Question 170
A FortiSwitch engineer in the airport office is documenting successful operation of “Configure VRRP on routed interfaces.” Which measurement or inspection confirms it?
- Check VRRP master state and failover behavior for the virtual gateway
- Review LACP operational members and negotiated actor/partner status
- Inspect the SVI addressing and corresponding connected route in the routing table
- Check delivered watts, endpoint PoE class and remaining switch power budget
- Capture the broadcast on another member of the same VLAN but not on a different VLAN
Explanation
Correct Answer
A:For the stated requirement, VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet. Directly measuring that result demonstrates whether the step to provide a shared default-gateway address resilient to one router failing succeeded on an endpoint-facing FortiSwitch port.
Incorrect Answers
B:This check is suited to “Use LACP to build a trunk” when trying to combine physical Ethernet links into one negotiated logical channel, not to verify “Configure VRRP on routed interfaces” at the airport office. Checking “Configure VRRP on routed interfaces” at the airport office requires evidence of its own mechanism: VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet; that is not the outcome measured by “Use LACP to build a trunk”.
C:The proposed check concerns “Create an SVI with a gateway IP” rather than “Configure VRRP on routed interfaces”: a switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled. For “Configure VRRP on routed interfaces” on an endpoint-facing FortiSwitch port, a better test would be to check VRRP master state and failover behavior for the virtual gateway, which targets provide a shared default-gateway address resilient to one router failing rather than the alternative diagnostic “Create an SVI with a gateway IP”.
D:This check is suited to “Allocate PoE power to a camera port” when trying to power a supported endpoint over its Ethernet connection without a local adapter, not to verify “Configure VRRP on routed interfaces” at the airport office. Checking “Configure VRRP on routed interfaces” at the airport office requires evidence of its own mechanism: VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet; that is not the outcome measured by “Allocate PoE power to a camera port”.
E:The proposed check concerns “Replicate Ethernet broadcast within a broadcast domain” rather than “Configure VRRP on routed interfaces”: broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port. For “Configure VRRP on routed interfaces” on an endpoint-facing FortiSwitch port, a better test would be to check VRRP master state and failover behavior for the virtual gateway, which targets provide a shared default-gateway address resilient to one router failing rather than the alternative diagnostic “Replicate Ethernet broadcast within a broadcast domain”.
Question 171
A production incident in the conference venue reveals the need to combine physical Ethernet links into one negotiated logical channel. Which targeted FortiSwitch setting or method should the team use?
- Establish BGP peering for prefix exchange
- Use LACP to build a trunk
- Replicate Ethernet broadcast within a broadcast domain
- Flood unknown unicast only within its VLAN
Explanation
Correct Answer
B:The deciding detail is that LACP identifies compatible members and provides link-level redundancy for a logical aggregate. This distinction is material to the conference venue, where the stated goal is to combine physical Ethernet links into one negotiated logical channel.
Incorrect Answers
A:Compared with the requested “Use LACP to build a trunk” at the conference venue, this would exchange policy-controlled routing information with an external routing peer instead: BGP maintains sessions with configured neighbors and selects routes using its path attributes. At the conference venue, the operational proof would instead be to review LACP operational members and negotiated actor/partner status, whereas “Establish BGP peering for prefix exchange” is validated by a different test: inspect BGP neighbor session state and the prefix received from the remote autonomous system.
C:Compared with the requested “Use LACP to build a trunk” at the conference venue, this would reach all eligible peers for a local Layer 2 discovery request instead: broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port. At the conference venue, the operational proof would instead be to review LACP operational members and negotiated actor/partner status, whereas “Replicate Ethernet broadcast within a broadcast domain” is validated by a different test: capture the broadcast on another member of the same VLAN but not on a different VLAN.
D:For the conference venue, “Flood unknown unicast only within its VLAN” is a different type of control from “Use LACP to build a trunk”: unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain. Unlike the requested feature, that setting addresses the need to deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary, not the objective to combine physical Ethernet links into one negotiated logical channel.
Question 172
A switch change for the campus consists of this step: use LACP to build a trunk. Which behavior reflects the purpose of that change?
- VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet
- LACP identifies compatible members and provides link-level redundancy for a logical aggregate
- The switch PoE subsystem supplies negotiated electrical power within the model's available budget
- A switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled
Explanation
Correct Answer
B:The relevant mechanism is: the configured operation is meant to combine physical Ethernet links into one negotiated logical channel. The most relevant validation is to review LACP operational members and negotiated actor/partner status for the equipment at the campus.
Incorrect Answers
A:That behavior applies when engineers “Configure VRRP on routed interfaces”; the different operation “Use LACP to build a trunk” is intended to combine physical Ethernet links into one negotiated logical channel. That different feature is verified by check VRRP master state and failover behavior for the virtual gateway; for “Use LACP to build a trunk” on a newly commissioned floor switch, the relevant evidence is to review LACP operational members and negotiated actor/partner status.
C:That behavior applies when engineers “Allocate PoE power to a camera port”; the different operation “Use LACP to build a trunk” is intended to combine physical Ethernet links into one negotiated logical channel. That different feature is verified by check delivered watts, endpoint PoE class and remaining switch power budget; for “Use LACP to build a trunk” on a newly commissioned floor switch, the relevant evidence is to review LACP operational members and negotiated actor/partner status.
D:This outcome would be relevant to “Create an SVI with a gateway IP” at the campus, not the task “Use LACP to build a trunk”; the other task is to route traffic from one VLAN subnet toward other routed networks. The action “Use LACP to build a trunk” targets a different result: LACP identifies compatible members and provides link-level redundancy for a logical aggregate; the proposed alternative would instead be checked by inspect the SVI addressing and corresponding connected route in the routing table.
Question 173
The change plan at the remote depot contains “Use LACP to build a trunk.” Which THREE statements correctly characterize its objective, effect and validation? (Choose THREE.)
- A static route adds an operator-defined forwarding path subject to route selection and reachability
- LACP identifies compatible members and provides link-level redundancy for a logical aggregate
- It is intended to combine physical Ethernet links into one negotiated logical channel
- Review LACP operational members and negotiated actor/partner status
- The switch learns IGMP group membership and forwards multicast to interested ports
Explanation
Correct Answers
B:The mechanism of “Use LACP to build a trunk” produces this result on a local switch administering branch clients, matching the goal to combine physical Ethernet links into one negotiated logical channel.
C:The action “Use LACP to build a trunk” was selected to meet that precise requirement at the remote depot; the desired mechanism is that LACP identifies compatible members and provides link-level redundancy for a logical aggregate.
D:This is an operational test of “Use LACP to build a trunk” at the remote depot, whose expected behavior is that LACP identifies compatible members and provides link-level redundancy for a logical aggregate.
Incorrect Answers
A:This result belongs to “Install a static route,” which addresses the need to give the switch a manually controlled next hop for a known remote prefix instead of “Use LACP to build a trunk” at the remote depot. The actual expected effect of “Use LACP to build a trunk” is LACP identifies compatible members and provides link-level redundancy for a logical aggregate; that is separate from the task handled by “Install a static route”.
E:This result belongs to “Enable IGMP snooping for multicast VLANs,” which addresses the need to avoid flooding subscribed multicast traffic to every access port instead of “Use LACP to build a trunk” at the remote depot. The actual expected effect of “Use LACP to build a trunk” is LACP identifies compatible members and provides link-level redundancy for a logical aggregate; that is separate from the task handled by “Enable IGMP snooping for multicast VLANs”.
Question 174
A switch rollout in the branch office will be approved only if it can power a supported endpoint over its Ethernet connection without a local adapter. Which administrative action meets this acceptance criterion?
- Learn source MAC addresses per VLAN
- Allocate PoE power to a camera port
- Enable OSPF adjacency on routed interfaces
- Establish BGP peering for prefix exchange
- Flood unknown unicast only within its VLAN
Explanation
Correct Answer
B:The critical distinction is that the switch PoE subsystem supplies negotiated electrical power within the model's available budget. The operator can test this claim by the specific check: check delivered watts, endpoint PoE class and remaining switch power budget.
Incorrect Answers
A:Compared with the requested “Allocate PoE power to a camera port” at the branch office, this would forward future unicast traffic efficiently to a known endpoint instead: the switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN. At the branch office, the operational proof would instead be to check delivered watts, endpoint PoE class and remaining switch power budget, whereas “Learn source MAC addresses per VLAN” is validated by a different test: inspect the learned MAC table for VLAN and ingress-port association.
C:For the branch office, “Enable OSPF adjacency on routed interfaces” is a different type of control from “Allocate PoE power to a camera port”: OSPF forms neighbor relationships and advertises reachable prefixes within configured areas. Unlike the requested feature, that setting addresses the need to exchange dynamic route information with neighboring Layer 3 devices, not the objective to power a supported endpoint over its Ethernet connection without a local adapter.
D:Compared with the requested “Allocate PoE power to a camera port” at the branch office, this would exchange policy-controlled routing information with an external routing peer instead: BGP maintains sessions with configured neighbors and selects routes using its path attributes. At the branch office, the operational proof would instead be to check delivered watts, endpoint PoE class and remaining switch power budget, whereas “Establish BGP peering for prefix exchange” is validated by a different test: inspect BGP neighbor session state and the prefix received from the remote autonomous system.
E:Compared with the requested “Allocate PoE power to a camera port” at the branch office, this would deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary instead: unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain. At the branch office, the operational proof would instead be to check delivered watts, endpoint PoE class and remaining switch power budget, whereas “Flood unknown unicast only within its VLAN” is validated by a different test: clear a learned destination and observe initial flooding only to permitted VLAN members.
Question 175
The operator has decided to allocate PoE power to a camera port on a production FortiSwitch fabric at the factory. Which operational behavior is the most reasonable expectation of that specific feature?
- The switch PoE subsystem supplies negotiated electrical power within the model's available budget
- A switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled
- VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet
- Broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port
Explanation
Correct Answer
A:That setting is appropriate here because the configured operation is meant to power a supported endpoint over its Ethernet connection without a local adapter. The most relevant validation is to check delivered watts, endpoint PoE class and remaining switch power budget for the equipment at the factory.
Incorrect Answers
B:That behavior applies when engineers “Create an SVI with a gateway IP”; the different operation “Allocate PoE power to a camera port” is intended to power a supported endpoint over its Ethernet connection without a local adapter. That different feature is verified by inspect the SVI addressing and corresponding connected route in the routing table; for “Allocate PoE power to a camera port” on a production FortiSwitch fabric, the relevant evidence is to check delivered watts, endpoint PoE class and remaining switch power budget.
C:This outcome would be relevant to “Configure VRRP on routed interfaces” at the factory, not the task “Allocate PoE power to a camera port”; the other task is to provide a shared default-gateway address resilient to one router failing. The action “Allocate PoE power to a camera port” targets a different result: the switch PoE subsystem supplies negotiated electrical power within the model's available budget; the proposed alternative would instead be checked by check VRRP master state and failover behavior for the virtual gateway.
D:That behavior applies when engineers “Replicate Ethernet broadcast within a broadcast domain”; the different operation “Allocate PoE power to a camera port” is intended to power a supported endpoint over its Ethernet connection without a local adapter. That different feature is verified by capture the broadcast on another member of the same VLAN but not on a different VLAN; for “Allocate PoE power to a camera port” on a production FortiSwitch fabric, the relevant evidence is to check delivered watts, endpoint PoE class and remaining switch power budget.
Question 176
On a newly racked distribution unit at the distribution floor, the team reports that it has configured “Allocate PoE power to a camera port.” Which verification provides the strongest direct evidence that the intended function is working?
- Inspect multicast-group memberships and listener-facing interfaces
- Trace the relayed DHCP transaction and inspect the relay target on the SVI
- Review LACP operational members and negotiated actor/partner status
- Check delivered watts, endpoint PoE class and remaining switch power budget
Explanation
Correct Answer
D:This is the precise control because the switch PoE subsystem supplies negotiated electrical power within the model's available budget. Directly measuring that result demonstrates whether the step to power a supported endpoint over its Ethernet connection without a local adapter succeeded on a newly racked distribution unit.
Incorrect Answers
A:This check is suited to “Enable IGMP snooping for multicast VLANs” when trying to avoid flooding subscribed multicast traffic to every access port, not to verify “Allocate PoE power to a camera port” at the distribution floor. Checking “Allocate PoE power to a camera port” at the distribution floor requires evidence of its own mechanism: the switch PoE subsystem supplies negotiated electrical power within the model's available budget; that is not the outcome measured by “Enable IGMP snooping for multicast VLANs”.
B:The proposed check concerns “Enable DHCP relay on an SVI” rather than “Allocate PoE power to a camera port”: a relay forwards DHCP requests to a configured remote server rather than offering its own address pool. For “Allocate PoE power to a camera port” on a newly racked distribution unit, a better test would be to check delivered watts, endpoint PoE class and remaining switch power budget, which targets power a supported endpoint over its Ethernet connection without a local adapter rather than the alternative diagnostic “Enable DHCP relay on an SVI”.
C:This check is suited to “Use LACP to build a trunk” when trying to combine physical Ethernet links into one negotiated logical channel, not to verify “Allocate PoE power to a camera port” at the distribution floor. Checking “Allocate PoE power to a camera port” at the distribution floor requires evidence of its own mechanism: the switch PoE subsystem supplies negotiated electrical power within the model's available budget; that is not the outcome measured by “Use LACP to build a trunk”.
Question 177
An administrator responsible for two distribution switches in the media studio must avoid flooding subscribed multicast traffic to every access port. Which configuration best matches that precise goal?
- Establish BGP peering for prefix exchange
- Flood unknown unicast only within its VLAN
- Learn source MAC addresses per VLAN
- Enable IGMP snooping for multicast VLANs
- Enable OSPF adjacency on routed interfaces
Explanation
Correct Answer
D:The implementation works because the switch learns IGMP group membership and forwards multicast to interested ports. This distinction is material to the media studio, where the stated goal is to avoid flooding subscribed multicast traffic to every access port.
Incorrect Answers
A:Compared with the requested “Enable IGMP snooping for multicast VLANs” at the media studio, this would exchange policy-controlled routing information with an external routing peer instead: BGP maintains sessions with configured neighbors and selects routes using its path attributes. At the media studio, the operational proof would instead be to inspect multicast-group memberships and listener-facing interfaces, whereas “Establish BGP peering for prefix exchange” is validated by a different test: inspect BGP neighbor session state and the prefix received from the remote autonomous system.
B:Compared with the requested “Enable IGMP snooping for multicast VLANs” at the media studio, this would deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary instead: unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain. At the media studio, the operational proof would instead be to inspect multicast-group memberships and listener-facing interfaces, whereas “Flood unknown unicast only within its VLAN” is validated by a different test: clear a learned destination and observe initial flooding only to permitted VLAN members.
C:Compared with the requested “Enable IGMP snooping for multicast VLANs” at the media studio, this would forward future unicast traffic efficiently to a known endpoint instead: the switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN. At the media studio, the operational proof would instead be to inspect multicast-group memberships and listener-facing interfaces, whereas “Learn source MAC addresses per VLAN” is validated by a different test: inspect the learned MAC table for VLAN and ingress-port association.
E:For the media studio, “Enable OSPF adjacency on routed interfaces” is a different type of control from “Enable IGMP snooping for multicast VLANs”: OSPF forms neighbor relationships and advertises reachable prefixes within configured areas. Unlike the requested feature, that setting addresses the need to exchange dynamic route information with neighboring Layer 3 devices, not the objective to avoid flooding subscribed multicast traffic to every access port.
Question 178
A switch change for the data hall consists of this step: enable IGMP snooping for multicast VLANs. Which behavior reflects the purpose of that change?
- VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet
- A switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled
- The switch learns IGMP group membership and forwards multicast to interested ports
- Broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port
Explanation
Correct Answer
C:Given the described goal, the configured operation is meant to avoid flooding subscribed multicast traffic to every access port. The most relevant validation is to inspect multicast-group memberships and listener-facing interfaces for the equipment at the data hall.
Incorrect Answers
A:This outcome would be relevant to “Configure VRRP on routed interfaces” at the data hall, not the task “Enable IGMP snooping for multicast VLANs”; the other task is to provide a shared default-gateway address resilient to one router failing. The action “Enable IGMP snooping for multicast VLANs” targets a different result: the switch learns IGMP group membership and forwards multicast to interested ports; the proposed alternative would instead be checked by check VRRP master state and failover behavior for the virtual gateway.
B:That behavior applies when engineers “Create an SVI with a gateway IP”; the different operation “Enable IGMP snooping for multicast VLANs” is intended to avoid flooding subscribed multicast traffic to every access port. That different feature is verified by inspect the SVI addressing and corresponding connected route in the routing table; for “Enable IGMP snooping for multicast VLANs” on a staging FortiSwitch, the relevant evidence is to inspect multicast-group memberships and listener-facing interfaces.
D:That behavior applies when engineers “Replicate Ethernet broadcast within a broadcast domain”; the different operation “Enable IGMP snooping for multicast VLANs” is intended to avoid flooding subscribed multicast traffic to every access port. That different feature is verified by capture the broadcast on another member of the same VLAN but not on a different VLAN; for “Enable IGMP snooping for multicast VLANs” on a staging FortiSwitch, the relevant evidence is to inspect multicast-group memberships and listener-facing interfaces.
Question 179
The work order to avoid flooding subscribed multicast traffic to every access port is marked complete on a carefully segmented Layer 2 network. Which observation most directly tests the completed configuration?
- Check delivered watts, endpoint PoE class and remaining switch power budget
- Inspect multicast-group memberships and listener-facing interfaces
- Review LACP operational members and negotiated actor/partner status
- Trace the relayed DHCP transaction and inspect the relay target on the SVI
Explanation
Correct Answer
B:The switch behavior that matters is: the switch learns IGMP group membership and forwards multicast to interested ports. Directly measuring that result demonstrates whether the step to avoid flooding subscribed multicast traffic to every access port succeeded on a carefully segmented Layer 2 network.
Incorrect Answers
A:This check is suited to “Allocate PoE power to a camera port” when trying to power a supported endpoint over its Ethernet connection without a local adapter, not to verify “Enable IGMP snooping for multicast VLANs” at the development floor. Checking “Enable IGMP snooping for multicast VLANs” at the development floor requires evidence of its own mechanism: the switch learns IGMP group membership and forwards multicast to interested ports; that is not the outcome measured by “Allocate PoE power to a camera port”.
C:This check is suited to “Use LACP to build a trunk” when trying to combine physical Ethernet links into one negotiated logical channel, not to verify “Enable IGMP snooping for multicast VLANs” at the development floor. Checking “Enable IGMP snooping for multicast VLANs” at the development floor requires evidence of its own mechanism: the switch learns IGMP group membership and forwards multicast to interested ports; that is not the outcome measured by “Use LACP to build a trunk”.
D:The proposed check concerns “Enable DHCP relay on an SVI” rather than “Enable IGMP snooping for multicast VLANs”: a relay forwards DHCP requests to a configured remote server rather than offering its own address pool. For “Enable IGMP snooping for multicast VLANs” on a carefully segmented Layer 2 network, a better test would be to inspect multicast-group memberships and listener-facing interfaces, which targets avoid flooding subscribed multicast traffic to every access port rather than the alternative diagnostic “Enable DHCP relay on an SVI”.
Question 180
Four FortiSwitch units in the warehouse share an MSTP instance. Their bridge IDs use these priority/MAC combinations: FSW-A: 8192, 02:00:00:00:00:16; FSW-B: 12288, 02:00:00:01:02:23; FSW-C: 16384, 02:00:00:02:04:30; FSW-D: 20480, 02:00:00:03:06:3d. Assuming all advertise and see each other, which switch becomes the root?
- FSW-D
- FSW-B
- FSW-A
- FSW-C
Explanation
Correct Answer
C:For the warehouse, the winning bridge ID compares priority 8192 first, using MAC 02:00:00:00:00:16 to break any priority tie. FSW-A has the lowest complete bridge ID and therefore becomes root.
Incorrect Answers
A:FSW-D advertises priority 20480 and MAC 02:00:00:03:06:3d, whereas FSW-A advertises the superior bridge ID with priority 8192 and MAC 02:00:00:00:00:16. The priority-then-MAC comparison therefore rejects this specific candidate.
B:FSW-B advertises priority 12288 and MAC 02:00:00:01:02:23, whereas FSW-A advertises the superior bridge ID with priority 8192 and MAC 02:00:00:00:00:16. The priority-then-MAC comparison therefore rejects this specific candidate.
D:FSW-C advertises priority 16384 and MAC 02:00:00:02:04:30, whereas FSW-A advertises the superior bridge ID with priority 8192 and MAC 02:00:00:00:00:16. The priority-then-MAC comparison therefore rejects this specific candidate.