ACL counters.

Question 599

On a managed switch running FortiSwitchOS 7.6 at the development floor, the team reports that it has configured “Apply an ACL policer to matching frames.” Which verification provides the strongest direct evidence that the intended function is working?

  1. Inspect gateway reachability from each secondary VLAN without direct host-to-host communication
  2. Review ingress ACL match counters while sending matching test frames
  3. Read the EtherType from the frame header and inspect the ACL service match
  4. Inspect policer conformance/excess statistics alongside ACL counters
  5. Compare current FortiSwitch time with the configured schedule and observed rule counters

Explanation

Correct Answer

D:

The switch behavior that matters is: a linked policer enforces meter behavior for the matched ACL class. Directly measuring that result demonstrates whether the step to rate-control selected traffic rather than dropping every matching packet succeeded on a managed switch running FortiSwitchOS 7.6.

Incorrect Answers

A:

The proposed check concerns “Configure a promiscuous PVLAN port for a shared gateway” rather than “Apply an ACL policer to matching frames”: the promiscuous port connects secondary VLANs to the common routed or shared service endpoint. For “Apply an ACL policer to matching frames” on a managed switch running FortiSwitchOS 7.6, a better test would be to inspect policer conformance/excess statistics alongside ACL counters, which targets rate-control selected traffic rather than dropping every matching packet rather than the alternative diagnostic “Configure a promiscuous PVLAN port for a shared gateway”.

B:

This check is suited to “Install an ingress ACL for received traffic” when trying to filter packets as they enter a FortiSwitch forwarding pipeline, not to verify “Apply an ACL policer to matching frames” at the development floor. Checking “Apply an ACL policer to matching frames” at the development floor requires evidence of its own mechanism: a linked policer enforces meter behavior for the matched ACL class; that is not the outcome measured by “Install an ingress ACL for received traffic”.

C:

The proposed check concerns “Use an ACL Ethernet-type classifier” rather than “Apply an ACL policer to matching frames”: an EtherType comparison identifies the payload protocol without relying on TCP/UDP port numbers. For “Apply an ACL policer to matching frames” on a managed switch running FortiSwitchOS 7.6, a better test would be to inspect policer conformance/excess statistics alongside ACL counters, which targets rate-control selected traffic rather than dropping every matching packet rather than the alternative diagnostic “Use an ACL Ethernet-type classifier”.

E:

This check is suited to “Configure an ACL schedule” when trying to enforce a selected match/action only during approved operational hours, not to verify “Apply an ACL policer to matching frames” at the development floor. Checking “Apply an ACL policer to matching frames” at the development floor requires evidence of its own mechanism: a linked policer enforces meter behavior for the matched ACL class; that is not the outcome measured by “Configure an ACL schedule”.

Question 600

On a remote FortiSwitch installation in the conference venue, the next task is to block a targeted source or protocol using explicit hardware filtering. What is the appropriate configuration decision?

  1. Apply a community secondary PVLAN to one workgroup
  2. Drop matched unwanted frames with an ACL action
  3. Match an ACL using an IP subnet
  4. Review the ACL hardware resource usage

Explanation

Correct Answer

B:

At this network boundary, a drop action discards frames meeting the ACL match rather than disabling the whole physical port. The operator can test this claim by the specific check: confirm matching test packets are counted and discarded while unrelated traffic still passes.

Incorrect Answers

A:

Compared with the requested “Drop matched unwanted frames with an ACL action” at the conference venue, this would allow peers within one designated group to communicate but isolate them from other groups instead: community PVLAN members can communicate with their own community and the promiscuous primary port. At the conference venue, the operational proof would instead be to confirm matching test packets are counted and discarded while unrelated traffic still passes, whereas “Apply a community secondary PVLAN to one workgroup” is validated by a different test: test peer reachability inside the community and deny a connection to a different community.

C:

For the conference venue, “Match an ACL using an IP subnet” is a different type of control from “Drop matched unwanted frames with an ACL action”: an IP source or destination prefix classifier restricts the match to packets meeting the configured address condition. Unlike the requested feature, that setting addresses the need to filter traffic from a designated routed network range, not the objective to block a targeted source or protocol using explicit hardware filtering.

D:

Compared with the requested “Drop matched unwanted frames with an ACL action” at the conference venue, this would diagnose rejection of additional switch ACL entries despite apparently valid syntax instead: switch ACL classifiers, groups and counters consume finite hardware resources that can be fragmented. At the conference venue, the operational proof would instead be to confirm matching test packets are counted and discarded while unrelated traffic still passes, whereas “Review the ACL hardware resource usage” is validated by a different test: inspect ACL usage and available hardware entries before changing rule order.

Fortinet NSE 5 - FortiSwitch 7.6 Administrator (NSE5_FSW_AD-7.6) Practice Tests