Fortinet NSE5_FSW_AD-7.6 (Fortinet NSE 5 - FortiSwitch 7.6 Administrator) Practice Test 16

Question 150

During a change window in the media studio, engineers are asked to reach all eligible peers for a local Layer 2 discovery request. What should they configure rather than using a feature for an adjacent purpose?

  1. Replicate Ethernet broadcast within a broadcast domain
  2. Learn source MAC addresses per VLAN
  3. Enable IGMP snooping for multicast VLANs
  4. Enable OSPF adjacency on routed interfaces

Explanation

Correct Answer

A:

The critical distinction is that broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port. The operator can test this claim by the specific check: capture the broadcast on another member of the same VLAN but not on a different VLAN.

Incorrect Answers

B:

Compared with the requested “Replicate Ethernet broadcast within a broadcast domain” at the media studio, this would forward future unicast traffic efficiently to a known endpoint instead: the switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN. At the media studio, the operational proof would instead be to capture the broadcast on another member of the same VLAN but not on a different VLAN, whereas “Learn source MAC addresses per VLAN” is validated by a different test: inspect the learned MAC table for VLAN and ingress-port association.

C:

For the media studio, “Enable IGMP snooping for multicast VLANs” is a different type of control from “Replicate Ethernet broadcast within a broadcast domain”: the switch learns IGMP group membership and forwards multicast to interested ports. Unlike the requested feature, that setting addresses the need to avoid flooding subscribed multicast traffic to every access port, not the objective to reach all eligible peers for a local Layer 2 discovery request.

D:

Compared with the requested “Replicate Ethernet broadcast within a broadcast domain” at the media studio, this would exchange dynamic route information with neighboring Layer 3 devices instead: OSPF forms neighbor relationships and advertises reachable prefixes within configured areas. At the media studio, the operational proof would instead be to capture the broadcast on another member of the same VLAN but not on a different VLAN, whereas “Enable OSPF adjacency on routed interfaces” is validated by a different test: check OSPF neighbor state and learned routes for the intended area.

Question 151

A colleague asks about the effect of “Replicate Ethernet broadcast within a broadcast domain” on a FortiLink-managed access switch. Which behavior best characterizes that feature?

  1. Broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port
  2. BGP maintains sessions with configured neighbors and selects routes using its path attributes
  3. Unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain
  4. VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet

Explanation

Correct Answer

A:

That setting is appropriate here because the configured operation is meant to reach all eligible peers for a local Layer 2 discovery request. The most relevant validation is to capture the broadcast on another member of the same VLAN but not on a different VLAN for the equipment at the retail site.

Incorrect Answers

B:

That behavior applies when engineers “Establish BGP peering for prefix exchange”; the different operation “Replicate Ethernet broadcast within a broadcast domain” is intended to reach all eligible peers for a local Layer 2 discovery request. That different feature is verified by inspect BGP neighbor session state and the prefix received from the remote autonomous system; for “Replicate Ethernet broadcast within a broadcast domain” on a FortiLink-managed access switch, the relevant evidence is to capture the broadcast on another member of the same VLAN but not on a different VLAN.

C:

This outcome would be relevant to “Flood unknown unicast only within its VLAN” at the retail site, not the task “Replicate Ethernet broadcast within a broadcast domain”; the other task is to deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary. The action “Replicate Ethernet broadcast within a broadcast domain” targets a different result: broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port; the proposed alternative would instead be checked by clear a learned destination and observe initial flooding only to permitted VLAN members.

D:

That behavior applies when engineers “Configure VRRP on routed interfaces”; the different operation “Replicate Ethernet broadcast within a broadcast domain” is intended to reach all eligible peers for a local Layer 2 discovery request. That different feature is verified by check VRRP master state and failover behavior for the virtual gateway; for “Replicate Ethernet broadcast within a broadcast domain” on a FortiLink-managed access switch, the relevant evidence is to capture the broadcast on another member of the same VLAN but not on a different VLAN.

Question 152

On a switch linked to a FortiGate running FortiOS 7.6 at the airport office, the team reports that it has configured “Replicate Ethernet broadcast within a broadcast domain.” Which verification provides the strongest direct evidence that the intended function is working?

  1. Review LACP operational members and negotiated actor/partner status
  2. Inspect the SVI addressing and corresponding connected route in the routing table
  3. Trace the relayed DHCP transaction and inspect the relay target on the SVI
  4. Check VRRP master state and failover behavior for the virtual gateway
  5. Capture the broadcast on another member of the same VLAN but not on a different VLAN

Explanation

Correct Answer

E:

This is the precise control because broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port. Directly measuring that result demonstrates whether the step to reach all eligible peers for a local Layer 2 discovery request succeeded on a switch linked to a FortiGate running FortiOS 7.6.

Incorrect Answers

A:

The proposed check concerns “Use LACP to build a trunk” rather than “Replicate Ethernet broadcast within a broadcast domain”: LACP identifies compatible members and provides link-level redundancy for a logical aggregate. For “Replicate Ethernet broadcast within a broadcast domain” on a switch linked to a FortiGate running FortiOS 7.6, a better test would be to capture the broadcast on another member of the same VLAN but not on a different VLAN, which targets reach all eligible peers for a local Layer 2 discovery request rather than the alternative diagnostic “Use LACP to build a trunk”.

B:

This check is suited to “Create an SVI with a gateway IP” when trying to route traffic from one VLAN subnet toward other routed networks, not to verify “Replicate Ethernet broadcast within a broadcast domain” at the airport office. Checking “Replicate Ethernet broadcast within a broadcast domain” at the airport office requires evidence of its own mechanism: broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port; that is not the outcome measured by “Create an SVI with a gateway IP”.

C:

This check is suited to “Enable DHCP relay on an SVI” when trying to allow clients in one VLAN to reach a DHCP server in a different IP subnet, not to verify “Replicate Ethernet broadcast within a broadcast domain” at the airport office. Checking “Replicate Ethernet broadcast within a broadcast domain” at the airport office requires evidence of its own mechanism: broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port; that is not the outcome measured by “Enable DHCP relay on an SVI”.

D:

The proposed check concerns “Configure VRRP on routed interfaces” rather than “Replicate Ethernet broadcast within a broadcast domain”: VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet. For “Replicate Ethernet broadcast within a broadcast domain” on a switch linked to a FortiGate running FortiOS 7.6, a better test would be to capture the broadcast on another member of the same VLAN but not on a different VLAN, which targets reach all eligible peers for a local Layer 2 discovery request rather than the alternative diagnostic “Configure VRRP on routed interfaces”.

Question 153

For the operations center, the network team needs to route traffic from one VLAN subnet toward other routed networks. Which change is the most direct way to implement that requirement on a switch serving a high-density endpoint area?

  1. Enable IGMP snooping for multicast VLANs
  2. Enable OSPF adjacency on routed interfaces
  3. Create an SVI with a gateway IP
  4. Install a static route

Explanation

Correct Answer

C:

The implementation works because a switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled. This distinction is material to the operations center, where the stated goal is to route traffic from one VLAN subnet toward other routed networks.

Incorrect Answers

A:

Compared with the requested “Create an SVI with a gateway IP” at the operations center, this would avoid flooding subscribed multicast traffic to every access port instead: the switch learns IGMP group membership and forwards multicast to interested ports. At the operations center, the operational proof would instead be to inspect the SVI addressing and corresponding connected route in the routing table, whereas “Enable IGMP snooping for multicast VLANs” is validated by a different test: inspect multicast-group memberships and listener-facing interfaces.

B:

Compared with the requested “Create an SVI with a gateway IP” at the operations center, this would exchange dynamic route information with neighboring Layer 3 devices instead: OSPF forms neighbor relationships and advertises reachable prefixes within configured areas. At the operations center, the operational proof would instead be to inspect the SVI addressing and corresponding connected route in the routing table, whereas “Enable OSPF adjacency on routed interfaces” is validated by a different test: check OSPF neighbor state and learned routes for the intended area.

D:

For the operations center, “Install a static route” is a different type of control from “Create an SVI with a gateway IP”: a static route adds an operator-defined forwarding path subject to route selection and reachability. Unlike the requested feature, that setting addresses the need to give the switch a manually controlled next hop for a known remote prefix, not the objective to route traffic from one VLAN subnet toward other routed networks.

Question 154

During validation of a managed switch running FortiSwitchOS 7.6 at the warehouse, the team asks what the change “Create an SVI with a gateway IP” actually does. Which outcome is correct?

  1. Unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain
  2. A switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled
  3. The switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN
  4. BGP maintains sessions with configured neighbors and selects routes using its path attributes

Explanation

Correct Answer

B:

Given the described goal, the configured operation is meant to route traffic from one VLAN subnet toward other routed networks. The most relevant validation is to inspect the SVI addressing and corresponding connected route in the routing table for the equipment at the warehouse.

Incorrect Answers

A:

That behavior applies when engineers “Flood unknown unicast only within its VLAN”; the different operation “Create an SVI with a gateway IP” is intended to route traffic from one VLAN subnet toward other routed networks. That different feature is verified by clear a learned destination and observe initial flooding only to permitted VLAN members; for “Create an SVI with a gateway IP” on a managed switch running FortiSwitchOS 7.6, the relevant evidence is to inspect the SVI addressing and corresponding connected route in the routing table.

C:

That behavior applies when engineers “Learn source MAC addresses per VLAN”; the different operation “Create an SVI with a gateway IP” is intended to route traffic from one VLAN subnet toward other routed networks. That different feature is verified by inspect the learned MAC table for VLAN and ingress-port association; for “Create an SVI with a gateway IP” on a managed switch running FortiSwitchOS 7.6, the relevant evidence is to inspect the SVI addressing and corresponding connected route in the routing table.

D:

This outcome would be relevant to “Establish BGP peering for prefix exchange” at the warehouse, not the task “Create an SVI with a gateway IP”; the other task is to exchange policy-controlled routing information with an external routing peer. The action “Create an SVI with a gateway IP” targets a different result: a switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled; the proposed alternative would instead be checked by inspect BGP neighbor session state and the prefix received from the remote autonomous system.

Question 155

The work order to route traffic from one VLAN subnet toward other routed networks is marked complete on a remote FortiSwitch installation. Which observation most directly tests the completed configuration?

  1. Review LACP operational members and negotiated actor/partner status
  2. Check VRRP master state and failover behavior for the virtual gateway
  3. Clear a learned destination and observe initial flooding only to permitted VLAN members
  4. Capture the broadcast on another member of the same VLAN but not on a different VLAN
  5. Inspect the SVI addressing and corresponding connected route in the routing table

Explanation

Correct Answer

E:

The switch behavior that matters is: a switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled. Directly measuring that result demonstrates whether the step to route traffic from one VLAN subnet toward other routed networks succeeded on a remote FortiSwitch installation.

Incorrect Answers

A:

This check is suited to “Use LACP to build a trunk” when trying to combine physical Ethernet links into one negotiated logical channel, not to verify “Create an SVI with a gateway IP” at the headquarters. Checking “Create an SVI with a gateway IP” at the headquarters requires evidence of its own mechanism: a switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled; that is not the outcome measured by “Use LACP to build a trunk”.

B:

This check is suited to “Configure VRRP on routed interfaces” when trying to provide a shared default-gateway address resilient to one router failing, not to verify “Create an SVI with a gateway IP” at the headquarters. Checking “Create an SVI with a gateway IP” at the headquarters requires evidence of its own mechanism: a switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled; that is not the outcome measured by “Configure VRRP on routed interfaces”.

C:

The proposed check concerns “Flood unknown unicast only within its VLAN” rather than “Create an SVI with a gateway IP”: unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain. For “Create an SVI with a gateway IP” on a remote FortiSwitch installation, a better test would be to inspect the SVI addressing and corresponding connected route in the routing table, which targets route traffic from one VLAN subnet toward other routed networks rather than the alternative diagnostic “Flood unknown unicast only within its VLAN”.

D:

The proposed check concerns “Replicate Ethernet broadcast within a broadcast domain” rather than “Create an SVI with a gateway IP”: broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port. For “Create an SVI with a gateway IP” on a remote FortiSwitch installation, a better test would be to inspect the SVI addressing and corresponding connected route in the routing table, which targets route traffic from one VLAN subnet toward other routed networks rather than the alternative diagnostic “Replicate Ethernet broadcast within a broadcast domain”.

Question 156

A network architect documents a single goal for an endpoint-facing FortiSwitch port: allow clients in one VLAN to reach a DHCP server in a different IP subnet. Which listed procedure provides that capability?

  1. Configure VRRP on routed interfaces
  2. Enable DHCP relay on an SVI
  3. Establish BGP peering for prefix exchange
  4. Flood unknown unicast only within its VLAN

Explanation

Correct Answer

B:

At this network boundary, a relay forwards DHCP requests to a configured remote server rather than offering its own address pool. The operator can test this claim by the specific check: trace the relayed DHCP transaction and inspect the relay target on the SVI.

Incorrect Answers

A:

Compared with the requested “Enable DHCP relay on an SVI” at the hospital wing, this would provide a shared default-gateway address resilient to one router failing instead: VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet. At the hospital wing, the operational proof would instead be to trace the relayed DHCP transaction and inspect the relay target on the SVI, whereas “Configure VRRP on routed interfaces” is validated by a different test: check VRRP master state and failover behavior for the virtual gateway.

C:

For the hospital wing, “Establish BGP peering for prefix exchange” is a different type of control from “Enable DHCP relay on an SVI”: BGP maintains sessions with configured neighbors and selects routes using its path attributes. Unlike the requested feature, that setting addresses the need to exchange policy-controlled routing information with an external routing peer, not the objective to allow clients in one VLAN to reach a DHCP server in a different IP subnet.

D:

Compared with the requested “Enable DHCP relay on an SVI” at the hospital wing, this would deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary instead: unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain. At the hospital wing, the operational proof would instead be to trace the relayed DHCP transaction and inspect the relay target on the SVI, whereas “Flood unknown unicast only within its VLAN” is validated by a different test: clear a learned destination and observe initial flooding only to permitted VLAN members.

Question 157

Before applying the planned operation “Enable DHCP relay on an SVI” at the factory, the administrator must predict its impact. Which prediction is sound?

  1. A switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled
  2. A relay forwards DHCP requests to a configured remote server rather than offering its own address pool
  3. LACP identifies compatible members and provides link-level redundancy for a logical aggregate
  4. Broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port

Explanation

Correct Answer

B:

In this deployment, the configured operation is meant to allow clients in one VLAN to reach a DHCP server in a different IP subnet. The most relevant validation is to trace the relayed DHCP transaction and inspect the relay target on the SVI for the equipment at the factory.

Incorrect Answers

A:

That behavior applies when engineers “Create an SVI with a gateway IP”; the different operation “Enable DHCP relay on an SVI” is intended to allow clients in one VLAN to reach a DHCP server in a different IP subnet. That different feature is verified by inspect the SVI addressing and corresponding connected route in the routing table; for “Enable DHCP relay on an SVI” on a recently upgraded FortiSwitch, the relevant evidence is to trace the relayed DHCP transaction and inspect the relay target on the SVI.

C:

This outcome would be relevant to “Use LACP to build a trunk” at the factory, not the task “Enable DHCP relay on an SVI”; the other task is to combine physical Ethernet links into one negotiated logical channel. The action “Enable DHCP relay on an SVI” targets a different result: a relay forwards DHCP requests to a configured remote server rather than offering its own address pool; the proposed alternative would instead be checked by review LACP operational members and negotiated actor/partner status.

D:

That behavior applies when engineers “Replicate Ethernet broadcast within a broadcast domain”; the different operation “Enable DHCP relay on an SVI” is intended to allow clients in one VLAN to reach a DHCP server in a different IP subnet. That different feature is verified by capture the broadcast on another member of the same VLAN but not on a different VLAN; for “Enable DHCP relay on an SVI” on a recently upgraded FortiSwitch, the relevant evidence is to trace the relayed DHCP transaction and inspect the relay target on the SVI.

Question 158

An auditor wants operational evidence for the switch action “Enable DHCP relay on an SVI” at the distribution floor. Which check is relevant?

  1. Trace the relayed DHCP transaction and inspect the relay target on the SVI
  2. Inspect the routing table for the route prefix, next hop and selected forwarding entry
  3. Check delivered watts, endpoint PoE class and remaining switch power budget
  4. Inspect multicast-group memberships and listener-facing interfaces

Explanation

Correct Answer

A:

For the stated requirement, a relay forwards DHCP requests to a configured remote server rather than offering its own address pool. Directly measuring that result demonstrates whether the step to allow clients in one VLAN to reach a DHCP server in a different IP subnet succeeded on a FortiLink-managed access switch.

Incorrect Answers

B:

The proposed check concerns “Install a static route” rather than “Enable DHCP relay on an SVI”: a static route adds an operator-defined forwarding path subject to route selection and reachability. For “Enable DHCP relay on an SVI” on a FortiLink-managed access switch, a better test would be to trace the relayed DHCP transaction and inspect the relay target on the SVI, which targets allow clients in one VLAN to reach a DHCP server in a different IP subnet rather than the alternative diagnostic “Install a static route”.

C:

This check is suited to “Allocate PoE power to a camera port” when trying to power a supported endpoint over its Ethernet connection without a local adapter, not to verify “Enable DHCP relay on an SVI” at the distribution floor. Checking “Enable DHCP relay on an SVI” at the distribution floor requires evidence of its own mechanism: a relay forwards DHCP requests to a configured remote server rather than offering its own address pool; that is not the outcome measured by “Allocate PoE power to a camera port”.

D:

This check is suited to “Enable IGMP snooping for multicast VLANs” when trying to avoid flooding subscribed multicast traffic to every access port, not to verify “Enable DHCP relay on an SVI” at the distribution floor. Checking “Enable DHCP relay on an SVI” at the distribution floor requires evidence of its own mechanism: a relay forwards DHCP requests to a configured remote server rather than offering its own address pool; that is not the outcome measured by “Enable IGMP snooping for multicast VLANs”.

Question 159

At the media studio, a technician is choosing between several switching features to give the switch a manually controlled next hop for a known remote prefix. Which one belongs in the implementation plan?

  1. Flood unknown unicast only within its VLAN
  2. Install a static route
  3. Use LACP to build a trunk
  4. Replicate Ethernet broadcast within a broadcast domain
  5. Configure VRRP on routed interfaces

Explanation

Correct Answer

B:

The deciding detail is that a static route adds an operator-defined forwarding path subject to route selection and reachability. This distinction is material to the media studio, where the stated goal is to give the switch a manually controlled next hop for a known remote prefix.

Incorrect Answers

A:

Compared with the requested “Install a static route” at the media studio, this would deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary instead: unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain. At the media studio, the operational proof would instead be to inspect the routing table for the route prefix, next hop and selected forwarding entry, whereas “Flood unknown unicast only within its VLAN” is validated by a different test: clear a learned destination and observe initial flooding only to permitted VLAN members.

C:

Compared with the requested “Install a static route” at the media studio, this would combine physical Ethernet links into one negotiated logical channel instead: LACP identifies compatible members and provides link-level redundancy for a logical aggregate. At the media studio, the operational proof would instead be to inspect the routing table for the route prefix, next hop and selected forwarding entry, whereas “Use LACP to build a trunk” is validated by a different test: review LACP operational members and negotiated actor/partner status.

D:

Compared with the requested “Install a static route” at the media studio, this would reach all eligible peers for a local Layer 2 discovery request instead: broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port. At the media studio, the operational proof would instead be to inspect the routing table for the route prefix, next hop and selected forwarding entry, whereas “Replicate Ethernet broadcast within a broadcast domain” is validated by a different test: capture the broadcast on another member of the same VLAN but not on a different VLAN.

E:

For the media studio, “Configure VRRP on routed interfaces” is a different type of control from “Install a static route”: VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet. Unlike the requested feature, that setting addresses the need to provide a shared default-gateway address resilient to one router failing, not the objective to give the switch a manually controlled next hop for a known remote prefix.

Question 160

During validation of a switch serving a high-density endpoint area at the retail site, the team asks what the change “Install a static route” actually does. Which outcome is correct?

  1. A static route adds an operator-defined forwarding path subject to route selection and reachability
  2. The switch PoE subsystem supplies negotiated electrical power within the model's available budget
  3. A relay forwards DHCP requests to a configured remote server rather than offering its own address pool
  4. A switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled

Explanation

Correct Answer

A:

The relevant mechanism is: the configured operation is meant to give the switch a manually controlled next hop for a known remote prefix. The most relevant validation is to inspect the routing table for the route prefix, next hop and selected forwarding entry for the equipment at the retail site.

Incorrect Answers

B:

This outcome would be relevant to “Allocate PoE power to a camera port” at the retail site, not the task “Install a static route”; the other task is to power a supported endpoint over its Ethernet connection without a local adapter. The action “Install a static route” targets a different result: a static route adds an operator-defined forwarding path subject to route selection and reachability; the proposed alternative would instead be checked by check delivered watts, endpoint PoE class and remaining switch power budget.

C:

That behavior applies when engineers “Enable DHCP relay on an SVI”; the different operation “Install a static route” is intended to give the switch a manually controlled next hop for a known remote prefix. That different feature is verified by trace the relayed DHCP transaction and inspect the relay target on the SVI; for “Install a static route” on a switch serving a high-density endpoint area, the relevant evidence is to inspect the routing table for the route prefix, next hop and selected forwarding entry.

D:

That behavior applies when engineers “Create an SVI with a gateway IP”; the different operation “Install a static route” is intended to give the switch a manually controlled next hop for a known remote prefix. That different feature is verified by inspect the SVI addressing and corresponding connected route in the routing table; for “Install a static route” on a switch serving a high-density endpoint area, the relevant evidence is to inspect the routing table for the route prefix, next hop and selected forwarding entry.

Fortinet NSE 5 - FortiSwitch 7.6 Administrator (NSE5_FSW_AD-7.6) Practice Tests