Question 380
An audit at the paper mill control network finds that incident responders need to investigate why a FortiAnalyzer aggregate chart spikes on one production unit. The proposed shortcut is to decide the root cause using only the total number printed on the chart. Which alternative should the architect approve instead?
- Drill into the supporting events, devices and time range behind the report
- Schedule and scope a FortiAnalyzer report using appropriate OT datasets
- Decide the root cause using only the total number printed on the chart
- Check the report's selected data source, time range and incident filters
Explanation
Correct Answer
A:In this paper mill control network scenario, source event details are needed to separate a real security change from collection noise; that directly resolves the requirement that incident responders need to investigate why a FortiAnalyzer aggregate chart spikes on one production unit.
Incorrect Answers
B:At the paper mill control network, this mechanism serves the separate situation where managers need repeated OT threat trends from FortiAnalyzer without manually collecting individual firewall logs, whereas the present finding is that incident responders need to investigate why a FortiAnalyzer aggregate chart spikes on one production unit; although reports aggregate retained security data into a repeatable operational review artifact, the required capability remains missing.
C:At the paper mill control network, this substitutes a measure addressing a different concern: an aggregate count cannot identify the affected controller or triggering detection; it leaves unresolved the finding that incident responders need to investigate why a FortiAnalyzer aggregate chart spikes on one production unit.
D:At the paper mill control network, this mechanism serves the separate situation where a FortiSIEM report is empty even though operators know incidents exist for the same week, whereas the present finding is that incident responders need to investigate why a FortiAnalyzer aggregate chart spikes on one production unit; although reporting queries depend on correctly scoped events and normalized incident data, the required capability remains missing.
Question 381
A plant security engineer at the district water pumping plant needs a focused remedy because a plant needs to block an unauthorized engineering workstation moving from a packaging cell into a utilities cell. What is the most targeted response?
- Enforce a cell-to-cell allowlist at a routed or transparent segmentation boundary
- Restrict the approved traffic at the correct conduit using protocol-aware controls where available
- Use a controlled remote-access termination and a monitored jump host into permitted OT destinations
- Assume a perimeter Internet firewall sees every cell-to-cell packet
Explanation
Correct Answer
A:In this district water pumping plant scenario, crossing-cell policy distinguishes approved production exchanges from workstation lateral movement; that directly resolves the requirement that a plant needs to block an unauthorized engineering workstation moving from a packaging cell into a utilities cell.
Incorrect Answers
B:At the district water pumping plant, this mechanism serves the separate situation where the process historian may only initiate read requests to certain controllers and arbitrary writes are prohibited, whereas the present finding is that a plant needs to block an unauthorized engineering workstation moving from a packaging cell into a utilities cell; although limiting communications by destination and industrial operation reduces the blast radius of unauthorized commands, the required capability remains missing.
C:At the district water pumping plant, this mechanism serves the separate situation where a contractor requires short-lived access to OT but must not receive direct reachability from unmanaged external devices, whereas the present finding is that a plant needs to block an unauthorized engineering workstation moving from a packaging cell into a utilities cell; although brokered privileged access reduces direct exposure and supports session accountability, the required capability remains missing.
D:At the district water pumping plant, this substitutes a measure addressing a different concern: internal switches may forward the lateral exchange without crossing the external perimeter; it leaves unresolved the finding that a plant needs to block an unauthorized engineering workstation moving from a packaging cell into a utilities cell.
Question 382
The site owner of the wastewater pumping station requests a targeted response to these observations: (1) a basic handler exists but the incident queue remains empty after the intended event fires; and (2) an OT vulnerability is severe on paper but belongs to an isolated device with compensating controls. Which joint design is aligned with the exact detection and enforcement gaps?
- Increase the handler severity while leaving automatic incident creation disabled; then rank treatment using exposure, likelihood, consequence and validated existing controls
- Enable automatic incident creation in the relevant FortiAnalyzer event handler; then assign priority solely from the CVE title's alphabetical order
- Increase the handler severity while leaving automatic incident creation disabled; then assign priority solely from the CVE title's alphabetical order
- Narrow the selected log sources and filtering fields to the relevant OT events; then rank treatment using exposure, likelihood, consequence and validated existing controls
- Enable automatic incident creation in the relevant FortiAnalyzer event handler; then rank treatment using exposure, likelihood, consequence and validated existing controls
Explanation
Correct Answer
E:The first control fits because FortiAnalyzer can turn qualifying handler events into incidents when the create-incident setting is enabled; the second fits because risk decisions depend on reachability and operational impact as well as a numerical weakness score. Together they resolve the separate findings at the wastewater pumping station: a basic handler exists but the incident queue remains empty after the intended event fires, and an OT vulnerability is severe on paper but belongs to an isolated device with compensating controls. This addresses a basic handler exists but the incident queue remains empty after the intended event fires without bypassing the separate requirement that an OT vulnerability is severe on paper but belongs to an isolated device with compensating controls.
Incorrect Answers
A:The second part is useful because risk decisions depend on reachability and operational impact as well as a numerical weakness score; however, the first part fails because raising the event severity does not activate the distinct incident-creation switch. The first gap remains unresolved at the wastewater pumping station: a basic handler exists but the incident queue remains empty after the intended event fires; the second measure helps with an OT vulnerability is severe on paper but belongs to an isolated device with compensating controls but cannot repair it.
B:The first action is suitable because FortiAnalyzer can turn qualifying handler events into incidents when the create-incident setting is enabled; the second is misdirected because the spelling of a vulnerability identifier has no causal relation to plant risk. At the wastewater pumping station, the remaining second gap is that an OT vulnerability is severe on paper but belongs to an isolated device with compensating controls, even though a basic handler exists but the incident queue remains empty after the intended event fires is covered.
C:The first substitution fails because raising the event severity does not activate the distinct incident-creation switch; the second fails because the spelling of a vulnerability identifier has no causal relation to plant risk. For this wastewater pumping station, the first finding is that a basic handler exists but the incident queue remains empty after the intended event fires, while the other is that an OT vulnerability is severe on paper but belongs to an isolated device with compensating controls; neither is corrected by the chosen substitutions.
D:The second action addresses an OT vulnerability is severe on paper but belongs to an isolated device with compensating controls because risk decisions depend on reachability and operational impact as well as a numerical weakness score, but the separate first finding still concerns a basic handler exists but the incident queue remains empty after the intended event fires. The proposed first mechanism belongs to a different requirement: a handler fires on unrelated business traffic because its log selection includes the wrong source and subtype; the event handler's data selection and filters determine the events that qualify, but despite the valid second control for an OT vulnerability is severe on paper but belongs to an isolated device with compensating controls, it does not resolve the first finding at the wastewater pumping station: a basic handler exists but the incident queue remains empty after the intended event fires.
Question 383
The natural-gas compression station is preparing a controlled rollout. One outstanding requirement is that the OT architect needs to reduce the attack surface of a specific protocol service that is not required by the process. The proposed shortcut is to add a threat label but preserve the permit-all application list. Which alternative should the architect approve instead?
- Change the relevant signature action under a tested IPS profile and policy
- Enable appropriate industrial-protocol IPS inspection on the matching FortiGate policy
- Add a threat label but preserve the permit-all application list
- Remove that unnecessary service from the segment's firewall allowlist
Explanation
Correct Answer
D:The relevant technical distinction for the natural-gas compression station is that eliminating unneeded permitted services shrinks reachable attack paths independently of signature coverage; that directly resolves the requirement that the OT architect needs to reduce the attack surface of a specific protocol service that is not required by the process.
Incorrect Answers
A:At the natural-gas compression station, this mechanism serves the separate situation where an IPS profile logs detections but the plant's approved response requires blocking a specifically validated malicious signature, whereas the present finding is that the OT architect needs to reduce the attack surface of a specific protocol service that is not required by the process; although alert-only inspection provides visibility whereas a validated block action can stop matched traffic in-path, the required capability remains missing.
B:At the natural-gas compression station, this mechanism serves the separate situation where the firewall permits an industrial TCP port but a malicious operation within that protocol remains undetected, whereas the present finding is that the OT architect needs to reduce the attack surface of a specific protocol service that is not required by the process; although an OT-aware IPS signature can evaluate malicious commands or exploit patterns beyond just the transport port, the required capability remains missing.
C:The mismatch at the natural-gas compression station is specific to the observed control requirement: classification alone does not remove an otherwise allowed protocol path; it leaves unresolved the finding that the OT architect needs to reduce the attack surface of a specific protocol service that is not required by the process.
Question 384
A staged deployment for the semiconductor fabrication facility cannot proceed until both conditions are handled: (1) an IPS profile logs detections but the plant's approved response requires blocking a specifically validated malicious signature; and (2) the security engineer must decide which severity levels are actively blocked and which are only logged. Which two measures correctly map to the operational and security requirements?
- Remove that unnecessary service from the segment's firewall allowlist; then define and test the severity and action choices within a virtual patching profile
- Change the relevant signature action under a tested IPS profile and policy; then increase traffic logging while leaving virtual-patching severity actions unchanged
- Change the report title from alert to blocked; then define and test the severity and action choices within a virtual patching profile
- Change the report title from alert to blocked; then increase traffic logging while leaving virtual-patching severity actions unchanged
- Change the relevant signature action under a tested IPS profile and policy; then define and test the severity and action choices within a virtual patching profile
Explanation
Correct Answer
E:The first control fits because alert-only inspection provides visibility whereas a validated block action can stop matched traffic in-path; the second fits because profile-level action and severity selections set which matched mitigations are enforced versus observed. Together they resolve the separate findings at the semiconductor fabrication facility: an IPS profile logs detections but the plant's approved response requires blocking a specifically validated malicious signature, and the security engineer must decide which severity levels are actively blocked and which are only logged. This addresses an IPS profile logs detections but the plant's approved response requires blocking a specifically validated malicious signature without bypassing the separate requirement that the security engineer must decide which severity levels are actively blocked and which are only logged.
Incorrect Answers
A:The second action addresses the security engineer must decide which severity levels are actively blocked and which are only logged because profile-level action and severity selections set which matched mitigations are enforced versus observed, but the separate first finding still concerns an IPS profile logs detections but the plant's approved response requires blocking a specifically validated malicious signature. The proposed first mechanism belongs to a different requirement: the OT architect needs to reduce the attack surface of a specific protocol service that is not required by the process; eliminating unneeded permitted services shrinks reachable attack paths independently of signature coverage, but despite the valid second control for the security engineer must decide which severity levels are actively blocked and which are only logged, it does not resolve the first finding at the semiconductor fabrication facility: an IPS profile logs detections but the plant's approved response requires blocking a specifically validated malicious signature.
B:The first action is suitable because alert-only inspection provides visibility whereas a validated block action can stop matched traffic in-path; the second is misdirected because extra visibility does not configure which virtual-patching severities should block a session. At the semiconductor fabrication facility, the remaining second gap is that the security engineer must decide which severity levels are actively blocked and which are only logged, even though an IPS profile logs detections but the plant's approved response requires blocking a specifically validated malicious signature is covered.
C:The second part is useful because profile-level action and severity selections set which matched mitigations are enforced versus observed; however, the first part fails because a display label cannot turn a logging-only IPS action into enforcement. The first gap remains unresolved at the semiconductor fabrication facility: an IPS profile logs detections but the plant's approved response requires blocking a specifically validated malicious signature; the second measure helps with the security engineer must decide which severity levels are actively blocked and which are only logged but cannot repair it.
D:The first substitution fails because a display label cannot turn a logging-only IPS action into enforcement; the second fails because extra visibility does not configure which virtual-patching severities should block a session. For this semiconductor fabrication facility, the first finding is that an IPS profile logs detections but the plant's approved response requires blocking a specifically validated malicious signature, while the other is that the security engineer must decide which severity levels are actively blocked and which are only logged; neither is corrected by the chosen substitutions.
Question 385
At a large-scale irrigation installation, engineers must address both of these documented gaps: (1) assets with unlike safety and trust requirements are treated as a single flat security group despite an ISA/IEC 62443 zone-and-conduit design requirement; and (2) an already registered device was classified incorrectly and rerunning rogue rules does not change it. Which TWO independently necessary controls directly fulfill the two requirements? Choose TWO.
- Group systems into security zones and document controlled conduits between them
- Run rogue profiling repeatedly without changing registration state
- Document switch-port asset labels without defining inter-zone policies
- Manually correct the registered host or reintroduce it into the appropriate classification workflow
Explanation
Correct Answers
A:For the stated gap at the large-scale irrigation installation, comparable security requirements belong in zones and the inter-zone paths need separately governed conduits; that directly resolves the requirement that assets with unlike safety and trust requirements are treated as a single flat security group despite an ISA/IEC 62443 zone-and-conduit design requirement; it is evaluated alongside the separate requirement that an already registered device was classified incorrectly and rerunning rogue rules does not change it.
D:At the large-scale irrigation installation, profiling re-evaluation acts on remaining rogues rather than automatically rewriting every registered inventory object; that directly resolves the requirement that an already registered device was classified incorrectly and rerunning rogue rules does not change it; it is evaluated alongside the separate requirement that assets with unlike safety and trust requirements are treated as a single flat security group despite an ISA/IEC 62443 zone-and-conduit design requirement.
Incorrect Answers
B:At the large-scale irrigation installation, the expected mechanism is absent because a registered endpoint is outside the ordinary rogue-only re-evaluation scope; it leaves unresolved the finding that an already registered device was classified incorrectly and rerunning rogue rules does not change it; the parallel design also has to address assets with unlike safety and trust requirements are treated as a single flat security group despite an ISA/IEC 62443 zone-and-conduit design requirement.
C:At the large-scale irrigation installation, that alternative is insufficient because switch-port documentation alone cannot establish zone trust or govern the path between different risk groups; it leaves unresolved the finding that assets with unlike safety and trust requirements are treated as a single flat security group despite an ISA/IEC 62443 zone-and-conduit design requirement; the parallel design also has to address an already registered device was classified incorrectly and rerunning rogue rules does not change it.
Question 386
An audit at the paper mill control network finds that planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network. What is the most targeted response?
- Run unrestricted vulnerability scans on every field controller during production
- Record sensors, actuators, PLCs and supervisory components by operational role
- Group systems into security zones and document controlled conduits between them
- Identify time-critical controllers and field devices and prefer passive discovery initially
Explanation
Correct Answer
D:The relevant technical distinction for the paper mill control network is that controllers and field equipment can have strict latency and availability constraints that make intrusive discovery inappropriate; that directly resolves the requirement that planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network.
Incorrect Answers
A:The mismatch at the paper mill control network is specific to the observed control requirement: indiscriminate active probing can disrupt legacy or timing-sensitive industrial endpoints; it leaves unresolved the finding that planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network.
B:At the paper mill control network, this mechanism serves the separate situation where a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization, whereas the present finding is that planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network; although recognizing field measurement, physical actuation, controller logic and supervisory functions is essential to impact analysis, the required capability remains missing.
C:At the paper mill control network, this mechanism serves the separate situation where assets with unlike safety and trust requirements are treated as a single flat security group despite an ISA/IEC 62443 zone-and-conduit design requirement, whereas the present finding is that planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network; although comparable security requirements belong in zones and the inter-zone paths need separately governed conduits, the required capability remains missing.
Question 387
An industrial network audit at the pharmaceutical production floor establishes two requirements: (1) the firewall permits an industrial TCP port but a malicious operation within that protocol remains undetected; and (2) the team sees Modbus/TCP communications and needs to constrain dangerous controller write activity while retaining read operations. What two-part implementation is the most precise response to the stated requirements?
- Use only a destination-port allow rule with no inspection profile; then treat every Modbus packet as equally safe after allowing port 502
- Use only a destination-port allow rule with no inspection profile; then design Modbus-aware operation filtering where supported at the control conduit
- Deploy network-based IPS or virtual patch protection at the applicable segment boundary; then design Modbus-aware operation filtering where supported at the control conduit
- Enable appropriate industrial-protocol IPS inspection on the matching FortiGate policy; then treat every Modbus packet as equally safe after allowing port 502
- Enable appropriate industrial-protocol IPS inspection on the matching FortiGate policy; then design Modbus-aware operation filtering where supported at the control conduit
Explanation
Correct Answer
E:The first control fits because an OT-aware IPS signature can evaluate malicious commands or exploit patterns beyond just the transport port; the second fits because Modbus function-level distinctions matter because read and write requests can share one TCP service. Together they resolve the separate findings at the pharmaceutical production floor: the firewall permits an industrial TCP port but a malicious operation within that protocol remains undetected, and the team sees Modbus/TCP communications and needs to constrain dangerous controller write activity while retaining read operations. This addresses the firewall permits an industrial TCP port but a malicious operation within that protocol remains undetected without bypassing the separate requirement that the team sees Modbus/TCP communications and needs to constrain dangerous controller write activity while retaining read operations.
Incorrect Answers
A:The first substitution fails because a transport permit has no intrinsic understanding of payload-level exploit indicators; the second fails because a common transport service does not restrict the embedded function being requested. For this pharmaceutical production floor, the first finding is that the firewall permits an industrial TCP port but a malicious operation within that protocol remains undetected, while the other is that the team sees Modbus/TCP communications and needs to constrain dangerous controller write activity while retaining read operations; neither is corrected by the chosen substitutions.
B:The second part is useful because Modbus function-level distinctions matter because read and write requests can share one TCP service; however, the first part fails because a transport permit has no intrinsic understanding of payload-level exploit indicators. The first gap remains unresolved at the pharmaceutical production floor: the firewall permits an industrial TCP port but a malicious operation within that protocol remains undetected; the second measure helps with the team sees Modbus/TCP communications and needs to constrain dangerous controller write activity while retaining read operations but cannot repair it.
C:The second action addresses the team sees Modbus/TCP communications and needs to constrain dangerous controller write activity while retaining read operations because Modbus function-level distinctions matter because read and write requests can share one TCP service, but the separate first finding still concerns the firewall permits an industrial TCP port but a malicious operation within that protocol remains undetected. The proposed first mechanism belongs to a different requirement: a plant wants to contain an exploit on a legacy PLC without installing an agent on the controller; inline network inspection can mitigate selected exploit traffic while leaving the unmodifiable endpoint software untouched, but despite the valid second control for the team sees Modbus/TCP communications and needs to constrain dangerous controller write activity while retaining read operations, it does not resolve the first finding at the pharmaceutical production floor: the firewall permits an industrial TCP port but a malicious operation within that protocol remains undetected.
D:The first action is suitable because an OT-aware IPS signature can evaluate malicious commands or exploit patterns beyond just the transport port; the second is misdirected because a common transport service does not restrict the embedded function being requested. At the pharmaceutical production floor, the remaining second gap is that the team sees Modbus/TCP communications and needs to constrain dangerous controller write activity while retaining read operations, even though the firewall permits an industrial TCP port but a malicious operation within that protocol remains undetected is covered.
Question 388
At a natural-gas compression station, engineers must address both of these documented gaps: (1) analysts must confirm that a firewall rule for an HMI to one PLC is being used rather than a broader earlier rule; and (2) existing domain sign-in information must inform access decisions without repeatedly prompting authenticated workstation users. Which TWO independently necessary controls directly fulfill the two requirements? Choose TWO.
- Examine policy order and actual policy-hit or traffic logs
- Enable more logging on the narrow rule while leaving the higher matching policy in place
- Replace user association with a static source-IP allowlist
- Evaluate Fortinet single sign-on integration and user-to-IP mappings
Explanation
Correct Answers
A:The relevant technical distinction for the natural-gas compression station is that FortiGate evaluates the applicable policy and a preceding broad match can shadow a narrow intended rule; that directly resolves the requirement that analysts must confirm that a firewall rule for an HMI to one PLC is being used rather than a broader earlier rule; it is evaluated alongside the separate requirement that existing domain sign-in information must inform access decisions without repeatedly prompting authenticated workstation users.
D:In this natural-gas compression station scenario, FSSO can make identity associations available to firewall policy when the identity source and mapping are trusted; that directly resolves the requirement that existing domain sign-in information must inform access decisions without repeatedly prompting authenticated workstation users; it is evaluated alongside the separate requirement that analysts must confirm that a firewall rule for an HMI to one PLC is being used rather than a broader earlier rule.
Incorrect Answers
B:The mismatch at the natural-gas compression station is specific to the observed control requirement: extra logging on a shadowed rule does not make traffic select that rule ahead of an earlier match; it leaves unresolved the finding that analysts must confirm that a firewall rule for an HMI to one PLC is being used rather than a broader earlier rule; the parallel design also has to address existing domain sign-in information must inform access decisions without repeatedly prompting authenticated workstation users.
C:At the natural-gas compression station, this substitutes a measure addressing a different concern: a reusable workstation address does not reliably identify the person currently signed in; it leaves unresolved the finding that existing domain sign-in information must inform access decisions without repeatedly prompting authenticated workstation users; the parallel design also has to address analysts must confirm that a firewall rule for an HMI to one PLC is being used rather than a broader earlier rule.
Question 389
A security assessment of the cold-storage automation plant records two issues: (1) inspection cannot identify a command in encrypted application traffic because only ciphertext crosses the firewall; and (2) the facility is air-gapped and cannot reach FortiGuard update servers directly. Which paired action most directly satisfies both findings without introducing an unrelated control change?
- Evaluate supported decryption or a suitable alternative inspection point within safety constraints; then open unrestricted Internet access from all controllers for signature downloads
- Evaluate supported decryption or a suitable alternative inspection point within safety constraints; then use supported manual licensing and security package transfer procedures for the offline FortiGate
- Increase the logging retention time while leaving the payload encrypted; then use supported manual licensing and security package transfer procedures for the offline FortiGate
- Enable a suitable IPS security profile on the conduit firewall policy; then use supported manual licensing and security package transfer procedures for the offline FortiGate
- Increase the logging retention time while leaving the payload encrypted; then open unrestricted Internet access from all controllers for signature downloads
Explanation
Correct Answer
B:The first control fits because a payload analyzer cannot interpret encrypted commands unless the necessary content becomes visible at a trusted point; the second fits because an air-gap deployment needs a controlled update transfer rather than assuming live FortiGuard queries. Together they resolve the separate findings at the cold-storage automation plant: inspection cannot identify a command in encrypted application traffic because only ciphertext crosses the firewall, and the facility is air-gapped and cannot reach FortiGuard update servers directly. This addresses inspection cannot identify a command in encrypted application traffic because only ciphertext crosses the firewall without bypassing the separate requirement that the facility is air-gapped and cannot reach FortiGuard update servers directly.
Incorrect Answers
A:The first action is suitable because a payload analyzer cannot interpret encrypted commands unless the necessary content becomes visible at a trusted point; the second is misdirected because exposing process devices violates the air-gap requirement and is not required for controlled package updates. At the cold-storage automation plant, the remaining second gap is that the facility is air-gapped and cannot reach FortiGuard update servers directly, even though inspection cannot identify a command in encrypted application traffic because only ciphertext crosses the firewall is covered.
C:The second part is useful because an air-gap deployment needs a controlled update transfer rather than assuming live FortiGuard queries; however, the first part fails because storing more ciphertext does not create visibility into its application-layer command. The first gap remains unresolved at the cold-storage automation plant: inspection cannot identify a command in encrypted application traffic because only ciphertext crosses the firewall; the second measure helps with the facility is air-gapped and cannot reach FortiGuard update servers directly but cannot repair it.
D:The second action addresses the facility is air-gapped and cannot reach FortiGuard update servers directly because an air-gap deployment needs a controlled update transfer rather than assuming live FortiGuard queries, but the separate first finding still concerns inspection cannot identify a command in encrypted application traffic because only ciphertext crosses the firewall. The proposed first mechanism belongs to a different requirement: the plant wants OT signatures to inspect a controller conduit but the policy has no active IPS profile; the dedicated OT attack definitions are used by IPS inspection when the service is valid and policy is configured, but despite the valid second control for the facility is air-gapped and cannot reach FortiGuard update servers directly, it does not resolve the first finding at the cold-storage automation plant: inspection cannot identify a command in encrypted application traffic because only ciphertext crosses the firewall.
E:The first substitution fails because storing more ciphertext does not create visibility into its application-layer command; the second fails because exposing process devices violates the air-gap requirement and is not required for controlled package updates. For this cold-storage automation plant, the first finding is that inspection cannot identify a command in encrypted application traffic because only ciphertext crosses the firewall, while the other is that the facility is air-gapped and cannot reach FortiGuard update servers directly; neither is corrected by the chosen substitutions.
Question 390
A targeted security validation of the automotive assembly line specifies the following: (1) controls engineers cannot patch an essential controller until the next shutdown and the risk must be accepted or mitigated formally; and (2) a FortiSIEM report is empty even though operators know incidents exist for the same week. Which paired configuration should be included in the approved OT security change?
- Document compensating controls, owner approval and a time-bound residual-risk plan; then check the report's selected data source, time range and incident filters
- Delete the vulnerability ticket once maintenance is postponed; then change the report export format without fixing the event filters
- Delete the vulnerability ticket once maintenance is postponed; then check the report's selected data source, time range and incident filters
- Document compensating controls, owner approval and a time-bound residual-risk plan; then change the report export format without fixing the event filters
Explanation
Correct Answer
A:The first control fits because deferred firmware fixes require explicit accountability and interim network controls; the second fits because reporting queries depend on correctly scoped events and normalized incident data. Together they resolve the separate findings at the automotive assembly line: controls engineers cannot patch an essential controller until the next shutdown and the risk must be accepted or mitigated formally, and a FortiSIEM report is empty even though operators know incidents exist for the same week. This addresses controls engineers cannot patch an essential controller until the next shutdown and the risk must be accepted or mitigated formally without bypassing the separate requirement that a FortiSIEM report is empty even though operators know incidents exist for the same week.
Incorrect Answers
B:The first substitution fails because closing the record without a treatment plan loses ownership of the remaining hazard; the second fails because export format does not change whether the query selects the underlying incident records. For this automotive assembly line, the first finding is that controls engineers cannot patch an essential controller until the next shutdown and the risk must be accepted or mitigated formally, while the other is that a FortiSIEM report is empty even though operators know incidents exist for the same week; neither is corrected by the chosen substitutions.
C:The second part is useful because reporting queries depend on correctly scoped events and normalized incident data; however, the first part fails because closing the record without a treatment plan loses ownership of the remaining hazard. The first gap remains unresolved at the automotive assembly line: controls engineers cannot patch an essential controller until the next shutdown and the risk must be accepted or mitigated formally; the second measure helps with a FortiSIEM report is empty even though operators know incidents exist for the same week but cannot repair it.
D:The first action is suitable because deferred firmware fixes require explicit accountability and interim network controls; the second is misdirected because export format does not change whether the query selects the underlying incident records. At the automotive assembly line, the remaining second gap is that a FortiSIEM report is empty even though operators know incidents exist for the same week, even though controls engineers cannot patch an essential controller until the next shutdown and the risk must be accepted or mitigated formally is covered.