Fortinet NSE6_OTS_AR-7.6 (Fortinet NSE 6 - OT Security 7.6 Architect) Practice Test 29

Question 280

The controls engineer and SOC analyst for the battery manufacturing line must jointly address the following: (1) a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization; and (2) a plant wants to check whether an emergency data route bypasses its intended industrial DMZ. Which combination addresses the required mechanisms at their proper enforcement or observation points?

  1. Record sensors, actuators, PLCs and supervisory components by operational role; then assume any route with low latency is authorized
  2. Classify all equipment as interchangeable Ethernet endpoints; then verify the implemented path against the defined OT zones and boundary policy
  3. Classify all equipment as interchangeable Ethernet endpoints; then assume any route with low latency is authorized
  4. Record sensors, actuators, PLCs and supervisory components by operational role; then verify the implemented path against the defined OT zones and boundary policy

Explanation

Correct Answer

D:

The first control fits because recognizing field measurement, physical actuation, controller logic and supervisory functions is essential to impact analysis; the second fits because comparing actual network paths with approved conduits reveals ungoverned enterprise-to-control bypasses. Together they resolve the separate findings at the battery manufacturing line: a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization, and a plant wants to check whether an emergency data route bypasses its intended industrial DMZ. This addresses a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization without bypassing the separate requirement that a plant wants to check whether an emergency data route bypasses its intended industrial DMZ.

Incorrect Answers

A:

The first action is suitable because recognizing field measurement, physical actuation, controller logic and supervisory functions is essential to impact analysis; the second is misdirected because acceptable response time does not establish that a cross-zone path meets security requirements. At the battery manufacturing line, the remaining second gap is that a plant wants to check whether an emergency data route bypasses its intended industrial DMZ, even though a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization is covered.

B:

The second part is useful because comparing actual network paths with approved conduits reveals ungoverned enterprise-to-control bypasses; however, the first part fails because a generic network label obscures who senses, controls or merely displays industrial processes. The first gap remains unresolved at the battery manufacturing line: a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization; the second measure helps with a plant wants to check whether an emergency data route bypasses its intended industrial DMZ but cannot repair it.

C:

The first substitution fails because a generic network label obscures who senses, controls or merely displays industrial processes; the second fails because acceptable response time does not establish that a cross-zone path meets security requirements. For this battery manufacturing line, the first finding is that a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization, while the other is that a plant wants to check whether an emergency data route bypasses its intended industrial DMZ; neither is corrected by the chosen substitutions.

Question 281

The operations and security teams for the rail signaling depot agree on these acceptance criteria: (1) an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet; and (2) a contractor account has been removed from the identity provider but an old local allow rule still provides broad access. Which two measures correctly map to the operational and security requirements?

  1. Put a suitable intra-zone enforcement point on the actual device-to-device path; then leave a permanent all-contractor subnet allow rule as a fallback
  2. Restrict only the plant's outbound Internet URL categories; then align firewall authorizations with up-to-date user group membership and session handling
  3. Put a suitable intra-zone enforcement point on the actual device-to-device path; then align firewall authorizations with up-to-date user group membership and session handling
  4. Restrict only the plant's outbound Internet URL categories; then leave a permanent all-contractor subnet allow rule as a fallback
  5. Document MAC/VLAN boundaries separately from routed policy conduits; then align firewall authorizations with up-to-date user group membership and session handling

Explanation

Correct Answer

C:

The first control fits because microsegmentation requires the target communications to cross a control capable of applying per-flow rules; the second fits because revocation must be reflected in both identity state and effective policy for the access path. Together they resolve the separate findings at the rail signaling depot: an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet, and a contractor account has been removed from the identity provider but an old local allow rule still provides broad access. This addresses an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet without bypassing the separate requirement that a contractor account has been removed from the identity provider but an old local allow rule still provides broad access.

Incorrect Answers

A:

The first action is suitable because microsegmentation requires the target communications to cross a control capable of applying per-flow rules; the second is misdirected because an IP-only bypass defeats centralized deprovisioning and least privilege. At the rail signaling depot, the remaining second gap is that a contractor account has been removed from the identity provider but an old local allow rule still provides broad access, even though an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet is covered.

B:

The second part is useful because revocation must be reflected in both identity state and effective policy for the access path; however, the first part fails because external browsing filters do not govern local device-to-device traffic inside the control zone. The first gap remains unresolved at the rail signaling depot: an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet; the second measure helps with a contractor account has been removed from the identity provider but an old local allow rule still provides broad access but cannot repair it.

D:

The first substitution fails because external browsing filters do not govern local device-to-device traffic inside the control zone; the second fails because an IP-only bypass defeats centralized deprovisioning and least privilege. For this rail signaling depot, the first finding is that an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet, while the other is that a contractor account has been removed from the identity provider but an old local allow rule still provides broad access; neither is corrected by the chosen substitutions.

E:

The second action addresses a contractor account has been removed from the identity provider but an old local allow rule still provides broad access because revocation must be reflected in both identity state and effective policy for the access path, but the separate first finding still concerns an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet. The proposed first mechanism belongs to a different requirement: controls engineers need to identify which flows must remain routable while preserving the existing layer-two broadcast structure; switching domains and layer-three enforcement are different constructs that must both be represented in the design, but despite the valid second control for a contractor account has been removed from the identity provider but an old local allow rule still provides broad access, it does not resolve the first finding at the rail signaling depot: an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet.

Question 282

An audit at the semiconductor fabrication facility finds that the plant must preserve the identity and connection history of a registered technician workstation for access investigations. What is the most targeted response?

  1. Review the ranking and specificity of enabled device profiling rules
  2. Maintain the endpoint in FortiNAC Host View with appropriate user association
  3. Investigate the rogue-host record and allow the profiling workflow to classify it
  4. Replace the host record with a static switch-port label

Explanation

Correct Answer

B:

The relevant technical distinction for the semiconductor fabrication facility is that Host View preserves host and connection context needed for accountability and access workflows; that directly resolves the requirement that the plant must preserve the identity and connection history of a registered technician workstation for access investigations.

Incorrect Answers

A:

At the semiconductor fabrication facility, this mechanism serves the separate situation where a rogue device has an IP address and multiple profiling rules might match different attributes, whereas the present finding is that the plant must preserve the identity and connection history of a registered technician workstation for access investigations; although FortiNAC evaluates eligible rules by rank so precedence affects the first matching classification, the required capability remains missing.

C:

At the semiconductor fabrication facility, this mechanism serves the separate situation where FortiNAC sees an unknown MAC address connected to a switch but the host has not been registered, whereas the present finding is that the plant must preserve the identity and connection history of a registered technician workstation for access investigations; although an unrecognized MAC is initially tracked as a rogue and can be evaluated against profiling criteria once observations are available, the required capability remains missing.

D:

The mismatch at the semiconductor fabrication facility is specific to the observed control requirement: a port description does not retain host history or link the observed endpoint with an accountable user; it leaves unresolved the finding that the plant must preserve the identity and connection history of a registered technician workstation for access investigations.

Question 283

The technical reviewer for the regional pipeline control center must select controls for these two findings: (1) controls engineers need to identify which flows must remain routable while preserving the existing layer-two broadcast structure; and (2) a disabled endpoint must have substantially no operational-network access regardless of prior registration. Which two measures correctly map to the operational and security requirements?

  1. Define distinct VLANs for the engineering and control populations; then use the FortiNAC disabled or dead-end isolation enforcement state
  2. Document MAC/VLAN boundaries separately from routed policy conduits; then re-enable the device automatically whenever it reconnects
  3. Document MAC/VLAN boundaries separately from routed policy conduits; then use the FortiNAC disabled or dead-end isolation enforcement state
  4. Treat the existing VLAN tags as sufficient to authorize all routed services; then use the FortiNAC disabled or dead-end isolation enforcement state
  5. Treat the existing VLAN tags as sufficient to authorize all routed services; then re-enable the device automatically whenever it reconnects

Explanation

Correct Answer

C:

The first control fits because switching domains and layer-three enforcement are different constructs that must both be represented in the design; the second fits because a disabled host should be held in a restrictive network state instead of rejoining production. Together they resolve the separate findings at the regional pipeline control center: controls engineers need to identify which flows must remain routable while preserving the existing layer-two broadcast structure, and a disabled endpoint must have substantially no operational-network access regardless of prior registration. This addresses controls engineers need to identify which flows must remain routable while preserving the existing layer-two broadcast structure without bypassing the separate requirement that a disabled endpoint must have substantially no operational-network access regardless of prior registration.

Incorrect Answers

A:

The second action addresses a disabled endpoint must have substantially no operational-network access regardless of prior registration because a disabled host should be held in a restrictive network state instead of rejoining production, but the separate first finding still concerns controls engineers need to identify which flows must remain routable while preserving the existing layer-two broadcast structure. The proposed first mechanism belongs to a different requirement: traffic from an engineer workstation and a safety controller shares one untagged broadcast domain; VLAN separation limits layer-two broadcast reach and enables more explicit inter-VLAN policy boundaries, but despite the valid second control for a disabled endpoint must have substantially no operational-network access regardless of prior registration, it does not resolve the first finding at the regional pipeline control center: controls engineers need to identify which flows must remain routable while preserving the existing layer-two broadcast structure.

B:

The first action is suitable because switching domains and layer-three enforcement are different constructs that must both be represented in the design; the second is misdirected because reconnecting does not override the administrator's disabled state. At the regional pipeline control center, the remaining second gap is that a disabled endpoint must have substantially no operational-network access regardless of prior registration, even though controls engineers need to identify which flows must remain routable while preserving the existing layer-two broadcast structure is covered.

D:

The second part is useful because a disabled host should be held in a restrictive network state instead of rejoining production; however, the first part fails because tagging expresses layer-two membership but does not specify permitted layer-three connections. The first gap remains unresolved at the regional pipeline control center: controls engineers need to identify which flows must remain routable while preserving the existing layer-two broadcast structure; the second measure helps with a disabled endpoint must have substantially no operational-network access regardless of prior registration but cannot repair it.

E:

The first substitution fails because tagging expresses layer-two membership but does not specify permitted layer-three connections; the second fails because reconnecting does not override the administrator's disabled state. For this regional pipeline control center, the first finding is that controls engineers need to identify which flows must remain routable while preserving the existing layer-two broadcast structure, while the other is that a disabled endpoint must have substantially no operational-network access regardless of prior registration; neither is corrected by the chosen substitutions.

Question 284

An audit at the wind-farm collector substation finds that traffic from an engineer workstation and a safety controller shares one untagged broadcast domain. The proposed shortcut is to install a router ACL while retaining the original shared layer-two segment. Which alternative should the architect approve instead?

  1. Define distinct VLANs for the engineering and control populations
  2. Install a router ACL while retaining the original shared layer-two segment
  3. Put a suitable intra-zone enforcement point on the actual device-to-device path
  4. Audit allowed tagged VLANs and native-VLAN behavior on both trunk ends

Explanation

Correct Answer

A:

In this wind-farm collector substation scenario, VLAN separation limits layer-two broadcast reach and enables more explicit inter-VLAN policy boundaries; that directly resolves the requirement that traffic from an engineer workstation and a safety controller shares one untagged broadcast domain.

Incorrect Answers

B:

At the wind-farm collector substation, this substitutes a measure addressing a different concern: a routed ACL may filter subnet crossings but does not split a common layer-two broadcast domain; it leaves unresolved the finding that traffic from an engineer workstation and a safety controller shares one untagged broadcast domain.

C:

At the wind-farm collector substation, this mechanism serves the separate situation where an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet, whereas the present finding is that traffic from an engineer workstation and a safety controller shares one untagged broadcast domain; although microsegmentation requires the target communications to cross a control capable of applying per-flow rules, the required capability remains missing.

D:

At the wind-farm collector substation, this mechanism serves the separate situation where industrial trunk links have inconsistent VLAN tagging and an isolated OT segment leaks into an unintended access network, whereas the present finding is that traffic from an engineer workstation and a safety controller shares one untagged broadcast domain; although consistent trunk membership prevents a control VLAN from being carried where it is not approved, the required capability remains missing.

Question 285

The design authority for the battery manufacturing line reports this gap: inspection cannot identify a command in encrypted application traffic because only ciphertext crosses the firewall. The proposed shortcut is to increase the logging retention time while leaving the payload encrypted. Which alternative should the architect approve instead?

  1. Increase the logging retention time while leaving the payload encrypted
  2. Evaluate supported decryption or a suitable alternative inspection point within safety constraints
  3. Enable a suitable IPS security profile on the conduit firewall policy
  4. Verify the relevant FortiGuard OT Security Service license before relying on the package

Explanation

Correct Answer

B:

The relevant technical distinction for the battery manufacturing line is that a payload analyzer cannot interpret encrypted commands unless the necessary content becomes visible at a trusted point; that directly resolves the requirement that inspection cannot identify a command in encrypted application traffic because only ciphertext crosses the firewall.

Incorrect Answers

A:

The mismatch at the battery manufacturing line is specific to the observed control requirement: storing more ciphertext does not create visibility into its application-layer command; it leaves unresolved the finding that inspection cannot identify a command in encrypted application traffic because only ciphertext crosses the firewall.

C:

At the battery manufacturing line, this mechanism serves the separate situation where the plant wants OT signatures to inspect a controller conduit but the policy has no active IPS profile, whereas the present finding is that inspection cannot identify a command in encrypted application traffic because only ciphertext crosses the firewall; although the dedicated OT attack definitions are used by IPS inspection when the service is valid and policy is configured, the required capability remains missing.

D:

At the battery manufacturing line, this mechanism serves the separate situation where an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription, whereas the present finding is that inspection cannot identify a command in encrypted application traffic because only ciphertext crosses the firewall; although dedicated OT definitions depend on service entitlement as well as successful distribution and applied inspection, the required capability remains missing.

Question 286

A staged deployment for the industrial refrigeration installation cannot proceed until both conditions are handled: (1) planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network; and (2) a third-party OT monitoring sensor offers useful asset attributes but FortiNAC's native evidence is incomplete. Which joint design is aligned with the exact detection and enforcement gaps?

  1. Run unrestricted vulnerability scans on every field controller during production; then authorize unverified imported device labels as trusted production roles
  2. Identify time-critical controllers and field devices and prefer passive discovery initially; then plan a supported third-party OT discovery integration with verified field mapping
  3. Identify time-critical controllers and field devices and prefer passive discovery initially; then authorize unverified imported device labels as trusted production roles
  4. Run unrestricted vulnerability scans on every field controller during production; then plan a supported third-party OT discovery integration with verified field mapping

Explanation

Correct Answer

B:

The first control fits because controllers and field equipment can have strict latency and availability constraints that make intrusive discovery inappropriate; the second fits because external industrial visibility can enrich asset classification when integration and trust boundaries are validated. Together they resolve the separate findings at the industrial refrigeration installation: planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network, and a third-party OT monitoring sensor offers useful asset attributes but FortiNAC's native evidence is incomplete. This addresses planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network without bypassing the separate requirement that a third-party OT monitoring sensor offers useful asset attributes but FortiNAC's native evidence is incomplete.

Incorrect Answers

A:

The first substitution fails because indiscriminate active probing can disrupt legacy or timing-sensitive industrial endpoints; the second fails because asset metadata alone cannot prove the live endpoint is authorized to enter a production access role. For this industrial refrigeration installation, the first finding is that planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network, while the other is that a third-party OT monitoring sensor offers useful asset attributes but FortiNAC's native evidence is incomplete; neither is corrected by the chosen substitutions.

C:

The first action is suitable because controllers and field equipment can have strict latency and availability constraints that make intrusive discovery inappropriate; the second is misdirected because asset metadata alone cannot prove the live endpoint is authorized to enter a production access role. At the industrial refrigeration installation, the remaining second gap is that a third-party OT monitoring sensor offers useful asset attributes but FortiNAC's native evidence is incomplete, even though planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network is covered.

D:

The second part is useful because external industrial visibility can enrich asset classification when integration and trust boundaries are validated; however, the first part fails because indiscriminate active probing can disrupt legacy or timing-sensitive industrial endpoints. The first gap remains unresolved at the industrial refrigeration installation: planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network; the second measure helps with a third-party OT monitoring sensor offers useful asset attributes but FortiNAC's native evidence is incomplete but cannot repair it.

Question 287

At a wastewater pumping station, engineers must address both of these documented gaps: (1) an engineering workstation is allowed to read controller values but unauthorised program-changing operations must be controlled; and (2) IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries. Which TWO independently necessary controls directly fulfill the two requirements? Choose TWO.

  1. Define strictly scoped IEC 104 conduit policies consistent with authorized SCADA peers
  2. Allow every operation merely because it uses a familiar OT protocol
  3. Use protocol-aware industrial command controls where supported and validate safe operations
  4. Expose IEC 104 services to any routable corporate address

Explanation

Correct Answers

A:

At the wastewater pumping station, telemetry protocol awareness and peer restrictions reduce exposure of the substation interface; that directly resolves the requirement that IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries; it is evaluated alongside the separate requirement that an engineering workstation is allowed to read controller values but unauthorised program-changing operations must be controlled.

C:

For the stated gap at the wastewater pumping station, understanding allowed read versus write or configuration functions avoids treating all protocol payloads alike; that directly resolves the requirement that an engineering workstation is allowed to read controller values but unauthorised program-changing operations must be controlled; it is evaluated alongside the separate requirement that IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries.

Incorrect Answers

B:

At the wastewater pumping station, that alternative is insufficient because protocol family membership does not determine whether a particular controller command is safe; it leaves unresolved the finding that an engineering workstation is allowed to read controller values but unauthorised program-changing operations must be controlled; the parallel design also has to address IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries.

D:

At the wastewater pumping station, the expected mechanism is absent because broad routed availability violates the small set of approved SCADA relationships; it leaves unresolved the finding that IEC 60870-5-104 telemetry from a remote substation requires controlled inbound and outbound trust boundaries; the parallel design also has to address an engineering workstation is allowed to read controller values but unauthorised program-changing operations must be controlled.

Question 288

Before the district water pumping plant accepts a proposed OT security architecture, it must demonstrate: (1) planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network; and (2) the asset dashboard omits the OT vulnerability context needed for identifying devices with known exploited flaws. Which proposal would pass both acceptance tests with the fewest irrelevant changes?

  1. Identify time-critical controllers and field devices and prefer passive discovery initially; then confirm device identification and necessary security-profile processing for IoT/OT visibility
  2. Run unrestricted vulnerability scans on every field controller during production; then disable all UTM processing while expecting the same enrichment
  3. Run unrestricted vulnerability scans on every field controller during production; then confirm device identification and necessary security-profile processing for IoT/OT visibility
  4. Identify time-critical controllers and field devices and prefer passive discovery initially; then disable all UTM processing while expecting the same enrichment

Explanation

Correct Answer

A:

The first control fits because controllers and field equipment can have strict latency and availability constraints that make intrusive discovery inappropriate; the second fits because device identity processing and relevant inspected traffic supply asset attributes that enable enriched vulnerability views. Together they resolve the separate findings at the district water pumping plant: planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network, and the asset dashboard omits the OT vulnerability context needed for identifying devices with known exploited flaws. This addresses planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network without bypassing the separate requirement that the asset dashboard omits the OT vulnerability context needed for identifying devices with known exploited flaws.

Incorrect Answers

B:

The first substitution fails because indiscriminate active probing can disrupt legacy or timing-sensitive industrial endpoints; the second fails because disabling inspection can remove observations needed to associate assets with vulnerability information. For this district water pumping plant, the first finding is that planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network, while the other is that the asset dashboard omits the OT vulnerability context needed for identifying devices with known exploited flaws; neither is corrected by the chosen substitutions.

C:

The second part is useful because device identity processing and relevant inspected traffic supply asset attributes that enable enriched vulnerability views; however, the first part fails because indiscriminate active probing can disrupt legacy or timing-sensitive industrial endpoints. The first gap remains unresolved at the district water pumping plant: planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network; the second measure helps with the asset dashboard omits the OT vulnerability context needed for identifying devices with known exploited flaws but cannot repair it.

D:

The first action is suitable because controllers and field equipment can have strict latency and availability constraints that make intrusive discovery inappropriate; the second is misdirected because disabling inspection can remove observations needed to associate assets with vulnerability information. At the district water pumping plant, the remaining second gap is that the asset dashboard omits the OT vulnerability context needed for identifying devices with known exploited flaws, even though planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network is covered.

Question 289

For the upcoming controlled rollout at the wind-farm collector substation, the work package includes: (1) planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network; and (2) the OT team cannot tell which industrial asset provided the source IP of a detected threat. What two-part implementation is the most precise response to the stated requirements?

  1. Run unrestricted vulnerability scans on every field controller during production; then remove source identity fields from the SIEM ingest pipeline
  2. Run unrestricted vulnerability scans on every field controller during production; then associate firewall events with resolved device identity and asset attributes
  3. Identify time-critical controllers and field devices and prefer passive discovery initially; then associate firewall events with resolved device identity and asset attributes
  4. Identify time-critical controllers and field devices and prefer passive discovery initially; then remove source identity fields from the SIEM ingest pipeline

Explanation

Correct Answer

C:

The first control fits because controllers and field equipment can have strict latency and availability constraints that make intrusive discovery inappropriate; the second fits because enriched asset-to-IP associations make events actionable for specific controllers instead of only transient addresses. Together they resolve the separate findings at the wind-farm collector substation: planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network, and the OT team cannot tell which industrial asset provided the source IP of a detected threat. This addresses planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network without bypassing the separate requirement that the OT team cannot tell which industrial asset provided the source IP of a detected threat.

Incorrect Answers

A:

The first substitution fails because indiscriminate active probing can disrupt legacy or timing-sensitive industrial endpoints; the second fails because discarding device identity prevents analysts from relating alerts to the affected industrial asset. For this wind-farm collector substation, the first finding is that planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network, while the other is that the OT team cannot tell which industrial asset provided the source IP of a detected threat; neither is corrected by the chosen substitutions.

B:

The second part is useful because enriched asset-to-IP associations make events actionable for specific controllers instead of only transient addresses; however, the first part fails because indiscriminate active probing can disrupt legacy or timing-sensitive industrial endpoints. The first gap remains unresolved at the wind-farm collector substation: planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network; the second measure helps with the OT team cannot tell which industrial asset provided the source IP of a detected threat but cannot repair it.

D:

The first action is suitable because controllers and field equipment can have strict latency and availability constraints that make intrusive discovery inappropriate; the second is misdirected because discarding device identity prevents analysts from relating alerts to the affected industrial asset. At the wind-farm collector substation, the remaining second gap is that the OT team cannot tell which industrial asset provided the source IP of a detected threat, even though planners must identify the most safety-sensitive elements before authorizing active security probing of an OT network is covered.

Question 290

The controls engineer and SOC analyst for the district water pumping plant must jointly address the following: (1) a plant wants to check whether an emergency data route bypasses its intended industrial DMZ; and (2) a rogue device has an IP address and multiple profiling rules might match different attributes. Which plan provides the needed control for each finding rather than a superficial substitute?

  1. Assume any route with low latency is authorized; then review the ranking and specificity of enabled device profiling rules
  2. Verify the implemented path against the defined OT zones and boundary policy; then review the ranking and specificity of enabled device profiling rules
  3. Verify the implemented path against the defined OT zones and boundary policy; then assume rule names are evaluated in alphabetical order
  4. Assume any route with low latency is authorized; then assume rule names are evaluated in alphabetical order

Explanation

Correct Answer

B:

The first control fits because comparing actual network paths with approved conduits reveals ungoverned enterprise-to-control bypasses; the second fits because FortiNAC evaluates eligible rules by rank so precedence affects the first matching classification. Together they resolve the separate findings at the district water pumping plant: a plant wants to check whether an emergency data route bypasses its intended industrial DMZ, and a rogue device has an IP address and multiple profiling rules might match different attributes. This addresses a plant wants to check whether an emergency data route bypasses its intended industrial DMZ without bypassing the separate requirement that a rogue device has an IP address and multiple profiling rules might match different attributes.

Incorrect Answers

A:

The second part is useful because FortiNAC evaluates eligible rules by rank so precedence affects the first matching classification; however, the first part fails because acceptable response time does not establish that a cross-zone path meets security requirements. The first gap remains unresolved at the district water pumping plant: a plant wants to check whether an emergency data route bypasses its intended industrial DMZ; the second measure helps with a rogue device has an IP address and multiple profiling rules might match different attributes but cannot repair it.

C:

The first action is suitable because comparing actual network paths with approved conduits reveals ungoverned enterprise-to-control bypasses; the second is misdirected because rule descriptions do not supersede the configured profiling rule rank. At the district water pumping plant, the remaining second gap is that a rogue device has an IP address and multiple profiling rules might match different attributes, even though a plant wants to check whether an emergency data route bypasses its intended industrial DMZ is covered.

D:

The first substitution fails because acceptable response time does not establish that a cross-zone path meets security requirements; the second fails because rule descriptions do not supersede the configured profiling rule rank. For this district water pumping plant, the first finding is that a plant wants to check whether an emergency data route bypasses its intended industrial DMZ, while the other is that a rogue device has an IP address and multiple profiling rules might match different attributes; neither is corrected by the chosen substitutions.

Fortinet NSE 6 - OT Security 7.6 Architect (NSE6_OTS_AR-7.6) Practice Tests