Fortinet NSE6_OTS_AR-7.6 (Fortinet NSE 6 - OT Security 7.6 Architect) Practice Test 27

Question 260

The plant cybersecurity team at the petrochemical blending plant has two narrowly scoped objectives: (1) the OT VLAN design is complete but traffic can still traverse a permissive routed interface between the VLANs; and (2) a registered workstation failed its compliance policy scan but must receive only remediation access. Which two measures correctly map to the operational and security requirements?

  1. Add explicit inter-VLAN firewall policy at the routing boundary; then treat every failed posture scan as a successful normal registration
  2. Create more descriptive VLAN names and keep the router unrestricted; then apply FortiNAC forced remediation and the remediation isolation state
  3. Add explicit inter-VLAN firewall policy at the routing boundary; then apply FortiNAC forced remediation and the remediation isolation state
  4. Create more descriptive VLAN names and keep the router unrestricted; then treat every failed posture scan as a successful normal registration

Explanation

Correct Answer

C:

The first control fits because separate layer-two membership does not automatically prevent routed communication through an allowed path; the second fits because untrusted registered hosts can be restricted until their compliance posture is corrected. Together they resolve the separate findings at the petrochemical blending plant: the OT VLAN design is complete but traffic can still traverse a permissive routed interface between the VLANs, and a registered workstation failed its compliance policy scan but must receive only remediation access. This addresses the OT VLAN design is complete but traffic can still traverse a permissive routed interface between the VLANs without bypassing the separate requirement that a registered workstation failed its compliance policy scan but must receive only remediation access.

Incorrect Answers

A:

The first action is suitable because separate layer-two membership does not automatically prevent routed communication through an allowed path; the second is misdirected because registration status does not mean a device still meets the required security posture. At the petrochemical blending plant, the remaining second gap is that a registered workstation failed its compliance policy scan but must receive only remediation access, even though the OT VLAN design is complete but traffic can still traverse a permissive routed interface between the VLANs is covered.

B:

The second part is useful because untrusted registered hosts can be restricted until their compliance posture is corrected; however, the first part fails because naming network segments changes no layer-three authorization decisions. The first gap remains unresolved at the petrochemical blending plant: the OT VLAN design is complete but traffic can still traverse a permissive routed interface between the VLANs; the second measure helps with a registered workstation failed its compliance policy scan but must receive only remediation access but cannot repair it.

D:

The first substitution fails because naming network segments changes no layer-three authorization decisions; the second fails because registration status does not mean a device still meets the required security posture. For this petrochemical blending plant, the first finding is that the OT VLAN design is complete but traffic can still traverse a permissive routed interface between the VLANs, while the other is that a registered workstation failed its compliance policy scan but must receive only remediation access; neither is corrected by the chosen substitutions.

Question 261

A security assessment of the semiconductor fabrication facility records two issues: (1) investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile; and (2) the SOC wants to verify that an exploit was mitigated by the intended protection policy rather than by endpoint downtime. Which paired configuration should be included in the approved OT security change?

  1. Examine both firewall traffic action logs and security-profile event details; then correlate threat action, policy identity and reachability evidence during a safe validation
  2. Examine only source and destination addresses without inspecting security-event action fields; then infer successful virtual patching from the absence of all traffic
  3. Examine only source and destination addresses without inspecting security-event action fields; then correlate threat action, policy identity and reachability evidence during a safe validation
  4. Examine both firewall traffic action logs and security-profile event details; then infer successful virtual patching from the absence of all traffic

Explanation

Correct Answer

A:

The first control fits because session policy decisions and IPS or application detections are different observations requiring correlation; the second fits because documented policy hits and blocked detections distinguish intended mitigation from an unavailable controller. Together they resolve the separate findings at the semiconductor fabrication facility: investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile, and the SOC wants to verify that an exploit was mitigated by the intended protection policy rather than by endpoint downtime. This addresses investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile without bypassing the separate requirement that the SOC wants to verify that an exploit was mitigated by the intended protection policy rather than by endpoint downtime.

Incorrect Answers

B:

The first substitution fails because endpoint addressing cannot reveal whether the blocking decision came from policy matching or IPS; the second fails because an idle or disconnected endpoint can produce silence even when the mitigation is not configured. For this semiconductor fabrication facility, the first finding is that investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile, while the other is that the SOC wants to verify that an exploit was mitigated by the intended protection policy rather than by endpoint downtime; neither is corrected by the chosen substitutions.

C:

The second part is useful because documented policy hits and blocked detections distinguish intended mitigation from an unavailable controller; however, the first part fails because endpoint addressing cannot reveal whether the blocking decision came from policy matching or IPS. The first gap remains unresolved at the semiconductor fabrication facility: investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile; the second measure helps with the SOC wants to verify that an exploit was mitigated by the intended protection policy rather than by endpoint downtime but cannot repair it.

D:

The first action is suitable because session policy decisions and IPS or application detections are different observations requiring correlation; the second is misdirected because an idle or disconnected endpoint can produce silence even when the mitigation is not configured. At the semiconductor fabrication facility, the remaining second gap is that the SOC wants to verify that an exploit was mitigated by the intended protection policy rather than by endpoint downtime, even though investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile is covered.

Question 262

A technician reviewing security evidence from the electric distribution substation finds that a North American electric utility needs to relate its cyber-system inventory and perimeter protections to the applicable NERC CIP obligations. The proposed shortcut is to use only a general IT security score without identifying BES Cyber Systems. Which alternative should the architect approve instead?

  1. Use only a general IT security score without identifying BES Cyber Systems
  2. Define zone-specific security requirements and assess the conduits connecting them
  3. Map the plant's functions to the Purdue model before defining security boundaries
  4. Identify applicable BES Cyber Systems and evaluate relevant NERC CIP requirements

Explanation

Correct Answer

D:

At the electric distribution substation, applicability and asset classification determine which NERC CIP safeguards must be assessed for the electric utility; that directly resolves the requirement that a North American electric utility needs to relate its cyber-system inventory and perimeter protections to the applicable NERC CIP obligations.

Incorrect Answers

A:

At the electric distribution substation, the expected mechanism is absent because a general security score cannot determine which electric-sector systems and obligations apply; it leaves unresolved the finding that a North American electric utility needs to relate its cyber-system inventory and perimeter protections to the applicable NERC CIP obligations.

B:

At the electric distribution substation, this mechanism serves the separate situation where the compliance workshop asks for a documented risk-based control approach to OT system security under ISA/IEC 62443, whereas the present finding is that a North American electric utility needs to relate its cyber-system inventory and perimeter protections to the applicable NERC CIP obligations; although ISA/IEC 62443 promotes risk-informed partitioning and explicitly governed communications across trust boundaries, the required capability remains missing.

C:

At the electric distribution substation, this mechanism serves the separate situation where the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture, whereas the present finding is that a North American electric utility needs to relate its cyber-system inventory and perimeter protections to the applicable NERC CIP obligations; although a Purdue mapping separates enterprise, site operations and process-control levels so boundary controls can be placed deliberately, the required capability remains missing.

Question 263

For the upcoming controlled rollout at the bulk-material handling facility, the work package includes: (1) a handler fires on unrelated business traffic because its log selection includes the wrong source and subtype; and (2) a FortiSIEM report is empty even though operators know incidents exist for the same week. Which two measures correctly map to the operational and security requirements?

  1. Narrow the selected log sources and filtering fields to the relevant OT events; then check the report's selected data source, time range and incident filters
  2. Narrow the selected log sources and filtering fields to the relevant OT events; then change the report export format without fixing the event filters
  3. Change notification priority while leaving the handler's log-field selection unchanged; then check the report's selected data source, time range and incident filters
  4. Change notification priority while leaving the handler's log-field selection unchanged; then change the report export format without fixing the event filters
  5. Use an appropriate correlation event handler with the required grouping and window; then check the report's selected data source, time range and incident filters

Explanation

Correct Answer

A:

The first control fits because the event handler's data selection and filters determine the events that qualify; the second fits because reporting queries depend on correctly scoped events and normalized incident data. Together they resolve the separate findings at the bulk-material handling facility: a handler fires on unrelated business traffic because its log selection includes the wrong source and subtype, and a FortiSIEM report is empty even though operators know incidents exist for the same week. This addresses a handler fires on unrelated business traffic because its log selection includes the wrong source and subtype without bypassing the separate requirement that a FortiSIEM report is empty even though operators know incidents exist for the same week.

Incorrect Answers

B:

The first action is suitable because the event handler's data selection and filters determine the events that qualify; the second is misdirected because export format does not change whether the query selects the underlying incident records. At the bulk-material handling facility, the remaining second gap is that a FortiSIEM report is empty even though operators know incidents exist for the same week, even though a handler fires on unrelated business traffic because its log selection includes the wrong source and subtype is covered.

C:

The second part is useful because reporting queries depend on correctly scoped events and normalized incident data; however, the first part fails because alert priority changes cannot correct a predicate that matches unrelated log sources. The first gap remains unresolved at the bulk-material handling facility: a handler fires on unrelated business traffic because its log selection includes the wrong source and subtype; the second measure helps with a FortiSIEM report is empty even though operators know incidents exist for the same week but cannot repair it.

D:

The first substitution fails because alert priority changes cannot correct a predicate that matches unrelated log sources; the second fails because export format does not change whether the query selects the underlying incident records. For this bulk-material handling facility, the first finding is that a handler fires on unrelated business traffic because its log selection includes the wrong source and subtype, while the other is that a FortiSIEM report is empty even though operators know incidents exist for the same week; neither is corrected by the chosen substitutions.

E:

The second action addresses a FortiSIEM report is empty even though operators know incidents exist for the same week because reporting queries depend on correctly scoped events and normalized incident data, but the separate first finding still concerns a handler fires on unrelated business traffic because its log selection includes the wrong source and subtype. The proposed first mechanism belongs to a different requirement: multiple OT indicators need to be combined before raising one higher-confidence event; correlation evaluates a relationship among observations rather than assuming each individual event proves an incident, but despite the valid second control for a FortiSIEM report is empty even though operators know incidents exist for the same week, it does not resolve the first finding at the bulk-material handling facility: a handler fires on unrelated business traffic because its log selection includes the wrong source and subtype.

Question 264

The hydroelectric generation site is preparing a controlled rollout. One outstanding requirement is that IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries. The proposed shortcut is to expose IEC 104 services to any routable corporate address. Which alternative should the architect approve instead?

  1. Identify DNP3 traffic using its industrial protocol context and configured communications pattern
  2. Match known S7 communication needs with narrow source and destination policy and suitable inspection
  3. Expose IEC 104 services to any routable corporate address
  4. Define strictly scoped IEC 104 conduit policies consistent with authorized SCADA peers

Explanation

Correct Answer

D:

The relevant technical distinction for the hydroelectric generation site is that telemetry protocol awareness and peer restrictions reduce exposure of the substation interface; that directly resolves the requirement that IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries.

Incorrect Answers

A:

At the hydroelectric generation site, this mechanism serves the separate situation where an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions, whereas the present finding is that IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries; although DNP3 supports telemetry and control exchanges that require different baselines from web browsing, the required capability remains missing.

B:

At the hydroelectric generation site, this mechanism serves the separate situation where a PLC maintenance path using Siemens S7 must be limited to the approved engineering station, whereas the present finding is that IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries; although vendor-specific controller traffic should be constrained to the approved engineering workflow rather than a sitewide pass, the required capability remains missing.

C:

The mismatch at the hydroelectric generation site is specific to the observed control requirement: broad routed availability violates the small set of approved SCADA relationships; it leaves unresolved the finding that IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries.

Question 265

At a glass manufacturing line, engineers must address both of these documented gaps: (1) a ring-topology automation network has stringent recovery-time requirements before a segmentation change; and (2) the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified. Which TWO independently necessary controls directly fulfill the two requirements? Choose TWO.

  1. Insert a general all-services allow rule above specific OT rules
  2. Validate the industrial redundancy mechanism and the firewall failure behavior together
  3. Apply a default-deny inter-zone policy and allow only approved OT flows
  4. Assume any second Ethernet cable guarantees hitless recovery

Explanation

Correct Answers

B:

The relevant technical distinction for the glass manufacturing line is that acceptable availability depends on convergence and failover characteristics of the whole industrial path; that directly resolves the requirement that a ring-topology automation network has stringent recovery-time requirements before a segmentation change; it is evaluated alongside the separate requirement that the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified.

C:

In this glass manufacturing line scenario, an explicit service allowlist makes unapproved paths fail closed at the routed boundary; that directly resolves the requirement that the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified; it is evaluated alongside the separate requirement that a ring-topology automation network has stringent recovery-time requirements before a segmentation change.

Incorrect Answers

A:

At the glass manufacturing line, this substitutes a measure addressing a different concern: broad high-priority permission bypasses the intended least-privilege inspection; it leaves unresolved the finding that the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified; the parallel design also has to address a ring-topology automation network has stringent recovery-time requirements before a segmentation change.

D:

The mismatch at the glass manufacturing line is specific to the observed control requirement: physical duplication alone does not configure ring recovery or state continuity; it leaves unresolved the finding that a ring-topology automation network has stringent recovery-time requirements before a segmentation change; the parallel design also has to address the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified.

Question 266

For the upcoming controlled rollout at the municipal water-treatment facility, the work package includes: (1) a device has an identified vulnerability but its vendor update cannot be applied until the next outage; and (2) EtherNet/IP controller exchanges are allowed but an uncontrolled engineering port still exposes programming capabilities. Which joint design is aligned with the exact detection and enforcement gaps?

  1. Apply appropriate virtual patching coverage to the matching device traffic; then distinguish necessary cyclic industrial communications from unnecessary management or engineering access
  2. Apply appropriate virtual patching coverage to the matching device traffic; then treat all EtherNet/IP-associated services as one unrestricted application
  3. Declare the endpoint permanently remediated without testing the mitigation; then distinguish necessary cyclic industrial communications from unnecessary management or engineering access
  4. Declare the endpoint permanently remediated without testing the mitigation; then treat all EtherNet/IP-associated services as one unrestricted application

Explanation

Correct Answer

A:

The first control fits because virtual patching can use vulnerability-linked network mitigations without changing the controller firmware immediately; the second fits because EtherNet/IP operational traffic and configuration reachability can require different security treatment. Together they resolve the separate findings at the municipal water-treatment facility: a device has an identified vulnerability but its vendor update cannot be applied until the next outage, and EtherNet/IP controller exchanges are allowed but an uncontrolled engineering port still exposes programming capabilities. This addresses a device has an identified vulnerability but its vendor update cannot be applied until the next outage without bypassing the separate requirement that EtherNet/IP controller exchanges are allowed but an uncontrolled engineering port still exposes programming capabilities.

Incorrect Answers

B:

The first action is suitable because virtual patching can use vulnerability-linked network mitigations without changing the controller firmware immediately; the second is misdirected because a family-level blanket permit loses the ability to narrow sensitive maintenance behavior. At the municipal water-treatment facility, the remaining second gap is that EtherNet/IP controller exchanges are allowed but an uncontrolled engineering port still exposes programming capabilities, even though a device has an identified vulnerability but its vendor update cannot be applied until the next outage is covered.

C:

The second part is useful because EtherNet/IP operational traffic and configuration reachability can require different security treatment; however, the first part fails because a network workaround does not replace the underlying vendor patch or validate the residual exposure. The first gap remains unresolved at the municipal water-treatment facility: a device has an identified vulnerability but its vendor update cannot be applied until the next outage; the second measure helps with EtherNet/IP controller exchanges are allowed but an uncontrolled engineering port still exposes programming capabilities but cannot repair it.

D:

The first substitution fails because a network workaround does not replace the underlying vendor patch or validate the residual exposure; the second fails because a family-level blanket permit loses the ability to narrow sensitive maintenance behavior. For this municipal water-treatment facility, the first finding is that a device has an identified vulnerability but its vendor update cannot be applied until the next outage, while the other is that EtherNet/IP controller exchanges are allowed but an uncontrolled engineering port still exposes programming capabilities; neither is corrected by the chosen substitutions.

Question 267

A post-installation check at the cement kiln control room finds two outstanding configuration gaps: (1) the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified; and (2) existing domain sign-in information must inform access decisions without repeatedly prompting authenticated workstation users. Which paired action most directly satisfies both findings without introducing an unrelated control change?

  1. Insert a general all-services allow rule above specific OT rules; then evaluate Fortinet single sign-on integration and user-to-IP mappings
  2. Apply a default-deny inter-zone policy and allow only approved OT flows; then evaluate Fortinet single sign-on integration and user-to-IP mappings
  3. Insert a general all-services allow rule above specific OT rules; then replace user association with a static source-IP allowlist
  4. Apply a default-deny inter-zone policy and allow only approved OT flows; then replace user association with a static source-IP allowlist

Explanation

Correct Answer

B:

The first control fits because an explicit service allowlist makes unapproved paths fail closed at the routed boundary; the second fits because FSSO can make identity associations available to firewall policy when the identity source and mapping are trusted. Together they resolve the separate findings at the cement kiln control room: the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified, and existing domain sign-in information must inform access decisions without repeatedly prompting authenticated workstation users. This addresses the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified without bypassing the separate requirement that existing domain sign-in information must inform access decisions without repeatedly prompting authenticated workstation users.

Incorrect Answers

A:

The second part is useful because FSSO can make identity associations available to firewall policy when the identity source and mapping are trusted; however, the first part fails because broad high-priority permission bypasses the intended least-privilege inspection. The first gap remains unresolved at the cement kiln control room: the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified; the second measure helps with existing domain sign-in information must inform access decisions without repeatedly prompting authenticated workstation users but cannot repair it.

C:

The first substitution fails because broad high-priority permission bypasses the intended least-privilege inspection; the second fails because a reusable workstation address does not reliably identify the person currently signed in. For this cement kiln control room, the first finding is that the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified, while the other is that existing domain sign-in information must inform access decisions without repeatedly prompting authenticated workstation users; neither is corrected by the chosen substitutions.

D:

The first action is suitable because an explicit service allowlist makes unapproved paths fail closed at the routed boundary; the second is misdirected because a reusable workstation address does not reliably identify the person currently signed in. At the cement kiln control room, the remaining second gap is that existing domain sign-in information must inform access decisions without repeatedly prompting authenticated workstation users, even though the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified is covered.

Question 268

A staged deployment for the port container terminal cannot proceed until both conditions are handled: (1) a plant wants to check whether an emergency data route bypasses its intended industrial DMZ; and (2) device classification based only on vendor OUI confuses similar products from the same manufacturer. What two-part implementation is the most precise response to the stated requirements?

  1. Verify the implemented path against the defined OT zones and boundary policy; then refine FortiNAC profiling rules with additional observed attributes and higher-specificity criteria
  2. Assume any route with low latency is authorized; then force every endpoint from one OUI into a single controller class
  3. Assume any route with low latency is authorized; then refine FortiNAC profiling rules with additional observed attributes and higher-specificity criteria
  4. Verify the implemented path against the defined OT zones and boundary policy; then force every endpoint from one OUI into a single controller class

Explanation

Correct Answer

A:

The first control fits because comparing actual network paths with approved conduits reveals ungoverned enterprise-to-control bypasses; the second fits because the MAC vendor prefix is only a partial clue and stronger profile criteria reduce false classifications. Together they resolve the separate findings at the port container terminal: a plant wants to check whether an emergency data route bypasses its intended industrial DMZ, and device classification based only on vendor OUI confuses similar products from the same manufacturer. This addresses a plant wants to check whether an emergency data route bypasses its intended industrial DMZ without bypassing the separate requirement that device classification based only on vendor OUI confuses similar products from the same manufacturer.

Incorrect Answers

B:

The first substitution fails because acceptable response time does not establish that a cross-zone path meets security requirements; the second fails because shared manufacturer identifiers cannot reliably distinguish different endpoint functions. For this port container terminal, the first finding is that a plant wants to check whether an emergency data route bypasses its intended industrial DMZ, while the other is that device classification based only on vendor OUI confuses similar products from the same manufacturer; neither is corrected by the chosen substitutions.

C:

The second part is useful because the MAC vendor prefix is only a partial clue and stronger profile criteria reduce false classifications; however, the first part fails because acceptable response time does not establish that a cross-zone path meets security requirements. The first gap remains unresolved at the port container terminal: a plant wants to check whether an emergency data route bypasses its intended industrial DMZ; the second measure helps with device classification based only on vendor OUI confuses similar products from the same manufacturer but cannot repair it.

D:

The first action is suitable because comparing actual network paths with approved conduits reveals ungoverned enterprise-to-control bypasses; the second is misdirected because shared manufacturer identifiers cannot reliably distinguish different endpoint functions. At the port container terminal, the remaining second gap is that device classification based only on vendor OUI confuses similar products from the same manufacturer, even though a plant wants to check whether an emergency data route bypasses its intended industrial DMZ is covered.

Question 269

A plant security engineer at the natural-gas compression station needs a focused remedy because a firewall pair protects an essential plant conduit and a single device failure must not become an extended outage. The proposed shortcut is to configure independent appliances with no coordinated failover plan. Which alternative should the architect approve instead?

  1. Apply a default-deny inter-zone policy and allow only approved OT flows
  2. Use separate FortiGate VDOMs with appropriate inter-VDOM boundaries
  3. Design and test appropriate FortiGate high availability for the conduit
  4. Configure independent appliances with no coordinated failover plan

Explanation

Correct Answer

C:

For the stated gap at the natural-gas compression station, an HA design can preserve a service boundary across appliance faults if session behavior and failover are validated; that directly resolves the requirement that a firewall pair protects an essential plant conduit and a single device failure must not become an extended outage.

Incorrect Answers

A:

At the natural-gas compression station, this mechanism serves the separate situation where the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified, whereas the present finding is that a firewall pair protects an essential plant conduit and a single device failure must not become an extended outage; although an explicit service allowlist makes unapproved paths fail closed at the routed boundary, the required capability remains missing.

B:

At the natural-gas compression station, this mechanism serves the separate situation where the security team must keep two production units' routing tables and firewall administration separate on shared hardware, whereas the present finding is that a firewall pair protects an essential plant conduit and a single device failure must not become an extended outage; although VDOM isolation separates routing and policy contexts rather than merely giving interfaces different labels, the required capability remains missing.

D:

At the natural-gas compression station, that alternative is insufficient because redundant boxes alone do not ensure traffic switches to the standby path correctly; it leaves unresolved the finding that a firewall pair protects an essential plant conduit and a single device failure must not become an extended outage.

Question 270

The district water pumping plant is preparing a controlled rollout. One outstanding requirement is that the security engineer must decide which severity levels are actively blocked and which are only logged. What is the most targeted response?

  1. Check valid update connectivity or the approved offline package update path
  2. Increase traffic logging while leaving virtual-patching severity actions unchanged
  3. Review device-level and signature-level exemption lists before assuming signature failure
  4. Define and test the severity and action choices within a virtual patching profile

Explanation

Correct Answer

D:

At the district water pumping plant, profile-level action and severity selections set which matched mitigations are enforced versus observed; that directly resolves the requirement that the security engineer must decide which severity levels are actively blocked and which are only logged.

Incorrect Answers

A:

At the district water pumping plant, this mechanism serves the separate situation where the team expects current device vulnerability mappings after new FortiGuard definitions are issued, whereas the present finding is that the security engineer must decide which severity levels are actively blocked and which are only logged; although local signature and vulnerability intelligence must be refreshed through an authorized update workflow, the required capability remains missing.

B:

At the district water pumping plant, the expected mechanism is absent because extra visibility does not configure which virtual-patching severities should block a session; it leaves unresolved the finding that the security engineer must decide which severity levels are actively blocked and which are only logged.

C:

At the district water pumping plant, this mechanism serves the separate situation where a virtual patching exemption has been configured for a known device and its expected mitigation is not applied, whereas the present finding is that the security engineer must decide which severity levels are actively blocked and which are only logged; although an exempted MAC or rule can intentionally skip otherwise applicable virtual patching checks, the required capability remains missing.

Fortinet NSE 6 - OT Security 7.6 Architect (NSE6_OTS_AR-7.6) Practice Tests