Question 560
At a food-processing factory, engineers must address both of these documented gaps: (1) the security engineer must decide which severity levels are actively blocked and which are only logged; and (2) a suspected compromised maintenance laptop must be contained while continuing operation of fixed safety controllers. Which TWO independently necessary controls directly fulfill the two requirements? Choose TWO.
- Define and test the severity and action choices within a virtual patching profile
- Increase traffic logging while leaving virtual-patching severity actions unchanged
- Disconnect the complete PLC subnet in response to one laptop alert
- Target the affected noncritical endpoint through FortiNAC or policy-based access restriction
Explanation
Correct Answers
A:The relevant technical distinction for the food-processing factory is that profile-level action and severity selections set which matched mitigations are enforced versus observed; that directly resolves the requirement that the security engineer must decide which severity levels are actively blocked and which are only logged; it is evaluated alongside the separate requirement that a suspected compromised maintenance laptop must be contained while continuing operation of fixed safety controllers.
D:In this food-processing factory scenario, containment should act on the identified workstation rather than remove an entire safety-critical control cell; that directly resolves the requirement that a suspected compromised maintenance laptop must be contained while continuing operation of fixed safety controllers; it is evaluated alongside the separate requirement that the security engineer must decide which severity levels are actively blocked and which are only logged.
Incorrect Answers
B:The mismatch at the food-processing factory is specific to the observed control requirement: extra visibility does not configure which virtual-patching severities should block a session; it leaves unresolved the finding that the security engineer must decide which severity levels are actively blocked and which are only logged; the parallel design also has to address a suspected compromised maintenance laptop must be contained while continuing operation of fixed safety controllers.
C:At the food-processing factory, this substitutes a measure addressing a different concern: subnet-wide isolation sacrifices unrelated process availability and exceeds the identified blast radius; it leaves unresolved the finding that a suspected compromised maintenance laptop must be contained while continuing operation of fixed safety controllers; the parallel design also has to address the security engineer must decide which severity levels are actively blocked and which are only logged.
Question 561
At a petrochemical blending plant, engineers must address both of these documented gaps: (1) an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription; and (2) the FortiGate knows an asset's vulnerability but its flow bypasses the firewall policy bearing the virtual patching profile. Which TWO independently necessary controls directly fulfill the two requirements? Choose TWO.
- Put the profile on the real traffic path through a matching firewall policy
- Expand the dashboard widget while leaving the routing bypass
- Update the generic IPS definitions without checking the separate OT entitlement
- Verify the relevant FortiGuard OT Security Service license before relying on the package
- Apply the sensor to the actual matching firewall policy and confirm policy hits
Explanation
Correct Answers
A:The relevant technical distinction for the petrochemical blending plant is that a policy-attached virtual patch is not effective for traffic that does not cross that policy; that directly resolves the requirement that the FortiGate knows an asset's vulnerability but its flow bypasses the firewall policy bearing the virtual patching profile; it is evaluated alongside the separate requirement that an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription.
D:At the petrochemical blending plant, dedicated OT definitions depend on service entitlement as well as successful distribution and applied inspection; that directly resolves the requirement that an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription; it is evaluated alongside the separate requirement that the FortiGate knows an asset's vulnerability but its flow bypasses the firewall policy bearing the virtual patching profile.
Incorrect Answers
B:The mismatch at the petrochemical blending plant is specific to the observed control requirement: dashboard presentation cannot force bypassing sessions through a mitigation point; it leaves unresolved the finding that the FortiGate knows an asset's vulnerability but its flow bypasses the firewall policy bearing the virtual patching profile; the parallel design also has to address an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription.
C:At the petrochemical blending plant, the expected mechanism is absent because generic IPS updates cannot substitute for an unlicensed dedicated OT signature package; it leaves unresolved the finding that an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription; the parallel design also has to address the FortiGate knows an asset's vulnerability but its flow bypasses the firewall policy bearing the virtual patching profile.
E:At the petrochemical blending plant, this mechanism serves the separate situation where a policy has an OT application sensor configured but traffic is governed by a different matching firewall rule, whereas the present finding is that an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription; although security profiles act on traffic traversing the enabled policy, not merely on the profile object existing, the required capability remains missing.
Question 562
A security assessment of the cement kiln control room records two issues: (1) OT and IoT signatures are inadvertently excluded from the detection configuration on a FortiGate interface; and (2) an already registered device was classified incorrectly and rerunning rogue rules does not change it. What is the technically justified combination for the two separate observations?
- Review the interface signature-exclusion settings for OT and IoT discovery; then run rogue profiling repeatedly without changing registration state
- Increase general traffic logging while leaving OT signature categories excluded; then run rogue profiling repeatedly without changing registration state
- Increase general traffic logging while leaving OT signature categories excluded; then manually correct the registered host or reintroduce it into the appropriate classification workflow
- Review the interface signature-exclusion settings for OT and IoT discovery; then manually correct the registered host or reintroduce it into the appropriate classification workflow
Explanation
Correct Answer
D:The first control fits because excluded signature categories suppress matching for those device types and reduce available asset details; the second fits because profiling re-evaluation acts on remaining rogues rather than automatically rewriting every registered inventory object. Together they resolve the separate findings at the cement kiln control room: OT and IoT signatures are inadvertently excluded from the detection configuration on a FortiGate interface, and an already registered device was classified incorrectly and rerunning rogue rules does not change it. This addresses OT and IoT signatures are inadvertently excluded from the detection configuration on a FortiGate interface without bypassing the separate requirement that an already registered device was classified incorrectly and rerunning rogue rules does not change it.
Incorrect Answers
A:The first action is suitable because excluded signature categories suppress matching for those device types and reduce available asset details; the second is misdirected because a registered endpoint is outside the ordinary rogue-only re-evaluation scope. At the cement kiln control room, the remaining second gap is that an already registered device was classified incorrectly and rerunning rogue rules does not change it, even though OT and IoT signatures are inadvertently excluded from the detection configuration on a FortiGate interface is covered.
B:The first substitution fails because more log records cannot re-enable detection categories explicitly excluded at the interface; the second fails because a registered endpoint is outside the ordinary rogue-only re-evaluation scope. For this cement kiln control room, the first finding is that OT and IoT signatures are inadvertently excluded from the detection configuration on a FortiGate interface, while the other is that an already registered device was classified incorrectly and rerunning rogue rules does not change it; neither is corrected by the chosen substitutions.
C:The second part is useful because profiling re-evaluation acts on remaining rogues rather than automatically rewriting every registered inventory object; however, the first part fails because more log records cannot re-enable detection categories explicitly excluded at the interface. The first gap remains unresolved at the cement kiln control room: OT and IoT signatures are inadvertently excluded from the detection configuration on a FortiGate interface; the second measure helps with an already registered device was classified incorrectly and rerunning rogue rules does not change it but cannot repair it.
Question 563
An overnight review of the rail signaling depot reveals these unrelated but concurrent findings: (1) investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile; and (2) an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions. Which proposal fixes both issues while leaving unrelated OT workloads alone?
- Examine both firewall traffic action logs and security-profile event details; then apply a generic HTTP-only parsing assumption to DNP3 events
- Examine only source and destination addresses without inspecting security-event action fields; then apply a generic HTTP-only parsing assumption to DNP3 events
- Deploy network-based IPS or virtual patch protection at the applicable segment boundary; then identify DNP3 traffic using its industrial protocol context and configured communications pattern
- Examine both firewall traffic action logs and security-profile event details; then identify DNP3 traffic using its industrial protocol context and configured communications pattern
- Examine only source and destination addresses without inspecting security-event action fields; then identify DNP3 traffic using its industrial protocol context and configured communications pattern
Explanation
Correct Answer
D:The first control fits because session policy decisions and IPS or application detections are different observations requiring correlation; the second fits because DNP3 supports telemetry and control exchanges that require different baselines from web browsing. Together they resolve the separate findings at the rail signaling depot: investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile, and an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions. This addresses investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile without bypassing the separate requirement that an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions.
Incorrect Answers
A:The first action is suitable because session policy decisions and IPS or application detections are different observations requiring correlation; the second is misdirected because a web request parser does not describe DNP3 operational functions or expected field-device messages. At the rail signaling depot, the remaining second gap is that an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions, even though investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile is covered.
B:The first substitution fails because endpoint addressing cannot reveal whether the blocking decision came from policy matching or IPS; the second fails because a web request parser does not describe DNP3 operational functions or expected field-device messages. For this rail signaling depot, the first finding is that investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile, while the other is that an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions; neither is corrected by the chosen substitutions.
C:The second action addresses an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions because DNP3 supports telemetry and control exchanges that require different baselines from web browsing, but the separate first finding still concerns investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile. The proposed first mechanism belongs to a different requirement: a plant wants to contain an exploit on a legacy PLC without installing an agent on the controller; inline network inspection can mitigate selected exploit traffic while leaving the unmodifiable endpoint software untouched, but despite the valid second control for an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions, it does not resolve the first finding at the rail signaling depot: investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile.
E:The second part is useful because DNP3 supports telemetry and control exchanges that require different baselines from web browsing; however, the first part fails because endpoint addressing cannot reveal whether the blocking decision came from policy matching or IPS. The first gap remains unresolved at the rail signaling depot: investigators must identify whether industrial operations were blocked by policy or by a threat-detection profile; the second measure helps with an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions but cannot repair it.
Question 564
An industrial network audit at the pharmaceutical production floor establishes two requirements: (1) the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture; and (2) a site wants independent policy administration and traffic isolation for separate industrial tenants on the same FortiGate. Which proposal would pass both acceptance tests with the fewest irrelevant changes?
- Treat every PLC and cloud application as the same Purdue level; then put different sites into one unrestricted default policy
- Treat every PLC and cloud application as the same Purdue level; then evaluate virtual domains with separate routing and policy contexts
- Map the plant's functions to the Purdue model before defining security boundaries; then put different sites into one unrestricted default policy
- Map the plant's functions to the Purdue model before defining security boundaries; then evaluate virtual domains with separate routing and policy contexts
- Group systems into security zones and document controlled conduits between them; then evaluate virtual domains with separate routing and policy contexts
Explanation
Correct Answer
D:The first control fits because a Purdue mapping separates enterprise, site operations and process-control levels so boundary controls can be placed deliberately; the second fits because VDOMs provide logical separation of firewall configuration and forwarding contexts on a shared FortiGate. Together they resolve the separate findings at the pharmaceutical production floor: the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture, and a site wants independent policy administration and traffic isolation for separate industrial tenants on the same FortiGate. This addresses the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture without bypassing the separate requirement that a site wants independent policy administration and traffic isolation for separate industrial tenants on the same FortiGate.
Incorrect Answers
A:The first substitution fails because collapsing levels hides important differences in function and exposure between control and enterprise systems; the second fails because a shared broad rule does not create independent administration or routing contexts. For this pharmaceutical production floor, the first finding is that the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture, while the other is that a site wants independent policy administration and traffic isolation for separate industrial tenants on the same FortiGate; neither is corrected by the chosen substitutions.
B:The second part is useful because VDOMs provide logical separation of firewall configuration and forwarding contexts on a shared FortiGate; however, the first part fails because collapsing levels hides important differences in function and exposure between control and enterprise systems. The first gap remains unresolved at the pharmaceutical production floor: the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture; the second measure helps with a site wants independent policy administration and traffic isolation for separate industrial tenants on the same FortiGate but cannot repair it.
C:The first action is suitable because a Purdue mapping separates enterprise, site operations and process-control levels so boundary controls can be placed deliberately; the second is misdirected because a shared broad rule does not create independent administration or routing contexts. At the pharmaceutical production floor, the remaining second gap is that a site wants independent policy administration and traffic isolation for separate industrial tenants on the same FortiGate, even though the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture is covered.
E:The second action addresses a site wants independent policy administration and traffic isolation for separate industrial tenants on the same FortiGate because VDOMs provide logical separation of firewall configuration and forwarding contexts on a shared FortiGate, but the separate first finding still concerns the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture. The proposed first mechanism belongs to a different requirement: assets with unlike safety and trust requirements are treated as a single flat security group despite an ISA/IEC 62443 zone-and-conduit design requirement; comparable security requirements belong in zones and the inter-zone paths need separately governed conduits, but despite the valid second control for a site wants independent policy administration and traffic isolation for separate industrial tenants on the same FortiGate, it does not resolve the first finding at the pharmaceutical production floor: the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture.
Question 565
A post-installation check at the rail signaling depot finds two outstanding configuration gaps: (1) a ring-topology automation network has stringent recovery-time requirements before a segmentation change; and (2) an unregistered maintenance laptop should be unable to join the production VLAN until approved. Which two measures correctly map to the operational and security requirements?
- Assume any second Ethernet cable guarantees hitless recovery; then configure FortiNAC forced registration with an appropriate registration or isolation VLAN
- Validate the industrial redundancy mechanism and the firewall failure behavior together; then place all newly seen endpoints immediately in the production VLAN
- Validate the industrial redundancy mechanism and the firewall failure behavior together; then configure FortiNAC forced registration with an appropriate registration or isolation VLAN
- Assume any second Ethernet cable guarantees hitless recovery; then place all newly seen endpoints immediately in the production VLAN
Explanation
Correct Answer
C:The first control fits because acceptable availability depends on convergence and failover characteristics of the whole industrial path; the second fits because unknown endpoints can be put into a restricted VLAN pending their registration and authorization. Together they resolve the separate findings at the rail signaling depot: a ring-topology automation network has stringent recovery-time requirements before a segmentation change, and an unregistered maintenance laptop should be unable to join the production VLAN until approved. This addresses a ring-topology automation network has stringent recovery-time requirements before a segmentation change without bypassing the separate requirement that an unregistered maintenance laptop should be unable to join the production VLAN until approved.
Incorrect Answers
A:The second part is useful because unknown endpoints can be put into a restricted VLAN pending their registration and authorization; however, the first part fails because physical duplication alone does not configure ring recovery or state continuity. The first gap remains unresolved at the rail signaling depot: a ring-topology automation network has stringent recovery-time requirements before a segmentation change; the second measure helps with an unregistered maintenance laptop should be unable to join the production VLAN until approved but cannot repair it.
B:The first action is suitable because acceptable availability depends on convergence and failover characteristics of the whole industrial path; the second is misdirected because open admission undermines the stated unknown-device quarantine policy. At the rail signaling depot, the remaining second gap is that an unregistered maintenance laptop should be unable to join the production VLAN until approved, even though a ring-topology automation network has stringent recovery-time requirements before a segmentation change is covered.
D:The first substitution fails because physical duplication alone does not configure ring recovery or state continuity; the second fails because open admission undermines the stated unknown-device quarantine policy. For this rail signaling depot, the first finding is that a ring-topology automation network has stringent recovery-time requirements before a segmentation change, while the other is that an unregistered maintenance laptop should be unable to join the production VLAN until approved; neither is corrected by the chosen substitutions.
Question 566
During troubleshooting of the district heating plant, the operator confirms that the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture. The proposed shortcut is to treat every PLC and cloud application as the same Purdue level. Which alternative should the architect approve instead?
- Group systems into security zones and document controlled conduits between them
- Treat every PLC and cloud application as the same Purdue level
- Map the plant's functions to the Purdue model before defining security boundaries
- Identify applicable BES Cyber Systems and evaluate relevant NERC CIP requirements
Explanation
Correct Answer
C:At the district heating plant, a Purdue mapping separates enterprise, site operations and process-control levels so boundary controls can be placed deliberately; that directly resolves the requirement that the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture.
Incorrect Answers
A:At the district heating plant, this mechanism serves the separate situation where assets with unlike safety and trust requirements are treated as a single flat security group despite an ISA/IEC 62443 zone-and-conduit design requirement, whereas the present finding is that the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture; although comparable security requirements belong in zones and the inter-zone paths need separately governed conduits, the required capability remains missing.
B:At the district heating plant, the expected mechanism is absent because collapsing levels hides important differences in function and exposure between control and enterprise systems; it leaves unresolved the finding that the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture.
D:At the district heating plant, this mechanism serves the separate situation where a North American electric utility needs to relate its cyber-system inventory and perimeter protections to the applicable NERC CIP obligations, whereas the present finding is that the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture; although applicability and asset classification determine which NERC CIP safeguards must be assessed for the electric utility, the required capability remains missing.
Question 567
A staged deployment for the regional pipeline control center cannot proceed until both conditions are handled: (1) an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription; and (2) the facility is air-gapped and cannot reach FortiGuard update servers directly. Which combination addresses the required mechanisms at their proper enforcement or observation points?
- Update the generic IPS definitions without checking the separate OT entitlement; then open unrestricted Internet access from all controllers for signature downloads
- Verify the relevant FortiGuard OT Security Service license before relying on the package; then use supported manual licensing and security package transfer procedures for the offline FortiGate
- Verify the relevant FortiGuard OT Security Service license before relying on the package; then open unrestricted Internet access from all controllers for signature downloads
- Update the generic IPS definitions without checking the separate OT entitlement; then use supported manual licensing and security package transfer procedures for the offline FortiGate
- Configure a suitable FortiGate application control sensor on the observed policy; then use supported manual licensing and security package transfer procedures for the offline FortiGate
Explanation
Correct Answer
B:The first control fits because dedicated OT definitions depend on service entitlement as well as successful distribution and applied inspection; the second fits because an air-gap deployment needs a controlled update transfer rather than assuming live FortiGuard queries. Together they resolve the separate findings at the regional pipeline control center: an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription, and the facility is air-gapped and cannot reach FortiGuard update servers directly. This addresses an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription without bypassing the separate requirement that the facility is air-gapped and cannot reach FortiGuard update servers directly.
Incorrect Answers
A:The first substitution fails because generic IPS updates cannot substitute for an unlicensed dedicated OT signature package; the second fails because exposing process devices violates the air-gap requirement and is not required for controlled package updates. For this regional pipeline control center, the first finding is that an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription, while the other is that the facility is air-gapped and cannot reach FortiGuard update servers directly; neither is corrected by the chosen substitutions.
C:The first action is suitable because dedicated OT definitions depend on service entitlement as well as successful distribution and applied inspection; the second is misdirected because exposing process devices violates the air-gap requirement and is not required for controlled package updates. At the regional pipeline control center, the remaining second gap is that the facility is air-gapped and cannot reach FortiGuard update servers directly, even though an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription is covered.
D:The second part is useful because an air-gap deployment needs a controlled update transfer rather than assuming live FortiGuard queries; however, the first part fails because generic IPS updates cannot substitute for an unlicensed dedicated OT signature package. The first gap remains unresolved at the regional pipeline control center: an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription; the second measure helps with the facility is air-gapped and cannot reach FortiGuard update servers directly but cannot repair it.
E:The second action addresses the facility is air-gapped and cannot reach FortiGuard update servers directly because an air-gap deployment needs a controlled update transfer rather than assuming live FortiGuard queries, but the separate first finding still concerns an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription. The proposed first mechanism belongs to a different requirement: security must recognize industrial application traffic even when it uses nonstandard transport ports; application identification uses protocol decoders and signatures rather than trusting port numbers alone, but despite the valid second control for the facility is air-gapped and cannot reach FortiGuard update servers directly, it does not resolve the first finding at the regional pipeline control center: an OT signature package is missing despite WAN connectivity and no valid dedicated OT service subscription.
Question 568
During a maintenance-window design exercise for the port container terminal, the team notes: (1) the plant wants OT signatures to inspect a controller conduit but the policy has no active IPS profile; and (2) a virtual patching exemption has been configured for a known device and its expected mitigation is not applied. What two-part implementation is the most precise response to the stated requirements?
- Enable only traffic logging while leaving IPS disabled; then review device-level and signature-level exemption lists before assuming signature failure
- Enable only traffic logging while leaving IPS disabled; then increase firewall logging without inspecting virtual-patching exemptions
- Enable a suitable IPS security profile on the conduit firewall policy; then increase firewall logging without inspecting virtual-patching exemptions
- Enable a suitable IPS security profile on the conduit firewall policy; then review device-level and signature-level exemption lists before assuming signature failure
Explanation
Correct Answer
D:The first control fits because the dedicated OT attack definitions are used by IPS inspection when the service is valid and policy is configured; the second fits because an exempted MAC or rule can intentionally skip otherwise applicable virtual patching checks. Together they resolve the separate findings at the port container terminal: the plant wants OT signatures to inspect a controller conduit but the policy has no active IPS profile, and a virtual patching exemption has been configured for a known device and its expected mitigation is not applied. This addresses the plant wants OT signatures to inspect a controller conduit but the policy has no active IPS profile without bypassing the separate requirement that a virtual patching exemption has been configured for a known device and its expected mitigation is not applied.
Incorrect Answers
A:The second part is useful because an exempted MAC or rule can intentionally skip otherwise applicable virtual patching checks; however, the first part fails because recording session metadata does not cause threat signatures to be evaluated. The first gap remains unresolved at the port container terminal: the plant wants OT signatures to inspect a controller conduit but the policy has no active IPS profile; the second measure helps with a virtual patching exemption has been configured for a known device and its expected mitigation is not applied but cannot repair it.
B:The first substitution fails because recording session metadata does not cause threat signatures to be evaluated; the second fails because more event records cannot override an exemption that skips protection for a device or rule. For this port container terminal, the first finding is that the plant wants OT signatures to inspect a controller conduit but the policy has no active IPS profile, while the other is that a virtual patching exemption has been configured for a known device and its expected mitigation is not applied; neither is corrected by the chosen substitutions.
C:The first action is suitable because the dedicated OT attack definitions are used by IPS inspection when the service is valid and policy is configured; the second is misdirected because more event records cannot override an exemption that skips protection for a device or rule. At the port container terminal, the remaining second gap is that a virtual patching exemption has been configured for a known device and its expected mitigation is not applied, even though the plant wants OT signatures to inspect a controller conduit but the policy has no active IPS profile is covered.
Question 569
The design authority for the glass manufacturing line reports this gap: the production VLAN should change according to the registered host's assigned industrial role. The proposed shortcut is to assign every registered host to the same unrestricted VLAN. Which alternative should the architect approve instead?
- Assign every registered host to the same unrestricted VLAN
- Use FortiNAC forced authentication on the relevant ports
- Apply FortiNAC role-based network access or matching network access policies
- Configure and map the restriction VLAN on the controlled switch before enforcing port changes
Explanation
Correct Answer
C:The relevant technical distinction for the glass manufacturing line is that the device or host role can drive the resulting VLAN instead of a single shared access state; that directly resolves the requirement that the production VLAN should change according to the registered host's assigned industrial role.
Incorrect Answers
A:The mismatch at the glass manufacturing line is specific to the observed control requirement: indiscriminate placement ignores differences between contractor, HMI and controller privileges; it leaves unresolved the finding that the production VLAN should change according to the registered host's assigned industrial role.
B:At the glass manufacturing line, this mechanism serves the separate situation where users on registered workstations need to authenticate before the access port returns to a production VLAN, whereas the present finding is that the production VLAN should change according to the registered host's assigned industrial role; although the isolated state can persist until a verified user authenticates to release the port, the required capability remains missing.
D:At the glass manufacturing line, this mechanism serves the separate situation where FortiNAC has identified a rogue device but the managed switch is not configured for the relevant isolation VLAN, whereas the present finding is that the production VLAN should change according to the registered host's assigned industrial role; although access enforcement depends on the switching infrastructure actually supporting the intended restricted VLAN, the required capability remains missing.
Question 570
The operations and security teams for the large-scale irrigation installation agree on these acceptance criteria: (1) an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet; and (2) the production VLAN should change according to the registered host's assigned industrial role. Which proposal would pass both acceptance tests with the fewest irrelevant changes?
- Restrict only the plant's outbound Internet URL categories; then assign every registered host to the same unrestricted VLAN
- Put a suitable intra-zone enforcement point on the actual device-to-device path; then apply FortiNAC role-based network access or matching network access policies
- Restrict only the plant's outbound Internet URL categories; then apply FortiNAC role-based network access or matching network access policies
- Put a suitable intra-zone enforcement point on the actual device-to-device path; then assign every registered host to the same unrestricted VLAN
Explanation
Correct Answer
B:The first control fits because microsegmentation requires the target communications to cross a control capable of applying per-flow rules; the second fits because the device or host role can drive the resulting VLAN instead of a single shared access state. Together they resolve the separate findings at the large-scale irrigation installation: an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet, and the production VLAN should change according to the registered host's assigned industrial role. This addresses an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet without bypassing the separate requirement that the production VLAN should change according to the registered host's assigned industrial role.
Incorrect Answers
A:The first substitution fails because external browsing filters do not govern local device-to-device traffic inside the control zone; the second fails because indiscriminate placement ignores differences between contractor, HMI and controller privileges. For this large-scale irrigation installation, the first finding is that an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet, while the other is that the production VLAN should change according to the registered host's assigned industrial role; neither is corrected by the chosen substitutions.
C:The second part is useful because the device or host role can drive the resulting VLAN instead of a single shared access state; however, the first part fails because external browsing filters do not govern local device-to-device traffic inside the control zone. The first gap remains unresolved at the large-scale irrigation installation: an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet; the second measure helps with the production VLAN should change according to the registered host's assigned industrial role but cannot repair it.
D:The first action is suitable because microsegmentation requires the target communications to cross a control capable of applying per-flow rules; the second is misdirected because indiscriminate placement ignores differences between contractor, HMI and controller privileges. At the large-scale irrigation installation, the remaining second gap is that the production VLAN should change according to the registered host's assigned industrial role, even though an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet is covered.