Fortinet NSE5_FSW_AD-7.6 (Fortinet NSE 5 - FortiSwitch 7.6 Administrator) Practice Test 65

Question 640

An administrator responsible for a managed switch running FortiSwitchOS 7.6 in the media studio must monitor source traffic from another switch across a VLAN transport path. Which configuration best matches that precise goal?

  1. Create a packet capture profile with a filter
  2. Configure a local SPAN mirror
  3. Configure an RSPAN remote mirror
  4. Choose ingress mirroring for arriving frames

Explanation

Correct Answer

C:

The relevant mechanism is: RSPAN carries mirrored Ethernet traffic over an appropriate remote mirror VLAN. The operator can test this claim by the specific check: inspect RSPAN VLAN membership on intermediate trunks and packets arriving at the remote analyzer.

Incorrect Answers

A:

For the media studio, “Create a packet capture profile with a filter” is a different type of control from “Configure an RSPAN remote mirror”: a capture profile defines the observed interface and packet selection before capture starts. Unlike the requested feature, that setting addresses the need to limit local FortiSwitch capture to packets relevant to a particular troubleshooting investigation, not the objective to monitor source traffic from another switch across a VLAN transport path.

B:

Compared with the requested “Configure an RSPAN remote mirror” at the media studio, this would send copies of a source port's traffic to a diagnostic port on the same switch instead: SPAN duplicates selected ingress or egress traffic locally for a connected analyzer. At the media studio, the operational proof would instead be to inspect RSPAN VLAN membership on intermediate trunks and packets arriving at the remote analyzer, whereas “Configure a local SPAN mirror” is validated by a different test: inspect the configured mirror source/destination and analyzer's received frames.

D:

Compared with the requested “Configure an RSPAN remote mirror” at the media studio, this would diagnose whether a switch receives packets before its forwarding decisions instead: ingress mirror direction copies traffic entering the selected interface. At the media studio, the operational proof would instead be to inspect RSPAN VLAN membership on intermediate trunks and packets arriving at the remote analyzer, whereas “Choose ingress mirroring for arriving frames” is validated by a different test: verify the source packet is visible on ingress even when later filtering prevents forwarding.

Question 641

An operations log records this activity at the retail site: configure an RSPAN remote mirror. Which result is specifically attributable to that action?

  1. RSPAN carries mirrored Ethernet traffic over an appropriate remote mirror VLAN
  2. Ingress mirror direction copies traffic entering the selected interface
  3. A capture profile defines the observed interface and packet selection before capture starts
  4. SPAN duplicates selected ingress or egress traffic locally for a connected analyzer

Explanation

Correct Answer

A:

This approach fits because the configured operation is meant to monitor source traffic from another switch across a VLAN transport path. The most relevant validation is to inspect RSPAN VLAN membership on intermediate trunks and packets arriving at the remote analyzer for the equipment at the retail site.

Incorrect Answers

B:

That behavior applies when engineers “Choose ingress mirroring for arriving frames”; the different operation “Configure an RSPAN remote mirror” is intended to monitor source traffic from another switch across a VLAN transport path. That different feature is verified by verify the source packet is visible on ingress even when later filtering prevents forwarding; for “Configure an RSPAN remote mirror” on a remote FortiSwitch installation, the relevant evidence is to inspect RSPAN VLAN membership on intermediate trunks and packets arriving at the remote analyzer.

C:

That behavior applies when engineers “Create a packet capture profile with a filter”; the different operation “Configure an RSPAN remote mirror” is intended to monitor source traffic from another switch across a VLAN transport path. That different feature is verified by review captured headers and verify the chosen filter matches the targeted flow; for “Configure an RSPAN remote mirror” on a remote FortiSwitch installation, the relevant evidence is to inspect RSPAN VLAN membership on intermediate trunks and packets arriving at the remote analyzer.

D:

This outcome would be relevant to “Configure a local SPAN mirror” at the retail site, not the task “Configure an RSPAN remote mirror”; the other task is to send copies of a source port's traffic to a diagnostic port on the same switch. The action “Configure an RSPAN remote mirror” targets a different result: RSPAN carries mirrored Ethernet traffic over an appropriate remote mirror VLAN; the proposed alternative would instead be checked by inspect the configured mirror source/destination and analyzer's received frames.

Question 642

After implementing “Configure an RSPAN remote mirror,” the site engineer needs to assess its actual effect on an endpoint-facing FortiSwitch port. Which test is the best match?

  1. Review captured headers and verify the chosen filter matches the targeted flow
  2. Inspect the configured mirror source/destination and analyzer's received frames
  3. Inspect RSPAN VLAN membership on intermediate trunks and packets arriving at the remote analyzer
  4. Verify the source packet is visible on ingress even when later filtering prevents forwarding

Explanation

Correct Answer

C:

The critical distinction is that RSPAN carries mirrored Ethernet traffic over an appropriate remote mirror VLAN. Directly measuring that result demonstrates whether the step to monitor source traffic from another switch across a VLAN transport path succeeded on an endpoint-facing FortiSwitch port.

Incorrect Answers

A:

This check is suited to “Create a packet capture profile with a filter” when trying to limit local FortiSwitch capture to packets relevant to a particular troubleshooting investigation, not to verify “Configure an RSPAN remote mirror” at the airport office. Checking “Configure an RSPAN remote mirror” at the airport office requires evidence of its own mechanism: RSPAN carries mirrored Ethernet traffic over an appropriate remote mirror VLAN; that is not the outcome measured by “Create a packet capture profile with a filter”.

B:

The proposed check concerns “Configure a local SPAN mirror” rather than “Configure an RSPAN remote mirror”: SPAN duplicates selected ingress or egress traffic locally for a connected analyzer. For “Configure an RSPAN remote mirror” on an endpoint-facing FortiSwitch port, a better test would be to inspect RSPAN VLAN membership on intermediate trunks and packets arriving at the remote analyzer, which targets monitor source traffic from another switch across a VLAN transport path rather than the alternative diagnostic “Configure a local SPAN mirror”.

D:

This check is suited to “Choose ingress mirroring for arriving frames” when trying to diagnose whether a switch receives packets before its forwarding decisions, not to verify “Configure an RSPAN remote mirror” at the airport office. Checking “Configure an RSPAN remote mirror” at the airport office requires evidence of its own mechanism: RSPAN carries mirrored Ethernet traffic over an appropriate remote mirror VLAN; that is not the outcome measured by “Choose ingress mirroring for arriving frames”.

Question 643

A peer review of the operations center asks how the design will send mirrored traffic to a collector reached across a routed network. Which FortiSwitch technique is the correct response?

  1. Create a packet capture profile with a filter
  2. Configure a local SPAN mirror
  3. Check packet capture storage and profile capacity
  4. Choose ingress mirroring for arriving frames
  5. Configure an ERSPAN mirror for an IP-reachable analyzer

Explanation

Correct Answer

E:

That setting is appropriate here because ERSPAN encapsulates mirrored frames for transport over an IP network to a remote destination. This distinction is material to the operations center, where the stated goal is to send mirrored traffic to a collector reached across a routed network.

Incorrect Answers

A:

Compared with the requested “Configure an ERSPAN mirror for an IP-reachable analyzer” at the operations center, this would limit local FortiSwitch capture to packets relevant to a particular troubleshooting investigation instead: a capture profile defines the observed interface and packet selection before capture starts. At the operations center, the operational proof would instead be to check routed collector reachability and ERSPAN encapsulation on arriving packets, whereas “Create a packet capture profile with a filter” is validated by a different test: review captured headers and verify the chosen filter matches the targeted flow.

B:

For the operations center, “Configure a local SPAN mirror” is a different type of control from “Configure an ERSPAN mirror for an IP-reachable analyzer”: SPAN duplicates selected ingress or egress traffic locally for a connected analyzer. Unlike the requested feature, that setting addresses the need to send copies of a source port's traffic to a diagnostic port on the same switch, not the objective to send mirrored traffic to a collector reached across a routed network.

C:

Compared with the requested “Configure an ERSPAN mirror for an IP-reachable analyzer” at the operations center, this would avoid losing captures on a busy switch with limited capture resources instead: switch model determines capture-profile capacity and RAM-disk space for retained packets. At the operations center, the operational proof would instead be to check routed collector reachability and ERSPAN encapsulation on arriving packets, whereas “Check packet capture storage and profile capacity” is validated by a different test: inspect capture file size, platform allocation and whether the profile can still record.

D:

Compared with the requested “Configure an ERSPAN mirror for an IP-reachable analyzer” at the operations center, this would diagnose whether a switch receives packets before its forwarding decisions instead: ingress mirror direction copies traffic entering the selected interface. At the operations center, the operational proof would instead be to check routed collector reachability and ERSPAN encapsulation on arriving packets, whereas “Choose ingress mirroring for arriving frames” is validated by a different test: verify the source packet is visible on ingress even when later filtering prevents forwarding.

Question 644

A change record for a newly commissioned floor switch states “Configure an ERSPAN mirror for an IP-reachable analyzer.” Which description correctly explains what this will accomplish?

  1. SPAN duplicates selected ingress or egress traffic locally for a connected analyzer
  2. Ingress mirror direction copies traffic entering the selected interface
  3. Switch model determines capture-profile capacity and RAM-disk space for retained packets
  4. ERSPAN encapsulates mirrored frames for transport over an IP network to a remote destination

Explanation

Correct Answer

D:

This is the precise control because the configured operation is meant to send mirrored traffic to a collector reached across a routed network. The most relevant validation is to check routed collector reachability and ERSPAN encapsulation on arriving packets for the equipment at the warehouse.

Incorrect Answers

A:

That behavior applies when engineers “Configure a local SPAN mirror”; the different operation “Configure an ERSPAN mirror for an IP-reachable analyzer” is intended to send mirrored traffic to a collector reached across a routed network. That different feature is verified by inspect the configured mirror source/destination and analyzer's received frames; for “Configure an ERSPAN mirror for an IP-reachable analyzer” on a newly commissioned floor switch, the relevant evidence is to check routed collector reachability and ERSPAN encapsulation on arriving packets.

B:

This outcome would be relevant to “Choose ingress mirroring for arriving frames” at the warehouse, not the task “Configure an ERSPAN mirror for an IP-reachable analyzer”; the other task is to diagnose whether a switch receives packets before its forwarding decisions. The action “Configure an ERSPAN mirror for an IP-reachable analyzer” targets a different result: ERSPAN encapsulates mirrored frames for transport over an IP network to a remote destination; the proposed alternative would instead be checked by verify the source packet is visible on ingress even when later filtering prevents forwarding.

C:

That behavior applies when engineers “Check packet capture storage and profile capacity”; the different operation “Configure an ERSPAN mirror for an IP-reachable analyzer” is intended to send mirrored traffic to a collector reached across a routed network. That different feature is verified by inspect capture file size, platform allocation and whether the profile can still record; for “Configure an ERSPAN mirror for an IP-reachable analyzer” on a newly commissioned floor switch, the relevant evidence is to check routed collector reachability and ERSPAN encapsulation on arriving packets.

Question 645

At the headquarters, a dashboard shows ordinary link-up state, but the team also needs proof for “Configure an ERSPAN mirror for an IP-reachable analyzer.” Which targeted check should be used?

  1. Inspect the configured mirror source/destination and analyzer's received frames
  2. Verify the source packet is visible on ingress even when later filtering prevents forwarding
  3. Check routed collector reachability and ERSPAN encapsulation on arriving packets
  4. Inspect capture file size, platform allocation and whether the profile can still record

Explanation

Correct Answer

C:

The implementation works because ERSPAN encapsulates mirrored frames for transport over an IP network to a remote destination. Directly measuring that result demonstrates whether the step to send mirrored traffic to a collector reached across a routed network succeeded on a local switch administering branch clients.

Incorrect Answers

A:

This check is suited to “Configure a local SPAN mirror” when trying to send copies of a source port's traffic to a diagnostic port on the same switch, not to verify “Configure an ERSPAN mirror for an IP-reachable analyzer” at the headquarters. Checking “Configure an ERSPAN mirror for an IP-reachable analyzer” at the headquarters requires evidence of its own mechanism: ERSPAN encapsulates mirrored frames for transport over an IP network to a remote destination; that is not the outcome measured by “Configure a local SPAN mirror”.

B:

The proposed check concerns “Choose ingress mirroring for arriving frames” rather than “Configure an ERSPAN mirror for an IP-reachable analyzer”: ingress mirror direction copies traffic entering the selected interface. For “Configure an ERSPAN mirror for an IP-reachable analyzer” on a local switch administering branch clients, a better test would be to check routed collector reachability and ERSPAN encapsulation on arriving packets, which targets send mirrored traffic to a collector reached across a routed network rather than the alternative diagnostic “Choose ingress mirroring for arriving frames”.

D:

This check is suited to “Check packet capture storage and profile capacity” when trying to avoid losing captures on a busy switch with limited capture resources, not to verify “Configure an ERSPAN mirror for an IP-reachable analyzer” at the headquarters. Checking “Configure an ERSPAN mirror for an IP-reachable analyzer” at the headquarters requires evidence of its own mechanism: ERSPAN encapsulates mirrored frames for transport over an IP network to a remote destination; that is not the outcome measured by “Check packet capture storage and profile capacity”.

Question 646

A production incident in the hospital wing reveals the need to diagnose whether a switch receives packets before its forwarding decisions. Which targeted FortiSwitch setting or method should the team use?

  1. Choose ingress mirroring for arriving frames
  2. Configure a local SPAN mirror
  3. Create a packet capture profile with a filter
  4. Choose egress mirroring for leaving frames

Explanation

Correct Answer

A:

Given the described goal, ingress mirror direction copies traffic entering the selected interface. The operator can test this claim by the specific check: verify the source packet is visible on ingress even when later filtering prevents forwarding.

Incorrect Answers

B:

Compared with the requested “Choose ingress mirroring for arriving frames” at the hospital wing, this would send copies of a source port's traffic to a diagnostic port on the same switch instead: SPAN duplicates selected ingress or egress traffic locally for a connected analyzer. At the hospital wing, the operational proof would instead be to verify the source packet is visible on ingress even when later filtering prevents forwarding, whereas “Configure a local SPAN mirror” is validated by a different test: inspect the configured mirror source/destination and analyzer's received frames.

C:

Compared with the requested “Choose ingress mirroring for arriving frames” at the hospital wing, this would limit local FortiSwitch capture to packets relevant to a particular troubleshooting investigation instead: a capture profile defines the observed interface and packet selection before capture starts. At the hospital wing, the operational proof would instead be to verify the source packet is visible on ingress even when later filtering prevents forwarding, whereas “Create a packet capture profile with a filter” is validated by a different test: review captured headers and verify the chosen filter matches the targeted flow.

D:

For the hospital wing, “Choose egress mirroring for leaving frames” is a different type of control from “Choose ingress mirroring for arriving frames”: egress mirror direction observes packets chosen for output after relevant forwarding steps. Unlike the requested feature, that setting addresses the need to confirm which frames the switch actually transmits toward a downstream device, not the objective to diagnose whether a switch receives packets before its forwarding decisions.

Question 647

A colleague asks about the effect of “Choose ingress mirroring for arriving frames” on a production FortiSwitch fabric. Which behavior best characterizes that feature?

  1. Ingress mirror direction copies traffic entering the selected interface
  2. A capture profile defines the observed interface and packet selection before capture starts
  3. Egress mirror direction observes packets chosen for output after relevant forwarding steps
  4. SPAN duplicates selected ingress or egress traffic locally for a connected analyzer
  5. RSPAN carries mirrored Ethernet traffic over an appropriate remote mirror VLAN

Explanation

Correct Answer

A:

The switch behavior that matters is: the configured operation is meant to diagnose whether a switch receives packets before its forwarding decisions. The most relevant validation is to verify the source packet is visible on ingress even when later filtering prevents forwarding for the equipment at the factory.

Incorrect Answers

B:

This outcome would be relevant to “Create a packet capture profile with a filter” at the factory, not the task “Choose ingress mirroring for arriving frames”; the other task is to limit local FortiSwitch capture to packets relevant to a particular troubleshooting investigation. The action “Choose ingress mirroring for arriving frames” targets a different result: ingress mirror direction copies traffic entering the selected interface; the proposed alternative would instead be checked by review captured headers and verify the chosen filter matches the targeted flow.

C:

That behavior applies when engineers “Choose egress mirroring for leaving frames”; the different operation “Choose ingress mirroring for arriving frames” is intended to diagnose whether a switch receives packets before its forwarding decisions. That different feature is verified by compare the analyzer's egress trace with destination port counters; for “Choose ingress mirroring for arriving frames” on a production FortiSwitch fabric, the relevant evidence is to verify the source packet is visible on ingress even when later filtering prevents forwarding.

D:

That behavior applies when engineers “Configure a local SPAN mirror”; the different operation “Choose ingress mirroring for arriving frames” is intended to diagnose whether a switch receives packets before its forwarding decisions. That different feature is verified by inspect the configured mirror source/destination and analyzer's received frames; for “Choose ingress mirroring for arriving frames” on a production FortiSwitch fabric, the relevant evidence is to verify the source packet is visible on ingress even when later filtering prevents forwarding.

E:

That behavior applies when engineers “Configure an RSPAN remote mirror”; the different operation “Choose ingress mirroring for arriving frames” is intended to diagnose whether a switch receives packets before its forwarding decisions. That different feature is verified by inspect RSPAN VLAN membership on intermediate trunks and packets arriving at the remote analyzer; for “Choose ingress mirroring for arriving frames” on a production FortiSwitch fabric, the relevant evidence is to verify the source packet is visible on ingress even when later filtering prevents forwarding.

Question 648

The change-control ticket for a newly racked distribution unit requires one validation of the goal to diagnose whether a switch receives packets before its forwarding decisions. Which evidence should be collected?

  1. Verify the source packet is visible on ingress even when later filtering prevents forwarding
  2. Inspect the configured mirror source/destination and analyzer's received frames
  3. Compare the analyzer's egress trace with destination port counters
  4. Review captured headers and verify the chosen filter matches the targeted flow

Explanation

Correct Answer

A:

At this network boundary, ingress mirror direction copies traffic entering the selected interface. Directly measuring that result demonstrates whether the step to diagnose whether a switch receives packets before its forwarding decisions succeeded on a newly racked distribution unit.

Incorrect Answers

B:

This check is suited to “Configure a local SPAN mirror” when trying to send copies of a source port's traffic to a diagnostic port on the same switch, not to verify “Choose ingress mirroring for arriving frames” at the distribution floor. Checking “Choose ingress mirroring for arriving frames” at the distribution floor requires evidence of its own mechanism: ingress mirror direction copies traffic entering the selected interface; that is not the outcome measured by “Configure a local SPAN mirror”.

C:

This check is suited to “Choose egress mirroring for leaving frames” when trying to confirm which frames the switch actually transmits toward a downstream device, not to verify “Choose ingress mirroring for arriving frames” at the distribution floor. Checking “Choose ingress mirroring for arriving frames” at the distribution floor requires evidence of its own mechanism: ingress mirror direction copies traffic entering the selected interface; that is not the outcome measured by “Choose egress mirroring for leaving frames”.

D:

The proposed check concerns “Create a packet capture profile with a filter” rather than “Choose ingress mirroring for arriving frames”: a capture profile defines the observed interface and packet selection before capture starts. For “Choose ingress mirroring for arriving frames” on a newly racked distribution unit, a better test would be to verify the source packet is visible on ingress even when later filtering prevents forwarding, which targets diagnose whether a switch receives packets before its forwarding decisions rather than the alternative diagnostic “Create a packet capture profile with a filter”.

Question 649

The operational requirement for two distribution switches at the media studio is to confirm which frames the switch actually transmits toward a downstream device. Which FortiSwitch choice directly targets it?

  1. Create a packet capture profile with a filter
  2. Choose egress mirroring for leaving frames
  3. Choose ingress mirroring for arriving frames
  4. Configure an RSPAN remote mirror

Explanation

Correct Answer

B:

In this deployment, egress mirror direction observes packets chosen for output after relevant forwarding steps. This distinction is material to the media studio, where the stated goal is to confirm which frames the switch actually transmits toward a downstream device.

Incorrect Answers

A:

Compared with the requested “Choose egress mirroring for leaving frames” at the media studio, this would limit local FortiSwitch capture to packets relevant to a particular troubleshooting investigation instead: a capture profile defines the observed interface and packet selection before capture starts. At the media studio, the operational proof would instead be to compare the analyzer's egress trace with destination port counters, whereas “Create a packet capture profile with a filter” is validated by a different test: review captured headers and verify the chosen filter matches the targeted flow.

C:

Compared with the requested “Choose egress mirroring for leaving frames” at the media studio, this would diagnose whether a switch receives packets before its forwarding decisions instead: ingress mirror direction copies traffic entering the selected interface. At the media studio, the operational proof would instead be to compare the analyzer's egress trace with destination port counters, whereas “Choose ingress mirroring for arriving frames” is validated by a different test: verify the source packet is visible on ingress even when later filtering prevents forwarding.

D:

For the media studio, “Configure an RSPAN remote mirror” is a different type of control from “Choose egress mirroring for leaving frames”: RSPAN carries mirrored Ethernet traffic over an appropriate remote mirror VLAN. Unlike the requested feature, that setting addresses the need to monitor source traffic from another switch across a VLAN transport path, not the objective to confirm which frames the switch actually transmits toward a downstream device.

Question 650

When engineers choose egress mirroring for leaving frames at the retail site, which forwarding, security, management or diagnostic outcome follows from that action?

  1. A CLI sniffer can display or collect matching packets without installing a permanent forwarding rule
  2. Ingress mirror direction copies traffic entering the selected interface
  3. A capture profile defines the observed interface and packet selection before capture starts
  4. Egress mirror direction observes packets chosen for output after relevant forwarding steps
  5. RSPAN carries mirrored Ethernet traffic over an appropriate remote mirror VLAN

Explanation

Correct Answer

D:

For the stated requirement, the configured operation is meant to confirm which frames the switch actually transmits toward a downstream device. The most relevant validation is to compare the analyzer's egress trace with destination port counters for the equipment at the retail site.

Incorrect Answers

A:

That behavior applies when engineers “Run an appropriate FortiSwitch sniffer command”; the different operation “Choose egress mirroring for leaving frames” is intended to confirm which frames the switch actually transmits toward a downstream device. That different feature is verified by repeat the transaction and confirm the expected frame types appear in sniffer output; for “Choose egress mirroring for leaving frames” on a staging FortiSwitch, the relevant evidence is to compare the analyzer's egress trace with destination port counters.

B:

This outcome would be relevant to “Choose ingress mirroring for arriving frames” at the retail site, not the task “Choose egress mirroring for leaving frames”; the other task is to diagnose whether a switch receives packets before its forwarding decisions. The action “Choose egress mirroring for leaving frames” targets a different result: egress mirror direction observes packets chosen for output after relevant forwarding steps; the proposed alternative would instead be checked by verify the source packet is visible on ingress even when later filtering prevents forwarding.

C:

That behavior applies when engineers “Create a packet capture profile with a filter”; the different operation “Choose egress mirroring for leaving frames” is intended to confirm which frames the switch actually transmits toward a downstream device. That different feature is verified by review captured headers and verify the chosen filter matches the targeted flow; for “Choose egress mirroring for leaving frames” on a staging FortiSwitch, the relevant evidence is to compare the analyzer's egress trace with destination port counters.

E:

That behavior applies when engineers “Configure an RSPAN remote mirror”; the different operation “Choose egress mirroring for leaving frames” is intended to confirm which frames the switch actually transmits toward a downstream device. That different feature is verified by inspect RSPAN VLAN membership on intermediate trunks and packets arriving at the remote analyzer; for “Choose egress mirroring for leaving frames” on a staging FortiSwitch, the relevant evidence is to compare the analyzer's egress trace with destination port counters.

Fortinet NSE 5 - FortiSwitch 7.6 Administrator (NSE5_FSW_AD-7.6) Practice Tests