Fortinet NSE6_OTS_AR-7.6 (Fortinet NSE 6 - OT Security 7.6 Architect) Practice Test 86

Question 850

At a district heating plant, engineers must address both of these documented gaps: (1) the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified; and (2) a contractor account has been removed from the identity provider but an old local allow rule still provides broad access. Which TWO independently necessary controls directly fulfill the two requirements? Choose TWO.

  1. Insert a general all-services allow rule above specific OT rules
  2. Apply a default-deny inter-zone policy and allow only approved OT flows
  3. Align firewall authorizations with up-to-date user group membership and session handling
  4. Leave a permanent all-contractor subnet allow rule as a fallback
  5. Use separate FortiGate VDOMs with appropriate inter-VDOM boundaries

Explanation

Correct Answers

B:

In this district heating plant scenario, an explicit service allowlist makes unapproved paths fail closed at the routed boundary; that directly resolves the requirement that the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified; it is evaluated alongside the separate requirement that a contractor account has been removed from the identity provider but an old local allow rule still provides broad access.

C:

For the stated gap at the district heating plant, revocation must be reflected in both identity state and effective policy for the access path; that directly resolves the requirement that a contractor account has been removed from the identity provider but an old local allow rule still provides broad access; it is evaluated alongside the separate requirement that the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified.

Incorrect Answers

A:

At the district heating plant, this substitutes a measure addressing a different concern: broad high-priority permission bypasses the intended least-privilege inspection; it leaves unresolved the finding that the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified; the parallel design also has to address a contractor account has been removed from the identity provider but an old local allow rule still provides broad access.

D:

At the district heating plant, that alternative is insufficient because an IP-only bypass defeats centralized deprovisioning and least privilege; it leaves unresolved the finding that a contractor account has been removed from the identity provider but an old local allow rule still provides broad access; the parallel design also has to address the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified.

E:

At the district heating plant, this mechanism serves the separate situation where the security team must keep two production units' routing tables and firewall administration separate on shared hardware, whereas the present finding is that the firewall can route between controller and supervisory VLANs but traffic must be denied unless explicitly justified; although VDOM isolation separates routing and policy contexts rather than merely giving interfaces different labels, the required capability remains missing.

Question 851

At a hydroelectric generation site, engineers must address both of these documented gaps: (1) an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet; and (2) a compromised historian should not be able to initiate sessions to peer PLCs inside the same operational area. Which TWO independently necessary controls directly fulfill the two requirements? Choose TWO.

  1. Restrict only the plant's outbound Internet URL categories
  2. Inspect only traffic leaving the company for the Internet
  3. Put a suitable intra-zone enforcement point on the actual device-to-device path
  4. Introduce internal segmentation rules on actual historian-to-PLC forwarding paths

Explanation

Correct Answers

C:

The relevant technical distinction for the hydroelectric generation site is that microsegmentation requires the target communications to cross a control capable of applying per-flow rules; that directly resolves the requirement that an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet; it is evaluated alongside the separate requirement that a compromised historian should not be able to initiate sessions to peer PLCs inside the same operational area.

D:

In this hydroelectric generation site scenario, restricting east-west flows contains lateral movement that perimeter-only inspection would not see; that directly resolves the requirement that a compromised historian should not be able to initiate sessions to peer PLCs inside the same operational area; it is evaluated alongside the separate requirement that an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet.

Incorrect Answers

A:

The mismatch at the hydroelectric generation site is specific to the observed control requirement: external browsing filters do not govern local device-to-device traffic inside the control zone; it leaves unresolved the finding that an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet; the parallel design also has to address a compromised historian should not be able to initiate sessions to peer PLCs inside the same operational area.

B:

At the hydroelectric generation site, this substitutes a measure addressing a different concern: external egress policy misses peer-to-peer communications within the industrial environment; it leaves unresolved the finding that a compromised historian should not be able to initiate sessions to peer PLCs inside the same operational area; the parallel design also has to address an industrial device must stay in one fixed subnet and security must distinguish east-west flows on that subnet.

Question 852

The operations and security teams for the petrochemical blending plant agree on these acceptance criteria: (1) enterprise workstations can reach process controllers directly without traversing an approved industrial DMZ; and (2) a contractor account has been removed from the identity provider but an old local allow rule still provides broad access. What is the technically justified combination for the two separate observations?

  1. Add a broad allow-any rule from the enterprise network to PLCs; then leave a permanent all-contractor subnet allow rule as a fallback
  2. Route enterprise-to-OT administration through a segmented industrial DMZ; then leave a permanent all-contractor subnet allow rule as a fallback
  3. Use a controlled remote-access termination and a monitored jump host into permitted OT destinations; then align firewall authorizations with up-to-date user group membership and session handling
  4. Add a broad allow-any rule from the enterprise network to PLCs; then align firewall authorizations with up-to-date user group membership and session handling
  5. Route enterprise-to-OT administration through a segmented industrial DMZ; then align firewall authorizations with up-to-date user group membership and session handling

Explanation

Correct Answer

E:

The first control fits because a controlled intermediary zone limits direct trust between enterprise assets and process-control equipment; the second fits because revocation must be reflected in both identity state and effective policy for the access path. Together they resolve the separate findings at the petrochemical blending plant: enterprise workstations can reach process controllers directly without traversing an approved industrial DMZ, and a contractor account has been removed from the identity provider but an old local allow rule still provides broad access. This addresses enterprise workstations can reach process controllers directly without traversing an approved industrial DMZ without bypassing the separate requirement that a contractor account has been removed from the identity provider but an old local allow rule still provides broad access.

Incorrect Answers

A:

The first substitution fails because unconditional access defeats the protective purpose of the intermediate trust boundary; the second fails because an IP-only bypass defeats centralized deprovisioning and least privilege. For this petrochemical blending plant, the first finding is that enterprise workstations can reach process controllers directly without traversing an approved industrial DMZ, while the other is that a contractor account has been removed from the identity provider but an old local allow rule still provides broad access; neither is corrected by the chosen substitutions.

B:

The first action is suitable because a controlled intermediary zone limits direct trust between enterprise assets and process-control equipment; the second is misdirected because an IP-only bypass defeats centralized deprovisioning and least privilege. At the petrochemical blending plant, the remaining second gap is that a contractor account has been removed from the identity provider but an old local allow rule still provides broad access, even though enterprise workstations can reach process controllers directly without traversing an approved industrial DMZ is covered.

C:

The second action addresses a contractor account has been removed from the identity provider but an old local allow rule still provides broad access because revocation must be reflected in both identity state and effective policy for the access path, but the separate first finding still concerns enterprise workstations can reach process controllers directly without traversing an approved industrial DMZ. The proposed first mechanism belongs to a different requirement: a contractor requires short-lived access to OT but must not receive direct reachability from unmanaged external devices; brokered privileged access reduces direct exposure and supports session accountability, but despite the valid second control for a contractor account has been removed from the identity provider but an old local allow rule still provides broad access, it does not resolve the first finding at the petrochemical blending plant: enterprise workstations can reach process controllers directly without traversing an approved industrial DMZ.

D:

The second part is useful because revocation must be reflected in both identity state and effective policy for the access path; however, the first part fails because unconditional access defeats the protective purpose of the intermediate trust boundary. The first gap remains unresolved at the petrochemical blending plant: enterprise workstations can reach process controllers directly without traversing an approved industrial DMZ; the second measure helps with a contractor account has been removed from the identity provider but an old local allow rule still provides broad access but cannot repair it.

Question 853

The asset owner of the automated packaging warehouse wants to correct both of these deficiencies: (1) a compromised historian should not be able to initiate sessions to peer PLCs inside the same operational area; and (2) a disabled endpoint must have substantially no operational-network access regardless of prior registration. Which paired configuration should be included in the approved OT security change?

  1. Introduce internal segmentation rules on actual historian-to-PLC forwarding paths; then use the FortiNAC disabled or dead-end isolation enforcement state
  2. Introduce internal segmentation rules on actual historian-to-PLC forwarding paths; then re-enable the device automatically whenever it reconnects
  3. Inspect only traffic leaving the company for the Internet; then use the FortiNAC disabled or dead-end isolation enforcement state
  4. Inspect only traffic leaving the company for the Internet; then re-enable the device automatically whenever it reconnects

Explanation

Correct Answer

A:

The first control fits because restricting east-west flows contains lateral movement that perimeter-only inspection would not see; the second fits because a disabled host should be held in a restrictive network state instead of rejoining production. Together they resolve the separate findings at the automated packaging warehouse: a compromised historian should not be able to initiate sessions to peer PLCs inside the same operational area, and a disabled endpoint must have substantially no operational-network access regardless of prior registration. This addresses a compromised historian should not be able to initiate sessions to peer PLCs inside the same operational area without bypassing the separate requirement that a disabled endpoint must have substantially no operational-network access regardless of prior registration.

Incorrect Answers

B:

The first action is suitable because restricting east-west flows contains lateral movement that perimeter-only inspection would not see; the second is misdirected because reconnecting does not override the administrator's disabled state. At the automated packaging warehouse, the remaining second gap is that a disabled endpoint must have substantially no operational-network access regardless of prior registration, even though a compromised historian should not be able to initiate sessions to peer PLCs inside the same operational area is covered.

C:

The second part is useful because a disabled host should be held in a restrictive network state instead of rejoining production; however, the first part fails because external egress policy misses peer-to-peer communications within the industrial environment. The first gap remains unresolved at the automated packaging warehouse: a compromised historian should not be able to initiate sessions to peer PLCs inside the same operational area; the second measure helps with a disabled endpoint must have substantially no operational-network access regardless of prior registration but cannot repair it.

D:

The first substitution fails because external egress policy misses peer-to-peer communications within the industrial environment; the second fails because reconnecting does not override the administrator's disabled state. For this automated packaging warehouse, the first finding is that a compromised historian should not be able to initiate sessions to peer PLCs inside the same operational area, while the other is that a disabled endpoint must have substantially no operational-network access regardless of prior registration; neither is corrected by the chosen substitutions.

Question 854

The design authority for the automated packaging warehouse reports this gap: an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions. The proposed shortcut is to apply a generic HTTP-only parsing assumption to DNP3 events. Which alternative should the architect approve instead?

  1. Restrict OPC UA communications to approved clients and endpoints with appropriate protocol awareness
  2. Identify DNP3 traffic using its industrial protocol context and configured communications pattern
  3. Distinguish necessary cyclic industrial communications from unnecessary management or engineering access
  4. Apply a generic HTTP-only parsing assumption to DNP3 events

Explanation

Correct Answer

B:

The relevant technical distinction for the automated packaging warehouse is that DNP3 supports telemetry and control exchanges that require different baselines from web browsing; that directly resolves the requirement that an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions.

Incorrect Answers

A:

At the automated packaging warehouse, this mechanism serves the separate situation where an OPC UA telemetry server must serve selected clients but no other production hosts, whereas the present finding is that an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions; although restricting clients and service endpoints preserves authorized data exchange without treating the server as public infrastructure, the required capability remains missing.

C:

At the automated packaging warehouse, this mechanism serves the separate situation where EtherNet/IP controller exchanges are allowed but an uncontrolled engineering port still exposes programming capabilities, whereas the present finding is that an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions; although EtherNet/IP operational traffic and configuration reachability can require different security treatment, the required capability remains missing.

D:

The mismatch at the automated packaging warehouse is specific to the observed control requirement: a web request parser does not describe DNP3 operational functions or expected field-device messages; it leaves unresolved the finding that an event-monitoring design confuses DNP3 event communication with ordinary operator web sessions.

Question 855

A plant security engineer at the municipal water-treatment facility needs a focused remedy because the SOC receives too many low-confidence industrial IPS matches on a fragile production segment. The proposed shortcut is to disable all industrial IPS inspection permanently. Which alternative should the architect approve instead?

  1. Disable all industrial IPS inspection permanently
  2. Apply the sensor to the actual matching firewall policy and confirm policy hits
  3. Correlate application-control identification with IPS threat events
  4. Tune relevant signatures using evidence and staged monitoring before changing actions

Explanation

Correct Answer

D:

For the stated gap at the municipal water-treatment facility, narrowly targeted tuning can lower false positives without disabling unrelated protective coverage; that directly resolves the requirement that the SOC receives too many low-confidence industrial IPS matches on a fragile production segment.

Incorrect Answers

A:

At the municipal water-treatment facility, that alternative is insufficient because global disablement discards protection against other exploit classes along with the noisy match; it leaves unresolved the finding that the SOC receives too many low-confidence industrial IPS matches on a fragile production segment.

B:

At the municipal water-treatment facility, this mechanism serves the separate situation where a policy has an OT application sensor configured but traffic is governed by a different matching firewall rule, whereas the present finding is that the SOC receives too many low-confidence industrial IPS matches on a fragile production segment; although security profiles act on traffic traversing the enabled policy, not merely on the profile object existing, the required capability remains missing.

C:

At the municipal water-treatment facility, this mechanism serves the separate situation where the security team needs to distinguish the protocol family in OT traffic from whether a known exploit signature was triggered, whereas the present finding is that the SOC receives too many low-confidence industrial IPS matches on a fragile production segment; although application detection describes the traffic type while IPS alerts indicate a matching malicious pattern, the required capability remains missing.

Question 856

At a battery manufacturing line, engineers must address both of these documented gaps: (1) assets with unlike safety and trust requirements are treated as a single flat security group despite an ISA/IEC 62443 zone-and-conduit design requirement; and (2) operators need a record of a discovered switch-connected industrial device and whether it is currently reachable. Which TWO independently necessary controls directly fulfill the two requirements? Choose TWO.

  1. Map the plant's functions to the Purdue model before defining security boundaries
  2. Maintain only a list of IP addresses seen in historical firewall sessions
  3. Use FortiNAC inventory representation with connection-status monitoring
  4. Group systems into security zones and document controlled conduits between them
  5. Document switch-port asset labels without defining inter-zone policies

Explanation

Correct Answers

C:

The relevant technical distinction for the battery manufacturing line is that device inventory is suitable for managed asset presence and polling rather than only user-associated host history; that directly resolves the requirement that operators need a record of a discovered switch-connected industrial device and whether it is currently reachable; it is evaluated alongside the separate requirement that assets with unlike safety and trust requirements are treated as a single flat security group despite an ISA/IEC 62443 zone-and-conduit design requirement.

D:

At the battery manufacturing line, comparable security requirements belong in zones and the inter-zone paths need separately governed conduits; that directly resolves the requirement that assets with unlike safety and trust requirements are treated as a single flat security group despite an ISA/IEC 62443 zone-and-conduit design requirement; it is evaluated alongside the separate requirement that operators need a record of a discovered switch-connected industrial device and whether it is currently reachable.

Incorrect Answers

A:

At the battery manufacturing line, this mechanism serves the separate situation where the team cannot distinguish enterprise operations, the industrial DMZ, site operations and direct control layers in its reference architecture, whereas the present finding is that assets with unlike safety and trust requirements are treated as a single flat security group despite an ISA/IEC 62443 zone-and-conduit design requirement; although a Purdue mapping separates enterprise, site operations and process-control levels so boundary controls can be placed deliberately, the required capability remains missing.

B:

The mismatch at the battery manufacturing line is specific to the observed control requirement: a past traffic list does not maintain current managed-device connection state or reliable endpoint identity; it leaves unresolved the finding that operators need a record of a discovered switch-connected industrial device and whether it is currently reachable; the parallel design also has to address assets with unlike safety and trust requirements are treated as a single flat security group despite an ISA/IEC 62443 zone-and-conduit design requirement.

E:

At the battery manufacturing line, the expected mechanism is absent because switch-port documentation alone cannot establish zone trust or govern the path between different risk groups; it leaves unresolved the finding that assets with unlike safety and trust requirements are treated as a single flat security group despite an ISA/IEC 62443 zone-and-conduit design requirement; the parallel design also has to address operators need a record of a discovered switch-connected industrial device and whether it is currently reachable.

Question 857

An audit at the port container terminal finds that users on registered workstations need to authenticate before the access port returns to a production VLAN. What is the most targeted response?

  1. Use FortiNAC forced authentication on the relevant ports
  2. Use the FortiNAC disabled or dead-end isolation enforcement state
  3. Apply FortiNAC role-based network access or matching network access policies
  4. Substitute MAC registration as proof of the current human user

Explanation

Correct Answer

A:

The relevant technical distinction for the port container terminal is that the isolated state can persist until a verified user authenticates to release the port; that directly resolves the requirement that users on registered workstations need to authenticate before the access port returns to a production VLAN.

Incorrect Answers

B:

At the port container terminal, this mechanism serves the separate situation where a disabled endpoint must have substantially no operational-network access regardless of prior registration, whereas the present finding is that users on registered workstations need to authenticate before the access port returns to a production VLAN; although a disabled host should be held in a restrictive network state instead of rejoining production, the required capability remains missing.

C:

At the port container terminal, this mechanism serves the separate situation where the production VLAN should change according to the registered host's assigned industrial role, whereas the present finding is that users on registered workstations need to authenticate before the access port returns to a production VLAN; although the device or host role can drive the resulting VLAN instead of a single shared access state, the required capability remains missing.

D:

The mismatch at the port container terminal is specific to the observed control requirement: a registered device does not establish which individual is logged on; it leaves unresolved the finding that users on registered workstations need to authenticate before the access port returns to a production VLAN.

Question 858

An industrial network audit at the bulk-material handling facility establishes two requirements: (1) a basic handler exists but the incident queue remains empty after the intended event fires; and (2) a rule tests event sequences but the analyst cannot identify the actual controller that triggered an incident. Which paired configuration should be included in the approved OT security change?

  1. Increase the handler severity while leaving automatic incident creation disabled; then map meaningful triggered attributes into the incident details and review parsed device fields
  2. Increase the handler severity while leaving automatic incident creation disabled; then discard host identifiers after correlation to reduce table width
  3. Enable automatic incident creation in the relevant FortiAnalyzer event handler; then map meaningful triggered attributes into the incident details and review parsed device fields
  4. Enable automatic incident creation in the relevant FortiAnalyzer event handler; then discard host identifiers after correlation to reduce table width

Explanation

Correct Answer

C:

The first control fits because FortiAnalyzer can turn qualifying handler events into incidents when the create-incident setting is enabled; the second fits because the triggered context should retain the affected industrial entity to support triage and follow-up. Together they resolve the separate findings at the bulk-material handling facility: a basic handler exists but the incident queue remains empty after the intended event fires, and a rule tests event sequences but the analyst cannot identify the actual controller that triggered an incident. This addresses a basic handler exists but the incident queue remains empty after the intended event fires without bypassing the separate requirement that a rule tests event sequences but the analyst cannot identify the actual controller that triggered an incident.

Incorrect Answers

A:

The second part is useful because the triggered context should retain the affected industrial entity to support triage and follow-up; however, the first part fails because raising the event severity does not activate the distinct incident-creation switch. The first gap remains unresolved at the bulk-material handling facility: a basic handler exists but the incident queue remains empty after the intended event fires; the second measure helps with a rule tests event sequences but the analyst cannot identify the actual controller that triggered an incident but cannot repair it.

B:

The first substitution fails because raising the event severity does not activate the distinct incident-creation switch; the second fails because losing identifying fields makes the resulting incident harder to investigate and contain. For this bulk-material handling facility, the first finding is that a basic handler exists but the incident queue remains empty after the intended event fires, while the other is that a rule tests event sequences but the analyst cannot identify the actual controller that triggered an incident; neither is corrected by the chosen substitutions.

D:

The first action is suitable because FortiAnalyzer can turn qualifying handler events into incidents when the create-incident setting is enabled; the second is misdirected because losing identifying fields makes the resulting incident harder to investigate and contain. At the bulk-material handling facility, the remaining second gap is that a rule tests event sequences but the analyst cannot identify the actual controller that triggered an incident, even though a basic handler exists but the incident queue remains empty after the intended event fires is covered.

Question 859

A staged deployment for the hydroelectric generation site cannot proceed until both conditions are handled: (1) a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization; and (2) an already registered device was classified incorrectly and rerunning rogue rules does not change it. What two-part implementation is the most precise response to the stated requirements?

  1. Classify all equipment as interchangeable Ethernet endpoints; then manually correct the registered host or reintroduce it into the appropriate classification workflow
  2. Record sensors, actuators, PLCs and supervisory components by operational role; then manually correct the registered host or reintroduce it into the appropriate classification workflow
  3. Record sensors, actuators, PLCs and supervisory components by operational role; then run rogue profiling repeatedly without changing registration state
  4. Classify all equipment as interchangeable Ethernet endpoints; then run rogue profiling repeatedly without changing registration state

Explanation

Correct Answer

B:

The first control fits because recognizing field measurement, physical actuation, controller logic and supervisory functions is essential to impact analysis; the second fits because profiling re-evaluation acts on remaining rogues rather than automatically rewriting every registered inventory object. Together they resolve the separate findings at the hydroelectric generation site: a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization, and an already registered device was classified incorrectly and rerunning rogue rules does not change it. This addresses a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization without bypassing the separate requirement that an already registered device was classified incorrectly and rerunning rogue rules does not change it.

Incorrect Answers

A:

The second part is useful because profiling re-evaluation acts on remaining rogues rather than automatically rewriting every registered inventory object; however, the first part fails because a generic network label obscures who senses, controls or merely displays industrial processes. The first gap remains unresolved at the hydroelectric generation site: a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization; the second measure helps with an already registered device was classified incorrectly and rerunning rogue rules does not change it but cannot repair it.

C:

The first action is suitable because recognizing field measurement, physical actuation, controller logic and supervisory functions is essential to impact analysis; the second is misdirected because a registered endpoint is outside the ordinary rogue-only re-evaluation scope. At the hydroelectric generation site, the remaining second gap is that an already registered device was classified incorrectly and rerunning rogue rules does not change it, even though a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization is covered.

D:

The first substitution fails because a generic network label obscures who senses, controls or merely displays industrial processes; the second fails because a registered endpoint is outside the ordinary rogue-only re-evaluation scope. For this hydroelectric generation site, the first finding is that a new inventory fails to distinguish field sensing equipment from devices executing logic and supervisory visualization, while the other is that an already registered device was classified incorrectly and rerunning rogue rules does not change it; neither is corrected by the chosen substitutions.

Question 860

A security assessment of the natural-gas compression station records two issues: (1) sensors at a process-control layer must be visible to the SOC without exposing those sensors directly to the enterprise LAN; and (2) the administrator must verify whether the dedicated FortiGuard OT signature service is entitled before expecting OT-specific signatures. Which two measures correctly map to the operational and security requirements?

  1. Collect telemetry through approved segmented collectors and controlled boundary paths; then assume a default route alone proves OT signature licensing
  2. Collect telemetry through approved segmented collectors and controlled boundary paths; then check the Operational Technology Security Service entitlement under FortiGuard subscriptions
  3. Permit unrestricted enterprise access directly to the controller subnet; then check the Operational Technology Security Service entitlement under FortiGuard subscriptions
  4. Permit unrestricted enterprise access directly to the controller subnet; then assume a default route alone proves OT signature licensing

Explanation

Correct Answer

B:

The first control fits because controlled information flows preserve OT segmentation while supplying analysis outside sensitive control segments; the second fits because license entitlement governs access to the dedicated OT security signature updates. Together they resolve the separate findings at the natural-gas compression station: sensors at a process-control layer must be visible to the SOC without exposing those sensors directly to the enterprise LAN, and the administrator must verify whether the dedicated FortiGuard OT signature service is entitled before expecting OT-specific signatures. This addresses sensors at a process-control layer must be visible to the SOC without exposing those sensors directly to the enterprise LAN without bypassing the separate requirement that the administrator must verify whether the dedicated FortiGuard OT signature service is entitled before expecting OT-specific signatures.

Incorrect Answers

A:

The first action is suitable because controlled information flows preserve OT segmentation while supplying analysis outside sensitive control segments; the second is misdirected because Internet reachability by itself does not activate a subscription that has not been licensed. At the natural-gas compression station, the remaining second gap is that the administrator must verify whether the dedicated FortiGuard OT signature service is entitled before expecting OT-specific signatures, even though sensors at a process-control layer must be visible to the SOC without exposing those sensors directly to the enterprise LAN is covered.

C:

The second part is useful because license entitlement governs access to the dedicated OT security signature updates; however, the first part fails because broad inbound reachability enlarges the exposure of assets intended to remain isolated. The first gap remains unresolved at the natural-gas compression station: sensors at a process-control layer must be visible to the SOC without exposing those sensors directly to the enterprise LAN; the second measure helps with the administrator must verify whether the dedicated FortiGuard OT signature service is entitled before expecting OT-specific signatures but cannot repair it.

D:

The first substitution fails because broad inbound reachability enlarges the exposure of assets intended to remain isolated; the second fails because Internet reachability by itself does not activate a subscription that has not been licensed. For this natural-gas compression station, the first finding is that sensors at a process-control layer must be visible to the SOC without exposing those sensors directly to the enterprise LAN, while the other is that the administrator must verify whether the dedicated FortiGuard OT signature service is entitled before expecting OT-specific signatures; neither is corrected by the chosen substitutions.

Fortinet NSE 6 - OT Security 7.6 Architect (NSE6_OTS_AR-7.6) Practice Tests