Fortinet NSE5_FSW_AD-7.6 (Fortinet NSE 5 - FortiSwitch 7.6 Administrator) Practice Test 63

Question 620

A feature acceptance test on an access switch in routine maintenance concerns “Configure a promiscuous PVLAN port for a shared gateway.” What should be checked to establish its expected operation?

  1. Compare current FortiSwitch time with the configured schedule and observed rule counters
  2. Capture the double-tagged frame and verify distinct S-tag and customer C-tag fields
  3. Inspect gateway reachability from each secondary VLAN without direct host-to-host communication
  4. Compare captured source/destination IP fields and the rule's mask

Explanation

Correct Answer

C:

This is the precise control because the promiscuous port connects secondary VLANs to the common routed or shared service endpoint. Directly measuring that result demonstrates whether the step to provide primary-VLAN reachability to otherwise separated PVLAN hosts succeeded on an access switch in routine maintenance.

Incorrect Answers

A:

The proposed check concerns “Configure an ACL schedule” rather than “Configure a promiscuous PVLAN port for a shared gateway”: time-based ACL scheduling controls policy applicability, not the device system clock itself. For “Configure a promiscuous PVLAN port for a shared gateway” on an access switch in routine maintenance, a better test would be to inspect gateway reachability from each secondary VLAN without direct host-to-host communication, which targets provide primary-VLAN reachability to otherwise separated PVLAN hosts rather than the alternative diagnostic “Configure an ACL schedule”.

B:

This check is suited to “Use an 802.1Q QinQ outer service VLAN” when trying to transport independently numbered customer VLANs through provider infrastructure, not to verify “Configure a promiscuous PVLAN port for a shared gateway” at the training center. Checking “Configure a promiscuous PVLAN port for a shared gateway” at the training center requires evidence of its own mechanism: the promiscuous port connects secondary VLANs to the common routed or shared service endpoint; that is not the outcome measured by “Use an 802.1Q QinQ outer service VLAN”.

D:

This check is suited to “Match an ACL using an IP subnet” when trying to filter traffic from a designated routed network range, not to verify “Configure a promiscuous PVLAN port for a shared gateway” at the training center. Checking “Configure a promiscuous PVLAN port for a shared gateway” at the training center requires evidence of its own mechanism: the promiscuous port connects secondary VLANs to the common routed or shared service endpoint; that is not the outcome measured by “Match an ACL using an IP subnet”.

Question 621

During a change window in the lab, engineers are asked to transport independently numbered customer VLANs through provider infrastructure. What should they configure rather than using a feature for an adjacent purpose?

  1. Use an 802.1Q QinQ outer service VLAN
  2. Configure a protocol-based VLAN ACL where needed
  3. Install an ingress ACL for received traffic
  4. Use selective packet sampling where supported
  5. Use an ACL Ethernet-type classifier

Explanation

Correct Answer

A:

The implementation works because VLAN stacking adds an outer service tag while preserving the customer's internal VLAN identifier. This distinction is material to the lab, where the stated goal is to transport independently numbered customer VLANs through provider infrastructure.

Incorrect Answers

B:

Compared with the requested “Use an 802.1Q QinQ outer service VLAN” at the lab, this would classify a defined payload type into a separate forwarding VLAN instead: protocol classification relies on a match such as EtherType rather than every frame arriving on one physical port. At the lab, the operational proof would instead be to capture the double-tagged frame and verify distinct S-tag and customer C-tag fields, whereas “Configure a protocol-based VLAN ACL where needed” is validated by a different test: inspect protocol classifier order and the VLAN ID assigned to matching traffic.

C:

Compared with the requested “Use an 802.1Q QinQ outer service VLAN” at the lab, this would filter packets as they enter a FortiSwitch forwarding pipeline instead: an ingress ACL classifies traffic arriving at an interface and applies permitted hardware actions. At the lab, the operational proof would instead be to capture the double-tagged frame and verify distinct S-tag and customer C-tag fields, whereas “Install an ingress ACL for received traffic” is validated by a different test: review ingress ACL match counters while sending matching test frames.

D:

For the lab, “Use selective packet sampling where supported” is a different type of control from “Use an 802.1Q QinQ outer service VLAN”: sampling selects a subset of matching packets for observation while forwarding rules remain in effect. Unlike the requested feature, that setting addresses the need to gather representative traffic metadata without mirroring every packet, not the objective to transport independently numbered customer VLANs through provider infrastructure.

E:

Compared with the requested “Use an 802.1Q QinQ outer service VLAN” at the lab, this would separate IPv4, IPv6 or other Ethernet frame types in a hardware policy instead: an EtherType comparison identifies the payload protocol without relying on TCP/UDP port numbers. At the lab, the operational proof would instead be to capture the double-tagged frame and verify distinct S-tag and customer C-tag fields, whereas “Use an ACL Ethernet-type classifier” is validated by a different test: read the EtherType from the frame header and inspect the ACL service match.

Question 622

For the staging rack, an administrator applies the action “Use an 802.1Q QinQ outer service VLAN.” Which effect should appear when it operates as intended?

  1. Switch ACL classifiers, groups and counters consume finite hardware resources that can be fragmented
  2. A linked policer enforces meter behavior for the matched ACL class
  3. VLAN stacking adds an outer service tag while preserving the customer's internal VLAN identifier
  4. Isolated PVLAN ports can reach the promiscuous primary attachment but not one another

Explanation

Correct Answer

C:

Given the described goal, the configured operation is meant to transport independently numbered customer VLANs through provider infrastructure. The most relevant validation is to capture the double-tagged frame and verify distinct S-tag and customer C-tag fields for the equipment at the staging rack.

Incorrect Answers

A:

That behavior applies when engineers “Review the ACL hardware resource usage”; the different operation “Use an 802.1Q QinQ outer service VLAN” is intended to transport independently numbered customer VLANs through provider infrastructure. That different feature is verified by inspect ACL usage and available hardware entries before changing rule order; for “Use an 802.1Q QinQ outer service VLAN” on a recently upgraded FortiSwitch, the relevant evidence is to capture the double-tagged frame and verify distinct S-tag and customer C-tag fields.

B:

That behavior applies when engineers “Apply an ACL policer to matching frames”; the different operation “Use an 802.1Q QinQ outer service VLAN” is intended to transport independently numbered customer VLANs through provider infrastructure. That different feature is verified by inspect policer conformance/excess statistics alongside ACL counters; for “Use an 802.1Q QinQ outer service VLAN” on a recently upgraded FortiSwitch, the relevant evidence is to capture the double-tagged frame and verify distinct S-tag and customer C-tag fields.

D:

This outcome would be relevant to “Apply an isolated secondary PVLAN for tenant servers” at the staging rack, not the task “Use an 802.1Q QinQ outer service VLAN”; the other task is to allow server access to a shared gateway while blocking any host-to-host communication. The action “Use an 802.1Q QinQ outer service VLAN” targets a different result: VLAN stacking adds an outer service tag while preserving the customer's internal VLAN identifier; the proposed alternative would instead be checked by test server-to-gateway reachability and server-to-server isolation within the isolated VLAN.

Question 623

On a FortiLink-managed access switch at the research building, the team reports that it has configured “Use an 802.1Q QinQ outer service VLAN.” Which verification provides the strongest direct evidence that the intended function is working?

  1. Capture the double-tagged frame and verify distinct S-tag and customer C-tag fields
  2. Inspect gateway reachability from each secondary VLAN without direct host-to-host communication
  3. Inspect egress ACL counters for the relevant outgoing port
  4. Inspect ACL match counters and resulting QoS queue handling

Explanation

Correct Answer

A:

The switch behavior that matters is: VLAN stacking adds an outer service tag while preserving the customer's internal VLAN identifier. Directly measuring that result demonstrates whether the step to transport independently numbered customer VLANs through provider infrastructure succeeded on a FortiLink-managed access switch.

Incorrect Answers

B:

This check is suited to “Configure a promiscuous PVLAN port for a shared gateway” when trying to provide primary-VLAN reachability to otherwise separated PVLAN hosts, not to verify “Use an 802.1Q QinQ outer service VLAN” at the research building. Checking “Use an 802.1Q QinQ outer service VLAN” at the research building requires evidence of its own mechanism: VLAN stacking adds an outer service tag while preserving the customer's internal VLAN identifier; that is not the outcome measured by “Configure a promiscuous PVLAN port for a shared gateway”.

C:

The proposed check concerns “Install an egress ACL for outgoing traffic” rather than “Use an 802.1Q QinQ outer service VLAN”: an egress-stage policy acts on frames being transmitted rather than their original entry classification. For “Use an 802.1Q QinQ outer service VLAN” on a FortiLink-managed access switch, a better test would be to capture the double-tagged frame and verify distinct S-tag and customer C-tag fields, which targets transport independently numbered customer VLANs through provider infrastructure rather than the alternative diagnostic “Install an egress ACL for outgoing traffic”.

D:

This check is suited to “Apply a QoS action using an ACL” when trying to prioritize a defined class without requiring every endpoint to mark itself, not to verify “Use an 802.1Q QinQ outer service VLAN” at the research building. Checking “Use an 802.1Q QinQ outer service VLAN” at the research building requires evidence of its own mechanism: VLAN stacking adds an outer service tag while preserving the customer's internal VLAN identifier; that is not the outcome measured by “Apply a QoS action using an ACL”.

Question 624

For the clinic, the network team needs to classify a defined payload type into a separate forwarding VLAN. Which change is the most direct way to implement that requirement on a switch linked to a FortiGate running FortiOS 7.6?

  1. Match a FortiSwitch ACL by source MAC address
  2. Configure a protocol-based VLAN ACL where needed
  3. Apply a community secondary PVLAN to one workgroup
  4. Drop matched unwanted frames with an ACL action

Explanation

Correct Answer

B:

At this network boundary, protocol classification relies on a match such as EtherType rather than every frame arriving on one physical port. The operator can test this claim by the specific check: inspect protocol classifier order and the VLAN ID assigned to matching traffic.

Incorrect Answers

A:

Compared with the requested “Configure a protocol-based VLAN ACL where needed” at the clinic, this would limit an Ethernet policy to frames from a specific hardware address instead: the layer-2 source MAC classifier selects packets by the originating address at the configured ACL stage. At the clinic, the operational proof would instead be to inspect protocol classifier order and the VLAN ID assigned to matching traffic, whereas “Match a FortiSwitch ACL by source MAC address” is validated by a different test: compare the captured Ethernet source address with the ACL match value.

C:

For the clinic, “Apply a community secondary PVLAN to one workgroup” is a different type of control from “Configure a protocol-based VLAN ACL where needed”: community PVLAN members can communicate with their own community and the promiscuous primary port. Unlike the requested feature, that setting addresses the need to allow peers within one designated group to communicate but isolate them from other groups, not the objective to classify a defined payload type into a separate forwarding VLAN.

D:

Compared with the requested “Configure a protocol-based VLAN ACL where needed” at the clinic, this would block a targeted source or protocol using explicit hardware filtering instead: a drop action discards frames meeting the ACL match rather than disabling the whole physical port. At the clinic, the operational proof would instead be to inspect protocol classifier order and the VLAN ID assigned to matching traffic, whereas “Drop matched unwanted frames with an ACL action” is validated by a different test: confirm matching test packets are counted and discarded while unrelated traffic still passes.

Question 625

On a central switching stack, “Configure a protocol-based VLAN ACL where needed” is configured for the data hall. What effect should an administrator expect without assuming unrelated features are enabled?

  1. VLAN stacking adds an outer service tag while preserving the customer's internal VLAN identifier
  2. Protocol classification relies on a match such as EtherType rather than every frame arriving on one physical port
  3. A prelookup ACL applies available classifiers at its pipeline stage; it is not a route-table entry
  4. A linked policer enforces meter behavior for the matched ACL class
  5. Sampling selects a subset of matching packets for observation while forwarding rules remain in effect

Explanation

Correct Answer

B:

In this deployment, the configured operation is meant to classify a defined payload type into a separate forwarding VLAN. The most relevant validation is to inspect protocol classifier order and the VLAN ID assigned to matching traffic for the equipment at the data hall.

Incorrect Answers

A:

This outcome would be relevant to “Use an 802.1Q QinQ outer service VLAN” at the data hall, not the task “Configure a protocol-based VLAN ACL where needed”; the other task is to transport independently numbered customer VLANs through provider infrastructure. The action “Configure a protocol-based VLAN ACL where needed” targets a different result: protocol classification relies on a match such as EtherType rather than every frame arriving on one physical port; the proposed alternative would instead be checked by capture the double-tagged frame and verify distinct S-tag and customer C-tag fields.

C:

That behavior applies when engineers “Use prelookup ACL classification”; the different operation “Configure a protocol-based VLAN ACL where needed” is intended to classify a defined payload type into a separate forwarding VLAN. That different feature is verified by check prelookup stage configuration and rule-use counters; for “Configure a protocol-based VLAN ACL where needed” on a central switching stack, the relevant evidence is to inspect protocol classifier order and the VLAN ID assigned to matching traffic.

D:

That behavior applies when engineers “Apply an ACL policer to matching frames”; the different operation “Configure a protocol-based VLAN ACL where needed” is intended to classify a defined payload type into a separate forwarding VLAN. That different feature is verified by inspect policer conformance/excess statistics alongside ACL counters; for “Configure a protocol-based VLAN ACL where needed” on a central switching stack, the relevant evidence is to inspect protocol classifier order and the VLAN ID assigned to matching traffic.

E:

That behavior applies when engineers “Use selective packet sampling where supported”; the different operation “Configure a protocol-based VLAN ACL where needed” is intended to classify a defined payload type into a separate forwarding VLAN. That different feature is verified by check the sampling configuration and resulting observed packet frequency; for “Configure a protocol-based VLAN ACL where needed” on a central switching stack, the relevant evidence is to inspect protocol classifier order and the VLAN ID assigned to matching traffic.

Question 626

A post-change review at the warehouse must validate the implementation of “Configure a protocol-based VLAN ACL where needed.” What should the reviewer inspect first?

  1. Compare current FortiSwitch time with the configured schedule and observed rule counters
  2. Inspect protocol classifier order and the VLAN ID assigned to matching traffic
  3. Compare captured source/destination IP fields and the rule's mask
  4. Inspect ACL usage and available hardware entries before changing rule order

Explanation

Correct Answer

B:

For the stated requirement, protocol classification relies on a match such as EtherType rather than every frame arriving on one physical port. Directly measuring that result demonstrates whether the step to classify a defined payload type into a separate forwarding VLAN succeeded on a FortiSwitch connected to the security edge.

Incorrect Answers

A:

This check is suited to “Configure an ACL schedule” when trying to enforce a selected match/action only during approved operational hours, not to verify “Configure a protocol-based VLAN ACL where needed” at the warehouse. Checking “Configure a protocol-based VLAN ACL where needed” at the warehouse requires evidence of its own mechanism: protocol classification relies on a match such as EtherType rather than every frame arriving on one physical port; that is not the outcome measured by “Configure an ACL schedule”.

C:

The proposed check concerns “Match an ACL using an IP subnet” rather than “Configure a protocol-based VLAN ACL where needed”: an IP source or destination prefix classifier restricts the match to packets meeting the configured address condition. For “Configure a protocol-based VLAN ACL where needed” on a FortiSwitch connected to the security edge, a better test would be to inspect protocol classifier order and the VLAN ID assigned to matching traffic, which targets classify a defined payload type into a separate forwarding VLAN rather than the alternative diagnostic “Match an ACL using an IP subnet”.

D:

This check is suited to “Review the ACL hardware resource usage” when trying to diagnose rejection of additional switch ACL entries despite apparently valid syntax, not to verify “Configure a protocol-based VLAN ACL where needed” at the warehouse. Checking “Configure a protocol-based VLAN ACL where needed” at the warehouse requires evidence of its own mechanism: protocol classification relies on a match such as EtherType rather than every frame arriving on one physical port; that is not the outcome measured by “Review the ACL hardware resource usage”.

Question 627

On an access switch in routine maintenance in the headquarters, the next task is to keep a known endpoint's traffic on an assigned segment when moved among permitted ports. What is the appropriate configuration decision?

  1. Keep ACL group priority ordering consistent
  2. Apply a QoS action using an ACL
  3. Configure a protocol-based VLAN ACL where needed
  4. Use a MAC-based VLAN security association

Explanation

Correct Answer

D:

The deciding detail is that MAC-to-VLAN mapping is based on source identity and differs from general ACL drop actions. This distinction is material to the headquarters, where the stated goal is to keep a known endpoint's traffic on an assigned segment when moved among permitted ports.

Incorrect Answers

A:

Compared with the requested “Use a MAC-based VLAN security association” at the headquarters, this would resolve conflicting actions when several ACL groups match the same packet instead: for conflicting group actions, the lower-numbered ACL group has higher action priority. At the headquarters, the operational proof would instead be to compare the source MAC with the VLAN-assignment entry and effective port VLAN membership, whereas “Keep ACL group priority ordering consistent” is validated by a different test: inspect matching rules by ACL group and compare their group numbers.

B:

Compared with the requested “Use a MAC-based VLAN security association” at the headquarters, this would prioritize a defined class without requiring every endpoint to mark itself instead: ACL actions can assign supported classification or priority treatment to matching frames. At the headquarters, the operational proof would instead be to compare the source MAC with the VLAN-assignment entry and effective port VLAN membership, whereas “Apply a QoS action using an ACL” is validated by a different test: inspect ACL match counters and resulting QoS queue handling.

C:

For the headquarters, “Configure a protocol-based VLAN ACL where needed” is a different type of control from “Use a MAC-based VLAN security association”: protocol classification relies on a match such as EtherType rather than every frame arriving on one physical port. Unlike the requested feature, that setting addresses the need to classify a defined payload type into a separate forwarding VLAN, not the objective to keep a known endpoint's traffic on an assigned segment when moved among permitted ports.

Question 628

For the hospital wing, an administrator applies the action “Use a MAC-based VLAN security association.” Which effect should appear when it operates as intended?

  1. MAC-to-VLAN mapping is based on source identity and differs from general ACL drop actions
  2. Community PVLAN members can communicate with their own community and the promiscuous primary port
  3. An ingress ACL classifies traffic arriving at an interface and applies permitted hardware actions
  4. Sampling selects a subset of matching packets for observation while forwarding rules remain in effect
  5. An EtherType comparison identifies the payload protocol without relying on TCP/UDP port numbers

Explanation

Correct Answer

A:

The relevant mechanism is: the configured operation is meant to keep a known endpoint's traffic on an assigned segment when moved among permitted ports. The most relevant validation is to compare the source MAC with the VLAN-assignment entry and effective port VLAN membership for the equipment at the hospital wing.

Incorrect Answers

B:

That behavior applies when engineers “Apply a community secondary PVLAN to one workgroup”; the different operation “Use a MAC-based VLAN security association” is intended to keep a known endpoint's traffic on an assigned segment when moved among permitted ports. That different feature is verified by test peer reachability inside the community and deny a connection to a different community; for “Use a MAC-based VLAN security association” on a managed campus switch, the relevant evidence is to compare the source MAC with the VLAN-assignment entry and effective port VLAN membership.

C:

This outcome would be relevant to “Install an ingress ACL for received traffic” at the hospital wing, not the task “Use a MAC-based VLAN security association”; the other task is to filter packets as they enter a FortiSwitch forwarding pipeline. The action “Use a MAC-based VLAN security association” targets a different result: MAC-to-VLAN mapping is based on source identity and differs from general ACL drop actions; the proposed alternative would instead be checked by review ingress ACL match counters while sending matching test frames.

D:

That behavior applies when engineers “Use selective packet sampling where supported”; the different operation “Use a MAC-based VLAN security association” is intended to keep a known endpoint's traffic on an assigned segment when moved among permitted ports. That different feature is verified by check the sampling configuration and resulting observed packet frequency; for “Use a MAC-based VLAN security association” on a managed campus switch, the relevant evidence is to compare the source MAC with the VLAN-assignment entry and effective port VLAN membership.

E:

That behavior applies when engineers “Use an ACL Ethernet-type classifier”; the different operation “Use a MAC-based VLAN security association” is intended to keep a known endpoint's traffic on an assigned segment when moved among permitted ports. That different feature is verified by read the EtherType from the frame header and inspect the ACL service match; for “Use a MAC-based VLAN security association” on a managed campus switch, the relevant evidence is to compare the source MAC with the VLAN-assignment entry and effective port VLAN membership.

Question 629

The accepted design for the training center requires the ability to diagnose rejection of additional switch ACL entries despite apparently valid syntax. Which switch feature is the closest fit?

  1. Apply a QoS action using an ACL
  2. Keep ACL group priority ordering consistent
  3. Review the ACL hardware resource usage
  4. Configure a protocol-based VLAN ACL where needed

Explanation

Correct Answer

C:

This approach fits because switch ACL classifiers, groups and counters consume finite hardware resources that can be fragmented. This distinction is material to the training center, where the stated goal is to diagnose rejection of additional switch ACL entries despite apparently valid syntax.

Incorrect Answers

A:

Compared with the requested “Review the ACL hardware resource usage” at the training center, this would prioritize a defined class without requiring every endpoint to mark itself instead: ACL actions can assign supported classification or priority treatment to matching frames. At the training center, the operational proof would instead be to inspect ACL usage and available hardware entries before changing rule order, whereas “Apply a QoS action using an ACL” is validated by a different test: inspect ACL match counters and resulting QoS queue handling.

B:

Compared with the requested “Review the ACL hardware resource usage” at the training center, this would resolve conflicting actions when several ACL groups match the same packet instead: for conflicting group actions, the lower-numbered ACL group has higher action priority. At the training center, the operational proof would instead be to inspect ACL usage and available hardware entries before changing rule order, whereas “Keep ACL group priority ordering consistent” is validated by a different test: inspect matching rules by ACL group and compare their group numbers.

D:

For the training center, “Configure a protocol-based VLAN ACL where needed” is a different type of control from “Review the ACL hardware resource usage”: protocol classification relies on a match such as EtherType rather than every frame arriving on one physical port. Unlike the requested feature, that setting addresses the need to classify a defined payload type into a separate forwarding VLAN, not the objective to diagnose rejection of additional switch ACL entries despite apparently valid syntax.

Question 630

A change record for a FortiLink-managed access switch states “Review the ACL hardware resource usage.” Which description correctly explains what this will accomplish?

  1. An ingress ACL classifies traffic arriving at an interface and applies permitted hardware actions
  2. Community PVLAN members can communicate with their own community and the promiscuous primary port
  3. An EtherType comparison identifies the payload protocol without relying on TCP/UDP port numbers
  4. Switch ACL classifiers, groups and counters consume finite hardware resources that can be fragmented

Explanation

Correct Answer

D:

The critical distinction is that the configured operation is meant to diagnose rejection of additional switch ACL entries despite apparently valid syntax. The most relevant validation is to inspect ACL usage and available hardware entries before changing rule order for the equipment at the lab.

Incorrect Answers

A:

This outcome would be relevant to “Install an ingress ACL for received traffic” at the lab, not the task “Review the ACL hardware resource usage”; the other task is to filter packets as they enter a FortiSwitch forwarding pipeline. The action “Review the ACL hardware resource usage” targets a different result: switch ACL classifiers, groups and counters consume finite hardware resources that can be fragmented; the proposed alternative would instead be checked by review ingress ACL match counters while sending matching test frames.

B:

That behavior applies when engineers “Apply a community secondary PVLAN to one workgroup”; the different operation “Review the ACL hardware resource usage” is intended to diagnose rejection of additional switch ACL entries despite apparently valid syntax. That different feature is verified by test peer reachability inside the community and deny a connection to a different community; for “Review the ACL hardware resource usage” on a FortiLink-managed access switch, the relevant evidence is to inspect ACL usage and available hardware entries before changing rule order.

C:

That behavior applies when engineers “Use an ACL Ethernet-type classifier”; the different operation “Review the ACL hardware resource usage” is intended to diagnose rejection of additional switch ACL entries despite apparently valid syntax. That different feature is verified by read the EtherType from the frame header and inspect the ACL service match; for “Review the ACL hardware resource usage” on a FortiLink-managed access switch, the relevant evidence is to inspect ACL usage and available hardware entries before changing rule order.

Fortinet NSE 5 - FortiSwitch 7.6 Administrator (NSE5_FSW_AD-7.6) Practice Tests