Question 10
At the rail signaling depot, the next change must address the fact that the FortiGate knows an asset's vulnerability but its flow bypasses the firewall policy bearing the virtual patching profile. The proposed shortcut is to expand the dashboard widget while leaving the routing bypass. Which alternative should the architect approve instead?
- Expand the dashboard widget while leaving the routing bypass
- Define and test the severity and action choices within a virtual patching profile
- Put the profile on the real traffic path through a matching firewall policy
- Review device-level and signature-level exemption lists before assuming signature failure
Explanation
Correct Answer
C:In this rail signaling depot scenario, a policy-attached virtual patch is not effective for traffic that does not cross that policy; that directly resolves the requirement that the FortiGate knows an asset's vulnerability but its flow bypasses the firewall policy bearing the virtual patching profile.
Incorrect Answers
A:At the rail signaling depot, this substitutes a measure addressing a different concern: dashboard presentation cannot force bypassing sessions through a mitigation point; it leaves unresolved the finding that the FortiGate knows an asset's vulnerability but its flow bypasses the firewall policy bearing the virtual patching profile.
B:At the rail signaling depot, this mechanism serves the separate situation where the security engineer must decide which severity levels are actively blocked and which are only logged, whereas the present finding is that the FortiGate knows an asset's vulnerability but its flow bypasses the firewall policy bearing the virtual patching profile; although profile-level action and severity selections set which matched mitigations are enforced versus observed, the required capability remains missing.
D:At the rail signaling depot, this mechanism serves the separate situation where a virtual patching exemption has been configured for a known device and its expected mitigation is not applied, whereas the present finding is that the FortiGate knows an asset's vulnerability but its flow bypasses the firewall policy bearing the virtual patching profile; although an exempted MAC or rule can intentionally skip otherwise applicable virtual patching checks, the required capability remains missing.
Question 11
During a maintenance-window design exercise for the wind-farm collector substation, the team notes: (1) a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization; and (2) OT and IoT signatures are inadvertently excluded from the detection configuration on a FortiGate interface. What is the technically justified combination for the two separate observations?
- Record sensors, actuators, PLCs and supervisory components by operational role; then increase general traffic logging while leaving OT signature categories excluded
- Classify all equipment as interchangeable Ethernet endpoints; then increase general traffic logging while leaving OT signature categories excluded
- Record sensors, actuators, PLCs and supervisory components by operational role; then review the interface signature-exclusion settings for OT and IoT discovery
- Classify all equipment as interchangeable Ethernet endpoints; then review the interface signature-exclusion settings for OT and IoT discovery
Explanation
Correct Answer
C:The first control fits because recognizing field measurement, physical actuation, controller logic and supervisory functions is essential to impact analysis; the second fits because excluded signature categories suppress matching for those device types and reduce available asset details. Together they resolve the separate findings at the wind-farm collector substation: a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization, and OT and IoT signatures are inadvertently excluded from the detection configuration on a FortiGate interface. This addresses a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization without bypassing the separate requirement that OT and IoT signatures are inadvertently excluded from the detection configuration on a FortiGate interface.
Incorrect Answers
A:The first action is suitable because recognizing field measurement, physical actuation, controller logic and supervisory functions is essential to impact analysis; the second is misdirected because more log records cannot re-enable detection categories explicitly excluded at the interface. At the wind-farm collector substation, the remaining second gap is that OT and IoT signatures are inadvertently excluded from the detection configuration on a FortiGate interface, even though a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization is covered.
B:The first substitution fails because a generic network label obscures who senses, controls or merely displays industrial processes; the second fails because more log records cannot re-enable detection categories explicitly excluded at the interface. For this wind-farm collector substation, the first finding is that a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization, while the other is that OT and IoT signatures are inadvertently excluded from the detection configuration on a FortiGate interface; neither is corrected by the chosen substitutions.
D:The second part is useful because excluded signature categories suppress matching for those device types and reduce available asset details; however, the first part fails because a generic network label obscures who senses, controls or merely displays industrial processes. The first gap remains unresolved at the wind-farm collector substation: a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization; the second measure helps with OT and IoT signatures are inadvertently excluded from the detection configuration on a FortiGate interface but cannot repair it.
Question 12
At the industrial refrigeration installation, the next change must address the fact that an IPS profile logs detections but the plant's approved response requires blocking a specifically validated malicious signature. What is the most targeted response?
- Change the report title from alert to blocked
- Deploy network-based IPS or virtual patch protection at the applicable segment boundary
- Remove that unnecessary service from the segment's firewall allowlist
- Change the relevant signature action under a tested IPS profile and policy
Explanation
Correct Answer
D:The relevant technical distinction for the industrial refrigeration installation is that alert-only inspection provides visibility whereas a validated block action can stop matched traffic in-path; that directly resolves the requirement that an IPS profile logs detections but the plant's approved response requires blocking a specifically validated malicious signature.
Incorrect Answers
A:The mismatch at the industrial refrigeration installation is specific to the observed control requirement: a display label cannot turn a logging-only IPS action into enforcement; it leaves unresolved the finding that an IPS profile logs detections but the plant's approved response requires blocking a specifically validated malicious signature.
B:At the industrial refrigeration installation, this mechanism serves the separate situation where a plant wants to contain an exploit on a legacy PLC without installing an agent on the controller, whereas the present finding is that an IPS profile logs detections but the plant's approved response requires blocking a specifically validated malicious signature; although inline network inspection can mitigate selected exploit traffic while leaving the unmodifiable endpoint software untouched, the required capability remains missing.
C:At the industrial refrigeration installation, this mechanism serves the separate situation where the OT architect needs to reduce the attack surface of a specific protocol service that is not required by the process, whereas the present finding is that an IPS profile logs detections but the plant's approved response requires blocking a specifically validated malicious signature; although eliminating unneeded permitted services shrinks reachable attack paths independently of signature coverage, the required capability remains missing.
Question 13
At an automated packaging warehouse, engineers must address both of these documented gaps: (1) a validated OT incident needs controlled notification to on-call analysts rather than a silent dashboard entry; and (2) the SOC observes a planned controller reboot and must prevent an unnecessary availability incident only during the approved window. Which TWO independently necessary controls directly fulfill the two requirements? Choose TWO.
- Suppress all future loss-of-connectivity notifications for the entire site
- Configure the associated incident or event notification channel and recipient routing
- Schedule a next-day report instead of configuring timely event notifications
- Adjust precise handler conditions and expected maintenance exceptions with review
- Add a time-bounded rule exception for the known maintenance condition
Explanation
Correct Answers
B:In this automated packaging warehouse scenario, alerts have operational value only when they reach the accountable responder with sufficient context; that directly resolves the requirement that a validated OT incident needs controlled notification to on-call analysts rather than a silent dashboard entry; it is evaluated alongside the separate requirement that the SOC observes a planned controller reboot and must prevent an unnecessary availability incident only during the approved window.
E:For the stated gap at the automated packaging warehouse, scoped exceptions reduce predictable false alarms without permanently removing the rule; that directly resolves the requirement that the SOC observes a planned controller reboot and must prevent an unnecessary availability incident only during the approved window; it is evaluated alongside the separate requirement that a validated OT incident needs controlled notification to on-call analysts rather than a silent dashboard entry.
Incorrect Answers
A:At the automated packaging warehouse, that alternative is insufficient because blanket suppression conceals unexpected controller failures outside the maintenance window; it leaves unresolved the finding that the SOC observes a planned controller reboot and must prevent an unnecessary availability incident only during the approved window; the parallel design also has to address a validated OT incident needs controlled notification to on-call analysts rather than a silent dashboard entry.
C:At the automated packaging warehouse, this substitutes a measure addressing a different concern: a periodic report does not route the qualifying incident to an on-call responder when it fires; it leaves unresolved the finding that a validated OT incident needs controlled notification to on-call analysts rather than a silent dashboard entry; the parallel design also has to address the SOC observes a planned controller reboot and must prevent an unnecessary availability incident only during the approved window.
D:At the automated packaging warehouse, this mechanism serves the separate situation where event-volume spikes after a maintenance operation are obscuring genuine OT incidents, whereas the present finding is that a validated OT incident needs controlled notification to on-call analysts rather than a silent dashboard entry; although narrowly reasoned filters reduce known benign matches while retaining significant detections, the required capability remains missing.
Question 14
A technician reviewing security evidence from the regional pipeline control center finds that the site needs a view of its industrial cyber exposure rather than only general office endpoint hygiene. What is the most targeted response?
- Use only general IT vulnerability totals without industrial asset exposure context
- Review the OT Security Risk report and validate its source data and scope
- Document compensating controls, owner approval and a time-bound residual-risk plan
- Combine KEV information with asset exposure and process consequence
Explanation
Correct Answer
B:For the stated gap at the regional pipeline control center, an OT-focused report frames industrial devices and risks in terms useful for plant-specific prioritization; that directly resolves the requirement that the site needs a view of its industrial cyber exposure rather than only general office endpoint hygiene.
Incorrect Answers
A:At the regional pipeline control center, that alternative is insufficient because generic IT totals can overlook the exposure and operational consequence of specific controllers; it leaves unresolved the finding that the site needs a view of its industrial cyber exposure rather than only general office endpoint hygiene.
C:At the regional pipeline control center, this mechanism serves the separate situation where controls engineers cannot patch an essential controller until the next shutdown and the risk must be accepted or mitigated formally, whereas the present finding is that the site needs a view of its industrial cyber exposure rather than only general office endpoint hygiene; although deferred firmware fixes require explicit accountability and interim network controls, the required capability remains missing.
D:At the regional pipeline control center, this mechanism serves the separate situation where security staff need to focus on weaknesses that are actively exploited rather than treating all listed vulnerabilities alike, whereas the present finding is that the site needs a view of its industrial cyber exposure rather than only general office endpoint hygiene; although exploitation intelligence becomes useful when tied to real device reachability and safety impact, the required capability remains missing.
Question 15
Before the semiconductor fabrication facility accepts a proposed OT security architecture, it must demonstrate: (1) the OT team cannot tell which industrial asset provided the source IP of a detected threat; and (2) a vulnerability widget shows an OT weakness but the analyst needs to prioritize those known to be exploited in the wild. Which two measures correctly map to the operational and security requirements?
- Associate firewall events with resolved device identity and asset attributes; then review the KEV indicators associated with the discovered asset vulnerability
- Associate firewall events with resolved device identity and asset attributes; then rank vulnerabilities by a generic severity score without examining KEV status
- Integrate Fortinet Security Fabric telemetry and inventory across the OT boundary; then review the KEV indicators associated with the discovered asset vulnerability
- Remove source identity fields from the SIEM ingest pipeline; then review the KEV indicators associated with the discovered asset vulnerability
- Remove source identity fields from the SIEM ingest pipeline; then rank vulnerabilities by a generic severity score without examining KEV status
Explanation
Correct Answer
A:The first control fits because enriched asset-to-IP associations make events actionable for specific controllers instead of only transient addresses; the second fits because known-exploited-vulnerability context differentiates observed exploitation relevance from an undifferentiated list of weaknesses. Together they resolve the separate findings at the semiconductor fabrication facility: the OT team cannot tell which industrial asset provided the source IP of a detected threat, and a vulnerability widget shows an OT weakness but the analyst needs to prioritize those known to be exploited in the wild. This addresses the OT team cannot tell which industrial asset provided the source IP of a detected threat without bypassing the separate requirement that a vulnerability widget shows an OT weakness but the analyst needs to prioritize those known to be exploited in the wild.
Incorrect Answers
B:The first action is suitable because enriched asset-to-IP associations make events actionable for specific controllers instead of only transient addresses; the second is misdirected because severity-only ordering omits the exploited-in-the-wild evidence explicitly required by the analyst. At the semiconductor fabrication facility, the remaining second gap is that a vulnerability widget shows an OT weakness but the analyst needs to prioritize those known to be exploited in the wild, even though the OT team cannot tell which industrial asset provided the source IP of a detected threat is covered.
C:The second action addresses a vulnerability widget shows an OT weakness but the analyst needs to prioritize those known to be exploited in the wild because known-exploited-vulnerability context differentiates observed exploitation relevance from an undifferentiated list of weaknesses, but the separate first finding still concerns the OT team cannot tell which industrial asset provided the source IP of a detected threat. The proposed first mechanism belongs to a different requirement: multiple Fortinet components provide partial OT visibility but incidents cannot be related across firewall, asset and analytics data; correlation of FortiGate enforcement, device identity and analytics observations supports a coordinated OT security view, but despite the valid second control for a vulnerability widget shows an OT weakness but the analyst needs to prioritize those known to be exploited in the wild, it does not resolve the first finding at the semiconductor fabrication facility: the OT team cannot tell which industrial asset provided the source IP of a detected threat.
D:The second part is useful because known-exploited-vulnerability context differentiates observed exploitation relevance from an undifferentiated list of weaknesses; however, the first part fails because discarding device identity prevents analysts from relating alerts to the affected industrial asset. The first gap remains unresolved at the semiconductor fabrication facility: the OT team cannot tell which industrial asset provided the source IP of a detected threat; the second measure helps with a vulnerability widget shows an OT weakness but the analyst needs to prioritize those known to be exploited in the wild but cannot repair it.
E:The first substitution fails because discarding device identity prevents analysts from relating alerts to the affected industrial asset; the second fails because severity-only ordering omits the exploited-in-the-wild evidence explicitly required by the analyst. For this semiconductor fabrication facility, the first finding is that the OT team cannot tell which industrial asset provided the source IP of a detected threat, while the other is that a vulnerability widget shows an OT weakness but the analyst needs to prioritize those known to be exploited in the wild; neither is corrected by the chosen substitutions.
Question 16
The wastewater pumping station is preparing a controlled rollout. One outstanding requirement is that a Purdue model diagram does not show which cross-level flows the firewall actually governs. The proposed shortcut is to place all firewall inspection only on workstation loopback traffic. Which alternative should the architect approve instead?
- Evaluate virtual domains with separate routing and policy contexts
- Place FortiGate policy boundaries at identified inter-zone conduits
- Place all firewall inspection only on workstation loopback traffic
- Collect telemetry through approved segmented collectors and controlled boundary paths
Explanation
Correct Answer
B:The relevant technical distinction for the wastewater pumping station is that a firewall at the conduit can enforce narrowly permitted communication between distinct Purdue-related zones; that directly resolves the requirement that a Purdue model diagram does not show which cross-level flows the firewall actually governs.
Incorrect Answers
A:At the wastewater pumping station, this mechanism serves the separate situation where a site wants independent policy administration and traffic isolation for separate industrial tenants on the same FortiGate, whereas the present finding is that a Purdue model diagram does not show which cross-level flows the firewall actually governs; although VDOMs provide logical separation of firewall configuration and forwarding contexts on a shared FortiGate, the required capability remains missing.
C:The mismatch at the wastewater pumping station is specific to the observed control requirement: local workstation inspection cannot enforce communications crossing separate industrial zones; it leaves unresolved the finding that a Purdue model diagram does not show which cross-level flows the firewall actually governs.
D:At the wastewater pumping station, this mechanism serves the separate situation where sensors at a process-control layer must be visible to the SOC without exposing those sensors directly to the enterprise LAN, whereas the present finding is that a Purdue model diagram does not show which cross-level flows the firewall actually governs; although controlled information flows preserve OT segmentation while supplying analysis outside sensitive control segments, the required capability remains missing.
Question 17
An industrial network audit at the municipal water-treatment facility establishes two requirements: (1) the security engineer must decide which severity levels are actively blocked and which are only logged; and (2) IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries. Which plan provides the needed control for each finding rather than a superficial substitute?
- Define and test the severity and action choices within a virtual patching profile; then define strictly scoped IEC 104 conduit policies consistent with authorized SCADA peers
- Increase traffic logging while leaving virtual-patching severity actions unchanged; then expose IEC 104 services to any routable corporate address
- Increase traffic logging while leaving virtual-patching severity actions unchanged; then define strictly scoped IEC 104 conduit policies consistent with authorized SCADA peers
- Define and test the severity and action choices within a virtual patching profile; then expose IEC 104 services to any routable corporate address
Explanation
Correct Answer
A:The first control fits because profile-level action and severity selections set which matched mitigations are enforced versus observed; the second fits because telemetry protocol awareness and peer restrictions reduce exposure of the substation interface. Together they resolve the separate findings at the municipal water-treatment facility: the security engineer must decide which severity levels are actively blocked and which are only logged, and IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries. This addresses the security engineer must decide which severity levels are actively blocked and which are only logged without bypassing the separate requirement that IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries.
Incorrect Answers
B:The first substitution fails because extra visibility does not configure which virtual-patching severities should block a session; the second fails because broad routed availability violates the small set of approved SCADA relationships. For this municipal water-treatment facility, the first finding is that the security engineer must decide which severity levels are actively blocked and which are only logged, while the other is that IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries; neither is corrected by the chosen substitutions.
C:The second part is useful because telemetry protocol awareness and peer restrictions reduce exposure of the substation interface; however, the first part fails because extra visibility does not configure which virtual-patching severities should block a session. The first gap remains unresolved at the municipal water-treatment facility: the security engineer must decide which severity levels are actively blocked and which are only logged; the second measure helps with IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries but cannot repair it.
D:The first action is suitable because profile-level action and severity selections set which matched mitigations are enforced versus observed; the second is misdirected because broad routed availability violates the small set of approved SCADA relationships. At the municipal water-treatment facility, the remaining second gap is that IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries, even though the security engineer must decide which severity levels are actively blocked and which are only logged is covered.
Question 18
Before the district water pumping plant accepts a proposed OT security architecture, it must demonstrate: (1) an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions; and (2) a FortiAnalyzer OT detection must trigger a predefined review or quarantine workflow without a human manually exporting logs. Which proposal would pass both acceptance tests with the fewest irrelevant changes?
- Identify DNP3 traffic using its industrial protocol context and configured communications pattern; then rely on a monthly static report as the only response trigger
- Distinguish necessary cyclic industrial communications from unnecessary management or engineering access; then connect a validated event handler to a controlled automation response
- Identify DNP3 traffic using its industrial protocol context and configured communications pattern; then connect a validated event handler to a controlled automation response
- Apply a generic HTTP-only parsing assumption to DNP3 events; then rely on a monthly static report as the only response trigger
- Apply a generic HTTP-only parsing assumption to DNP3 events; then connect a validated event handler to a controlled automation response
Explanation
Correct Answer
C:The first control fits because DNP3 supports telemetry and control exchanges that require different baselines from web browsing; the second fits because event-driven response can feed an approved containment action from the detection context. Together they resolve the separate findings at the district water pumping plant: an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions, and a FortiAnalyzer OT detection must trigger a predefined review or quarantine workflow without a human manually exporting logs. This addresses an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions without bypassing the separate requirement that a FortiAnalyzer OT detection must trigger a predefined review or quarantine workflow without a human manually exporting logs.
Incorrect Answers
A:The first action is suitable because DNP3 supports telemetry and control exchanges that require different baselines from web browsing; the second is misdirected because scheduled historical reporting does not provide event-driven containment. At the district water pumping plant, the remaining second gap is that a FortiAnalyzer OT detection must trigger a predefined review or quarantine workflow without a human manually exporting logs, even though an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions is covered.
B:The second action addresses a FortiAnalyzer OT detection must trigger a predefined review or quarantine workflow without a human manually exporting logs because event-driven response can feed an approved containment action from the detection context, but the separate first finding still concerns an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions. The proposed first mechanism belongs to a different requirement: EtherNet/IP controller exchanges are allowed but an uncontrolled engineering port still exposes programming capabilities; EtherNet/IP operational traffic and configuration reachability can require different security treatment, but despite the valid second control for a FortiAnalyzer OT detection must trigger a predefined review or quarantine workflow without a human manually exporting logs, it does not resolve the first finding at the district water pumping plant: an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions.
D:The first substitution fails because a web request parser does not describe DNP3 operational functions or expected field-device messages; the second fails because scheduled historical reporting does not provide event-driven containment. For this district water pumping plant, the first finding is that an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions, while the other is that a FortiAnalyzer OT detection must trigger a predefined review or quarantine workflow without a human manually exporting logs; neither is corrected by the chosen substitutions.
E:The second part is useful because event-driven response can feed an approved containment action from the detection context; however, the first part fails because a web request parser does not describe DNP3 operational functions or expected field-device messages. The first gap remains unresolved at the district water pumping plant: an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions; the second measure helps with a FortiAnalyzer OT detection must trigger a predefined review or quarantine workflow without a human manually exporting logs but cannot repair it.
Question 19
An OT architect reviewing the electric distribution substation observes two independent gaps: (1) investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile; and (2) the team expects current device vulnerability mappings after new FortiGuard definitions are issued. Which plan provides the needed control for each finding rather than a superficial substitute?
- Examine both firewall traffic action logs and security-profile event details; then determine whether policy-compatible TLS deep inspection is possible for the affected flow
- Examine both firewall traffic action logs and security-profile event details; then check valid update connectivity or the approved offline package update path
- Deploy network-based IPS or virtual patch protection at the applicable segment boundary; then check valid update connectivity or the approved offline package update path
- Examine only source and destination addresses without inspecting security-event action fields; then depend on firmware uptime to make signatures self-update
- Examine both firewall traffic action logs and security-profile event details; then depend on firmware uptime to make signatures self-update
- Examine only source and destination addresses without inspecting security-event action fields; then check valid update connectivity or the approved offline package update path
Explanation
Correct Answer
B:The first control fits because session policy decisions and IPS or application detections are different observations requiring correlation; the second fits because local signature and vulnerability intelligence must be refreshed through an authorized update workflow. Together they resolve the separate findings at the electric distribution substation: investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile, and the team expects current device vulnerability mappings after new FortiGuard definitions are issued. This addresses investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile without bypassing the separate requirement that the team expects current device vulnerability mappings after new FortiGuard definitions are issued.
Incorrect Answers
A:The first control responds to investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile because session policy decisions and IPS or application detections are different observations requiring correlation, but the separate second finding still concerns the team expects current device vulnerability mappings after new FortiGuard definitions are issued. The second measure targets a different requirement: the engineer must inspect virtual patch coverage on TLS-protected traffic and payload inspection is absent; encrypted application data may need approved decryption before payload-based mitigations can match, whereas the current second finding is that the team expects current device vulnerability mappings after new FortiGuard definitions are issued, with the different first requirement being investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile.
C:The second action addresses the team expects current device vulnerability mappings after new FortiGuard definitions are issued because local signature and vulnerability intelligence must be refreshed through an authorized update workflow, but the separate first finding still concerns investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile. The proposed first mechanism belongs to a different requirement: a plant wants to contain an exploit on a legacy PLC without installing an agent on the controller; inline network inspection can mitigate selected exploit traffic while leaving the unmodifiable endpoint software untouched, but despite the valid second control for the team expects current device vulnerability mappings after new FortiGuard definitions are issued, it does not resolve the first finding at the electric distribution substation: investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile.
D:The first substitution fails because endpoint addressing cannot reveal whether the blocking decision came from policy matching or IPS; the second fails because elapsed running time is not a mechanism for acquiring new threat definitions. For this electric distribution substation, the first finding is that investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile, while the other is that the team expects current device vulnerability mappings after new FortiGuard definitions are issued; neither is corrected by the chosen substitutions.
E:The first action is suitable because session policy decisions and IPS or application detections are different observations requiring correlation; the second is misdirected because elapsed running time is not a mechanism for acquiring new threat definitions. At the electric distribution substation, the remaining second gap is that the team expects current device vulnerability mappings after new FortiGuard definitions are issued, even though investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile is covered.
F:The second part is useful because local signature and vulnerability intelligence must be refreshed through an authorized update workflow; however, the first part fails because endpoint addressing cannot reveal whether the blocking decision came from policy matching or IPS. The first gap remains unresolved at the electric distribution substation: investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile; the second measure helps with the team expects current device vulnerability mappings after new FortiGuard definitions are issued but cannot repair it.
Question 20
Following a joint IT/OT risk review at the automotive assembly line, two required changes emerge: (1) a technician can log in to a portal but cannot reach a required PLC because the effective network policy lacks that destination; and (2) a registered workstation failed its compliance policy scan but must receive only remediation access. Which plan provides the needed control for each finding rather than a superficial substitute?
- Inspect the authenticated user's group and matching firewall policy scope; then treat every failed posture scan as a successful normal registration
- Keep resetting the technician's second factor without checking authorization; then treat every failed posture scan as a successful normal registration
- Inspect the authenticated user's group and matching firewall policy scope; then apply FortiNAC forced remediation and the remediation isolation state
- Keep resetting the technician's second factor without checking authorization; then apply FortiNAC forced remediation and the remediation isolation state
Explanation
Correct Answer
C:The first control fits because successful authentication does not itself grant every destination and service; authorization is evaluated separately; the second fits because untrusted registered hosts can be restricted until their compliance posture is corrected. Together they resolve the separate findings at the automotive assembly line: a technician can log in to a portal but cannot reach a required PLC because the effective network policy lacks that destination, and a registered workstation failed its compliance policy scan but must receive only remediation access. This addresses a technician can log in to a portal but cannot reach a required PLC because the effective network policy lacks that destination without bypassing the separate requirement that a registered workstation failed its compliance policy scan but must receive only remediation access.
Incorrect Answers
A:The first action is suitable because successful authentication does not itself grant every destination and service; authorization is evaluated separately; the second is misdirected because registration status does not mean a device still meets the required security posture. At the automotive assembly line, the remaining second gap is that a registered workstation failed its compliance policy scan but must receive only remediation access, even though a technician can log in to a portal but cannot reach a required PLC because the effective network policy lacks that destination is covered.
B:The first substitution fails because factor enrollment does not change a missing destination or service permission; the second fails because registration status does not mean a device still meets the required security posture. For this automotive assembly line, the first finding is that a technician can log in to a portal but cannot reach a required PLC because the effective network policy lacks that destination, while the other is that a registered workstation failed its compliance policy scan but must receive only remediation access; neither is corrected by the chosen substitutions.
D:The second part is useful because untrusted registered hosts can be restricted until their compliance posture is corrected; however, the first part fails because factor enrollment does not change a missing destination or service permission. The first gap remains unresolved at the automotive assembly line: a technician can log in to a portal but cannot reach a required PLC because the effective network policy lacks that destination; the second measure helps with a registered workstation failed its compliance policy scan but must receive only remediation access but cannot repair it.