Fortinet NSE6_OTS_AR-7.6 (Fortinet NSE 6 - OT Security 7.6 Architect) Practice Test 20

Question 190

A technician reviewing security evidence from the district heating plant finds that an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet. What is the most targeted response?

  1. Document MAC/VLAN boundaries separately from routed policy conduits
  2. Restrict only the plant's outbound Internet URL categories
  3. Validate the industrial redundancy mechanism and the firewall failure behavior together
  4. Put a suitable intra-zone enforcement point on the actual device-to-device path

Explanation

Correct Answer

D:

For the stated gap at the district heating plant, microsegmentation requires the target communications to cross a control capable of applying per-flow rules; that directly resolves the requirement that an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet.

Incorrect Answers

A:

At the district heating plant, this mechanism serves the separate situation where controls engineers need to identify which flows must remain routable while preserving the existing layer-two broadcast structure, whereas the present finding is that an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet; although switching domains and layer-three enforcement are different constructs that must both be represented in the design, the required capability remains missing.

B:

At the district heating plant, that alternative is insufficient because external browsing filters do not govern local device-to-device traffic inside the control zone; it leaves unresolved the finding that an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet.

C:

At the district heating plant, this mechanism serves the separate situation where a ring-topology automation network has stringent recovery-time requirements before a segmentation change, whereas the present finding is that an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet; although acceptable availability depends on convergence and failover characteristics of the whole industrial path, the required capability remains missing.

Question 191

A plant security engineer at the mineral processing site needs a focused remedy because repeated unauthorized maintenance attempts should become one notable security incident under a defined time threshold. What is the most targeted response?

  1. Select the relevant device or user key attributes when defining incident grouping
  2. Configure a static asset inventory export as the detection rule
  3. Map meaningful triggered attributes into the incident details and review parsed device fields
  4. Build a FortiSIEM correlation rule with appropriate conditions and time window

Explanation

Correct Answer

D:

In this mineral processing site scenario, rule aggregation across related events can identify repeated suspicious behavior rather than separate isolated messages; that directly resolves the requirement that repeated unauthorized maintenance attempts should become one notable security incident under a defined time threshold.

Incorrect Answers

A:

At the mineral processing site, this mechanism serves the separate situation where correlation incident reports incorrectly join independent hosts because the selected incident grouping key is too broad, whereas the present finding is that repeated unauthorized maintenance attempts should become one notable security incident under a defined time threshold; although incident identity keys determine whether new matching events increment an existing incident or raise a separate one, the required capability remains missing.

B:

At the mineral processing site, this substitutes a measure addressing a different concern: an inventory snapshot does not evaluate event frequency over time; it leaves unresolved the finding that repeated unauthorized maintenance attempts should become one notable security incident under a defined time threshold.

C:

At the mineral processing site, this mechanism serves the separate situation where a rule tests event sequences but the analyst cannot identify the actual controller that triggered an incident, whereas the present finding is that repeated unauthorized maintenance attempts should become one notable security incident under a defined time threshold; although the triggered context should retain the affected industrial entity to support triage and follow-up, the required capability remains missing.

Question 192

During a maintenance-window design exercise for the hydroelectric generation site, the team notes: (1) an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions; and (2) a suspected compromised maintenance laptop must be contained while continuing operation of fixed safety controllers. Which proposal would pass both acceptance tests with the fewest irrelevant changes?

  1. Identify DNP3 traffic using its industrial protocol context and configured communications pattern; then disconnect the complete PLC subnet in response to one laptop alert
  2. Apply a generic HTTP-only parsing assumption to DNP3 events; then target the affected noncritical endpoint through FortiNAC or policy-based access restriction
  3. Identify DNP3 traffic using its industrial protocol context and configured communications pattern; then target the affected noncritical endpoint through FortiNAC or policy-based access restriction
  4. Apply a generic HTTP-only parsing assumption to DNP3 events; then disconnect the complete PLC subnet in response to one laptop alert

Explanation

Correct Answer

C:

The first control fits because DNP3 supports telemetry and control exchanges that require different baselines from web browsing; the second fits because containment should act on the identified workstation rather than remove an entire safety-critical control cell. Together they resolve the separate findings at the hydroelectric generation site: an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions, and a suspected compromised maintenance laptop must be contained while continuing operation of fixed safety controllers. This addresses an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions without bypassing the separate requirement that a suspected compromised maintenance laptop must be contained while continuing operation of fixed safety controllers.

Incorrect Answers

A:

The first action is suitable because DNP3 supports telemetry and control exchanges that require different baselines from web browsing; the second is misdirected because subnet-wide isolation sacrifices unrelated process availability and exceeds the identified blast radius. At the hydroelectric generation site, the remaining second gap is that a suspected compromised maintenance laptop must be contained while continuing operation of fixed safety controllers, even though an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions is covered.

B:

The second part is useful because containment should act on the identified workstation rather than remove an entire safety-critical control cell; however, the first part fails because a web request parser does not describe DNP3 operational functions or expected field-device messages. The first gap remains unresolved at the hydroelectric generation site: an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions; the second measure helps with a suspected compromised maintenance laptop must be contained while continuing operation of fixed safety controllers but cannot repair it.

D:

The first substitution fails because a web request parser does not describe DNP3 operational functions or expected field-device messages; the second fails because subnet-wide isolation sacrifices unrelated process availability and exceeds the identified blast radius. For this hydroelectric generation site, the first finding is that an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions, while the other is that a suspected compromised maintenance laptop must be contained while continuing operation of fixed safety controllers; neither is corrected by the chosen substitutions.

Question 193

Before exposing an OT interconnection at the food-processing factory, the design must resolve both findings: (1) the OT VLAN design is complete but traffic can still traverse a permissive routed interface between the VLANs; and (2) a disabled endpoint must have substantially no operational-network access regardless of prior registration. Which two measures correctly map to the operational and security requirements?

  1. Create more descriptive VLAN names and keep the router unrestricted; then re-enable the device automatically whenever it reconnects
  2. Add explicit inter-VLAN firewall policy at the routing boundary; then re-enable the device automatically whenever it reconnects
  3. Keep cell-specific forwarding contexts logically isolated and define explicit interconnections; then use the FortiNAC disabled or dead-end isolation enforcement state
  4. Add explicit inter-VLAN firewall policy at the routing boundary; then use the FortiNAC disabled or dead-end isolation enforcement state
  5. Create more descriptive VLAN names and keep the router unrestricted; then use the FortiNAC disabled or dead-end isolation enforcement state

Explanation

Correct Answer

D:

The first control fits because separate layer-two membership does not automatically prevent routed communication through an allowed path; the second fits because a disabled host should be held in a restrictive network state instead of rejoining production. Together they resolve the separate findings at the food-processing factory: the OT VLAN design is complete but traffic can still traverse a permissive routed interface between the VLANs, and a disabled endpoint must have substantially no operational-network access regardless of prior registration. This addresses the OT VLAN design is complete but traffic can still traverse a permissive routed interface between the VLANs without bypassing the separate requirement that a disabled endpoint must have substantially no operational-network access regardless of prior registration.

Incorrect Answers

A:

The first substitution fails because naming network segments changes no layer-three authorization decisions; the second fails because reconnecting does not override the administrator's disabled state. For this food-processing factory, the first finding is that the OT VLAN design is complete but traffic can still traverse a permissive routed interface between the VLANs, while the other is that a disabled endpoint must have substantially no operational-network access regardless of prior registration; neither is corrected by the chosen substitutions.

B:

The first action is suitable because separate layer-two membership does not automatically prevent routed communication through an allowed path; the second is misdirected because reconnecting does not override the administrator's disabled state. At the food-processing factory, the remaining second gap is that a disabled endpoint must have substantially no operational-network access regardless of prior registration, even though the OT VLAN design is complete but traffic can still traverse a permissive routed interface between the VLANs is covered.

C:

The second action addresses a disabled endpoint must have substantially no operational-network access regardless of prior registration because a disabled host should be held in a restrictive network state instead of rejoining production, but the separate first finding still concerns the OT VLAN design is complete but traffic can still traverse a permissive routed interface between the VLANs. The proposed first mechanism belongs to a different requirement: multiple industrial cells use identical private addressing and must share one physical firewall without merging their networks; separate routing contexts prevent accidental overlap while making required shared services deliberate, but despite the valid second control for a disabled endpoint must have substantially no operational-network access regardless of prior registration, it does not resolve the first finding at the food-processing factory: the OT VLAN design is complete but traffic can still traverse a permissive routed interface between the VLANs.

E:

The second part is useful because a disabled host should be held in a restrictive network state instead of rejoining production; however, the first part fails because naming network segments changes no layer-three authorization decisions. The first gap remains unresolved at the food-processing factory: the OT VLAN design is complete but traffic can still traverse a permissive routed interface between the VLANs; the second measure helps with a disabled endpoint must have substantially no operational-network access regardless of prior registration but cannot repair it.

Question 194

Before the regional pipeline control center accepts a proposed OT security architecture, it must demonstrate: (1) the team expects current device vulnerability mappings after new FortiGuard definitions are issued; and (2) an OPC UA telemetry server must serve selected clients but no other production hosts. What is the technically justified combination for the two separate observations?

  1. Check valid update connectivity or the approved offline package update path; then restrict OPC UA communications to approved clients and endpoints with appropriate protocol awareness
  2. Depend on firmware uptime to make signatures self-update; then permit arbitrary inbound sessions to all OPC UA endpoints
  3. Prioritize a temporary validated network mitigation and track the residual remediation task; then restrict OPC UA communications to approved clients and endpoints with appropriate protocol awareness
  4. Check valid update connectivity or the approved offline package update path; then permit arbitrary inbound sessions to all OPC UA endpoints
  5. Depend on firmware uptime to make signatures self-update; then restrict OPC UA communications to approved clients and endpoints with appropriate protocol awareness

Explanation

Correct Answer

A:

The first control fits because local signature and vulnerability intelligence must be refreshed through an authorized update workflow; the second fits because restricting clients and service endpoints preserves authorized data exchange without treating the server as public infrastructure. Together they resolve the separate findings at the regional pipeline control center: the team expects current device vulnerability mappings after new FortiGuard definitions are issued, and an OPC UA telemetry server must serve selected clients but no other production hosts. This addresses the team expects current device vulnerability mappings after new FortiGuard definitions are issued without bypassing the separate requirement that an OPC UA telemetry server must serve selected clients but no other production hosts.

Incorrect Answers

B:

The first substitution fails because elapsed running time is not a mechanism for acquiring new threat definitions; the second fails because open access disregards the intended client and server trust boundary. For this regional pipeline control center, the first finding is that the team expects current device vulnerability mappings after new FortiGuard definitions are issued, while the other is that an OPC UA telemetry server must serve selected clients but no other production hosts; neither is corrected by the chosen substitutions.

C:

The second action addresses an OPC UA telemetry server must serve selected clients but no other production hosts because restricting clients and service endpoints preserves authorized data exchange without treating the server as public infrastructure, but the separate first finding still concerns the team expects current device vulnerability mappings after new FortiGuard definitions are issued. The proposed first mechanism belongs to a different requirement: OT asset intelligence shows a known exploited vulnerability in a controller but the maintenance patch is deferred; KEV context raises exploit concern while temporary protection should remain linked to the eventual vendor fix, but despite the valid second control for an OPC UA telemetry server must serve selected clients but no other production hosts, it does not resolve the first finding at the regional pipeline control center: the team expects current device vulnerability mappings after new FortiGuard definitions are issued.

D:

The first action is suitable because local signature and vulnerability intelligence must be refreshed through an authorized update workflow; the second is misdirected because open access disregards the intended client and server trust boundary. At the regional pipeline control center, the remaining second gap is that an OPC UA telemetry server must serve selected clients but no other production hosts, even though the team expects current device vulnerability mappings after new FortiGuard definitions are issued is covered.

E:

The second part is useful because restricting clients and service endpoints preserves authorized data exchange without treating the server as public infrastructure; however, the first part fails because elapsed running time is not a mechanism for acquiring new threat definitions. The first gap remains unresolved at the regional pipeline control center: the team expects current device vulnerability mappings after new FortiGuard definitions are issued; the second measure helps with an OPC UA telemetry server must serve selected clients but no other production hosts but cannot repair it.

Question 195

For the upcoming controlled rollout at the rail signaling depot, the work package includes: (1) the plant wants OT signatures to inspect a controller conduit but the policy has no active IPS profile; and (2) a virtual patching rule cannot identify which detected industrial endpoint the vulnerability applies to. Which paired configuration should be included in the approved OT security change?

  1. Enable a suitable IPS security profile on the conduit firewall policy; then turn off all device identification and expect target-specific rules
  2. Enable only traffic logging while leaving IPS disabled; then enable and verify relevant device identification before expecting per-device virtual patch lookup
  3. Enable a suitable IPS security profile on the conduit firewall policy; then enable and verify relevant device identification before expecting per-device virtual patch lookup
  4. Enable only traffic logging while leaving IPS disabled; then turn off all device identification and expect target-specific rules

Explanation

Correct Answer

C:

The first control fits because the dedicated OT attack definitions are used by IPS inspection when the service is valid and policy is configured; the second fits because observed device attributes supply the context used to match vulnerabilities and protection rules. Together they resolve the separate findings at the rail signaling depot: the plant wants OT signatures to inspect a controller conduit but the policy has no active IPS profile, and a virtual patching rule cannot identify which detected industrial endpoint the vulnerability applies to. This addresses the plant wants OT signatures to inspect a controller conduit but the policy has no active IPS profile without bypassing the separate requirement that a virtual patching rule cannot identify which detected industrial endpoint the vulnerability applies to.

Incorrect Answers

A:

The first action is suitable because the dedicated OT attack definitions are used by IPS inspection when the service is valid and policy is configured; the second is misdirected because disabling discovery removes input that the device-aware matching process requires. At the rail signaling depot, the remaining second gap is that a virtual patching rule cannot identify which detected industrial endpoint the vulnerability applies to, even though the plant wants OT signatures to inspect a controller conduit but the policy has no active IPS profile is covered.

B:

The second part is useful because observed device attributes supply the context used to match vulnerabilities and protection rules; however, the first part fails because recording session metadata does not cause threat signatures to be evaluated. The first gap remains unresolved at the rail signaling depot: the plant wants OT signatures to inspect a controller conduit but the policy has no active IPS profile; the second measure helps with a virtual patching rule cannot identify which detected industrial endpoint the vulnerability applies to but cannot repair it.

D:

The first substitution fails because recording session metadata does not cause threat signatures to be evaluated; the second fails because disabling discovery removes input that the device-aware matching process requires. For this rail signaling depot, the first finding is that the plant wants OT signatures to inspect a controller conduit but the policy has no active IPS profile, while the other is that a virtual patching rule cannot identify which detected industrial endpoint the vulnerability applies to; neither is corrected by the chosen substitutions.

Question 196

A targeted security validation of the building-management control network specifies the following: (1) a correlation rule merges activity from different PLCs into one undifferentiated incident; and (2) correlation incident reports incorrectly join independent hosts because the selected incident grouping key is too broad. What is the technically justified combination for the two separate observations?

  1. Refine the relevant event grouping using asset identity and correlation attributes; then select the relevant device or user key attributes when defining incident grouping
  2. Group incidents only by the calendar month; then select the relevant device or user key attributes when defining incident grouping
  3. Refine the relevant event grouping using asset identity and correlation attributes; then use the display severity as the only incident grouping attribute
  4. Group incidents only by the calendar month; then use the display severity as the only incident grouping attribute

Explanation

Correct Answer

A:

The first control fits because matching on the affected device helps preserve which industrial endpoint generated each event sequence; the second fits because incident identity keys determine whether new matching events increment an existing incident or raise a separate one. Together they resolve the separate findings at the building-management control network: a correlation rule merges activity from different PLCs into one undifferentiated incident, and correlation incident reports incorrectly join independent hosts because the selected incident grouping key is too broad. This addresses a correlation rule merges activity from different PLCs into one undifferentiated incident without bypassing the separate requirement that correlation incident reports incorrectly join independent hosts because the selected incident grouping key is too broad.

Incorrect Answers

B:

The second part is useful because incident identity keys determine whether new matching events increment an existing incident or raise a separate one; however, the first part fails because coarse time grouping cannot distinguish activity targeting different controllers. The first gap remains unresolved at the building-management control network: a correlation rule merges activity from different PLCs into one undifferentiated incident; the second measure helps with correlation incident reports incorrectly join independent hosts because the selected incident grouping key is too broad but cannot repair it.

C:

The first action is suitable because matching on the affected device helps preserve which industrial endpoint generated each event sequence; the second is misdirected because a shared severity label does not distinguish independent source-device incident sequences. At the building-management control network, the remaining second gap is that correlation incident reports incorrectly join independent hosts because the selected incident grouping key is too broad, even though a correlation rule merges activity from different PLCs into one undifferentiated incident is covered.

D:

The first substitution fails because coarse time grouping cannot distinguish activity targeting different controllers; the second fails because a shared severity label does not distinguish independent source-device incident sequences. For this building-management control network, the first finding is that a correlation rule merges activity from different PLCs into one undifferentiated incident, while the other is that correlation incident reports incorrectly join independent hosts because the selected incident grouping key is too broad; neither is corrected by the chosen substitutions.

Question 197

An OT architect reviewing the pharmaceutical production floor observes two independent gaps: (1) a North American electric utility needs to relate its cyber-system inventory and perimeter protections to the applicable NERC CIP obligations; and (2) the OT team cannot tell which industrial asset provided the source IP of a detected threat. Which combination addresses the required mechanisms at their proper enforcement or observation points?

  1. Use only a general IT security score without identifying BES Cyber Systems; then remove source identity fields from the SIEM ingest pipeline
  2. Identify applicable BES Cyber Systems and evaluate relevant NERC CIP requirements; then remove source identity fields from the SIEM ingest pipeline
  3. Define zone-specific security requirements and assess the conduits connecting them; then associate firewall events with resolved device identity and asset attributes
  4. Use only a general IT security score without identifying BES Cyber Systems; then associate firewall events with resolved device identity and asset attributes
  5. Identify applicable BES Cyber Systems and evaluate relevant NERC CIP requirements; then associate firewall events with resolved device identity and asset attributes

Explanation

Correct Answer

E:

The first control fits because applicability and asset classification determine which NERC CIP safeguards must be assessed for the electric utility; the second fits because enriched asset-to-IP associations make events actionable for specific controllers instead of only transient addresses. Together they resolve the separate findings at the pharmaceutical production floor: a North American electric utility needs to relate its cyber-system inventory and perimeter protections to the applicable NERC CIP obligations, and the OT team cannot tell which industrial asset provided the source IP of a detected threat. This addresses a North American electric utility needs to relate its cyber-system inventory and perimeter protections to the applicable NERC CIP obligations without bypassing the separate requirement that the OT team cannot tell which industrial asset provided the source IP of a detected threat.

Incorrect Answers

A:

The first substitution fails because a general security score cannot determine which electric-sector systems and obligations apply; the second fails because discarding device identity prevents analysts from relating alerts to the affected industrial asset. For this pharmaceutical production floor, the first finding is that a North American electric utility needs to relate its cyber-system inventory and perimeter protections to the applicable NERC CIP obligations, while the other is that the OT team cannot tell which industrial asset provided the source IP of a detected threat; neither is corrected by the chosen substitutions.

B:

The first action is suitable because applicability and asset classification determine which NERC CIP safeguards must be assessed for the electric utility; the second is misdirected because discarding device identity prevents analysts from relating alerts to the affected industrial asset. At the pharmaceutical production floor, the remaining second gap is that the OT team cannot tell which industrial asset provided the source IP of a detected threat, even though a North American electric utility needs to relate its cyber-system inventory and perimeter protections to the applicable NERC CIP obligations is covered.

C:

The second action addresses the OT team cannot tell which industrial asset provided the source IP of a detected threat because enriched asset-to-IP associations make events actionable for specific controllers instead of only transient addresses, but the separate first finding still concerns a North American electric utility needs to relate its cyber-system inventory and perimeter protections to the applicable NERC CIP obligations. The proposed first mechanism belongs to a different requirement: the compliance workshop asks for a documented risk-based control approach to OT system security under ISA/IEC 62443; ISA/IEC 62443 promotes risk-informed partitioning and explicitly governed communications across trust boundaries, but despite the valid second control for the OT team cannot tell which industrial asset provided the source IP of a detected threat, it does not resolve the first finding at the pharmaceutical production floor: a North American electric utility needs to relate its cyber-system inventory and perimeter protections to the applicable NERC CIP obligations.

D:

The second part is useful because enriched asset-to-IP associations make events actionable for specific controllers instead of only transient addresses; however, the first part fails because a general security score cannot determine which electric-sector systems and obligations apply. The first gap remains unresolved at the pharmaceutical production floor: a North American electric utility needs to relate its cyber-system inventory and perimeter protections to the applicable NERC CIP obligations; the second measure helps with the OT team cannot tell which industrial asset provided the source IP of a detected threat but cannot repair it.

Question 198

An audit at the cement kiln control room finds that a basic handler exists but the incident queue remains empty after the intended event fires. What is the most targeted response?

  1. Enable automatic incident creation in the relevant FortiAnalyzer event handler
  2. Narrow the selected log sources and filtering fields to the relevant OT events
  3. Build a FortiAnalyzer event handler filtered for the relevant OT threat log fields
  4. Increase the handler severity while leaving automatic incident creation disabled

Explanation

Correct Answer

A:

The relevant technical distinction for the cement kiln control room is that FortiAnalyzer can turn qualifying handler events into incidents when the create-incident setting is enabled; that directly resolves the requirement that a basic handler exists but the incident queue remains empty after the intended event fires.

Incorrect Answers

B:

At the cement kiln control room, this mechanism serves the separate situation where a handler fires on unrelated business traffic because its log selection includes the wrong source and subtype, whereas the present finding is that a basic handler exists but the incident queue remains empty after the intended event fires; although the event handler's data selection and filters determine the events that qualify, the required capability remains missing.

C:

At the cement kiln control room, this mechanism serves the separate situation where operations want an alert when a specific industrial IPS signature appears in FortiGate traffic logs, whereas the present finding is that a basic handler exists but the incident queue remains empty after the intended event fires; although event handlers evaluate selected logs and generate actionable events when their conditions match, the required capability remains missing.

D:

The mismatch at the cement kiln control room is specific to the observed control requirement: raising the event severity does not activate the distinct incident-creation switch; it leaves unresolved the finding that a basic handler exists but the incident queue remains empty after the intended event fires.

Question 199

During troubleshooting of the district heating plant, the operator confirms that a basic handler exists but the incident queue remains empty after the intended event fires. The proposed shortcut is to increase the handler severity while leaving automatic incident creation disabled. Which alternative should the architect approve instead?

  1. Enable automatic incident creation in the relevant FortiAnalyzer event handler
  2. Narrow the selected log sources and filtering fields to the relevant OT events
  3. Increase the handler severity while leaving automatic incident creation disabled
  4. Build a FortiAnalyzer event handler filtered for the relevant OT threat log fields

Explanation

Correct Answer

A:

At the district heating plant, FortiAnalyzer can turn qualifying handler events into incidents when the create-incident setting is enabled; that directly resolves the requirement that a basic handler exists but the incident queue remains empty after the intended event fires.

Incorrect Answers

B:

At the district heating plant, this mechanism serves the separate situation where a handler fires on unrelated business traffic because its log selection includes the wrong source and subtype, whereas the present finding is that a basic handler exists but the incident queue remains empty after the intended event fires; although the event handler's data selection and filters determine the events that qualify, the required capability remains missing.

C:

At the district heating plant, the expected mechanism is absent because raising the event severity does not activate the distinct incident-creation switch; it leaves unresolved the finding that a basic handler exists but the incident queue remains empty after the intended event fires.

D:

At the district heating plant, this mechanism serves the separate situation where operations want an alert when a specific industrial IPS signature appears in FortiGate traffic logs, whereas the present finding is that a basic handler exists but the incident queue remains empty after the intended event fires; although event handlers evaluate selected logs and generate actionable events when their conditions match, the required capability remains missing.

Question 200

An OT architect reviewing the electric distribution substation observes two independent gaps: (1) a security team wants evidence related to its baseline CIS Controls implementation; and (2) operations wants a site-specific FortiSIEM dashboard rather than a corporate-wide incident summary. Which two measures correctly map to the operational and security requirements?

  1. Interpret an antivirus signature count as a CIS compliance certificate; then filter the dashboard on the OT site, incident dimensions and period of interest
  2. Use the appropriate CIS Controls Security Rating report and review its underlying checks; then filter the dashboard on the OT site, incident dimensions and period of interest
  3. Interpret an antivirus signature count as a CIS compliance certificate; then reuse an unfiltered global dashboard as proof of site-only risk
  4. Use the appropriate CIS Controls Security Rating report and review its underlying checks; then reuse an unfiltered global dashboard as proof of site-only risk

Explanation

Correct Answer

B:

The first control fits because CIS-aligned ratings summarize the evaluated security controls rather than proving unrestricted compliance; the second fits because site and time scoping align the visualization with local risk owners. Together they resolve the separate findings at the electric distribution substation: a security team wants evidence related to its baseline CIS Controls implementation, and operations wants a site-specific FortiSIEM dashboard rather than a corporate-wide incident summary. This addresses a security team wants evidence related to its baseline CIS Controls implementation without bypassing the separate requirement that operations wants a site-specific FortiSIEM dashboard rather than a corporate-wide incident summary.

Incorrect Answers

A:

The second part is useful because site and time scoping align the visualization with local risk owners; however, the first part fails because update counts do not assess all of the control areas needed for a security rating. The first gap remains unresolved at the electric distribution substation: a security team wants evidence related to its baseline CIS Controls implementation; the second measure helps with operations wants a site-specific FortiSIEM dashboard rather than a corporate-wide incident summary but cannot repair it.

C:

The first substitution fails because update counts do not assess all of the control areas needed for a security rating; the second fails because enterprise aggregates cannot isolate the plant's contribution without appropriate scoping. For this electric distribution substation, the first finding is that a security team wants evidence related to its baseline CIS Controls implementation, while the other is that operations wants a site-specific FortiSIEM dashboard rather than a corporate-wide incident summary; neither is corrected by the chosen substitutions.

D:

The first action is suitable because CIS-aligned ratings summarize the evaluated security controls rather than proving unrestricted compliance; the second is misdirected because enterprise aggregates cannot isolate the plant's contribution without appropriate scoping. At the electric distribution substation, the remaining second gap is that operations wants a site-specific FortiSIEM dashboard rather than a corporate-wide incident summary, even though a security team wants evidence related to its baseline CIS Controls implementation is covered.

Fortinet NSE 6 - OT Security 7.6 Architect (NSE6_OTS_AR-7.6) Practice Tests