Fortinet NSE5_FSW_AD-7.6 (Fortinet NSE 5 - FortiSwitch 7.6 Administrator) Practice Test 17

Question 160

During validation of a switch serving a high-density endpoint area at the retail site, the team asks what the change “Install a static route” actually does. Which outcome is correct?

  1. A static route adds an operator-defined forwarding path subject to route selection and reachability
  2. The switch PoE subsystem supplies negotiated electrical power within the model's available budget
  3. A relay forwards DHCP requests to a configured remote server rather than offering its own address pool
  4. A switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled

Explanation

Correct Answer

A:

The relevant mechanism is: the configured operation is meant to give the switch a manually controlled next hop for a known remote prefix. The most relevant validation is to inspect the routing table for the route prefix, next hop and selected forwarding entry for the equipment at the retail site.

Incorrect Answers

B:

This outcome would be relevant to “Allocate PoE power to a camera port” at the retail site, not the task “Install a static route”; the other task is to power a supported endpoint over its Ethernet connection without a local adapter. The action “Install a static route” targets a different result: a static route adds an operator-defined forwarding path subject to route selection and reachability; the proposed alternative would instead be checked by check delivered watts, endpoint PoE class and remaining switch power budget.

C:

That behavior applies when engineers “Enable DHCP relay on an SVI”; the different operation “Install a static route” is intended to give the switch a manually controlled next hop for a known remote prefix. That different feature is verified by trace the relayed DHCP transaction and inspect the relay target on the SVI; for “Install a static route” on a switch serving a high-density endpoint area, the relevant evidence is to inspect the routing table for the route prefix, next hop and selected forwarding entry.

D:

That behavior applies when engineers “Create an SVI with a gateway IP”; the different operation “Install a static route” is intended to give the switch a manually controlled next hop for a known remote prefix. That different feature is verified by inspect the SVI addressing and corresponding connected route in the routing table; for “Install a static route” on a switch serving a high-density endpoint area, the relevant evidence is to inspect the routing table for the route prefix, next hop and selected forwarding entry.

Question 161

A technician says “Install a static route” has solved the issue at the airport office. Which diagnostic step would substantiate that claim?

  1. Inspect the routing table for the route prefix, next hop and selected forwarding entry
  2. Inspect multicast-group memberships and listener-facing interfaces
  3. Inspect the learned MAC table for VLAN and ingress-port association
  4. Check OSPF neighbor state and learned routes for the intended area

Explanation

Correct Answer

A:

This approach fits because a static route adds an operator-defined forwarding path subject to route selection and reachability. Directly measuring that result demonstrates whether the step to give the switch a manually controlled next hop for a known remote prefix succeeded on a managed switch running FortiSwitchOS 7.6.

Incorrect Answers

B:

This check is suited to “Enable IGMP snooping for multicast VLANs” when trying to avoid flooding subscribed multicast traffic to every access port, not to verify “Install a static route” at the airport office. Checking “Install a static route” at the airport office requires evidence of its own mechanism: a static route adds an operator-defined forwarding path subject to route selection and reachability; that is not the outcome measured by “Enable IGMP snooping for multicast VLANs”.

C:

This check is suited to “Learn source MAC addresses per VLAN” when trying to forward future unicast traffic efficiently to a known endpoint, not to verify “Install a static route” at the airport office. Checking “Install a static route” at the airport office requires evidence of its own mechanism: a static route adds an operator-defined forwarding path subject to route selection and reachability; that is not the outcome measured by “Learn source MAC addresses per VLAN”.

D:

The proposed check concerns “Enable OSPF adjacency on routed interfaces” rather than “Install a static route”: OSPF forms neighbor relationships and advertises reachable prefixes within configured areas. For “Install a static route” on a managed switch running FortiSwitchOS 7.6, a better test would be to inspect the routing table for the route prefix, next hop and selected forwarding entry, which targets give the switch a manually controlled next hop for a known remote prefix rather than the alternative diagnostic “Enable OSPF adjacency on routed interfaces”.

Question 162

The accepted design for the operations center requires the ability to exchange dynamic route information with neighboring Layer 3 devices. Which switch feature is the closest fit?

  1. Enable OSPF adjacency on routed interfaces
  2. Flood unknown unicast only within its VLAN
  3. Learn source MAC addresses per VLAN
  4. Establish BGP peering for prefix exchange

Explanation

Correct Answer

A:

The critical distinction is that OSPF forms neighbor relationships and advertises reachable prefixes within configured areas. The operator can test this claim by the specific check: check OSPF neighbor state and learned routes for the intended area.

Incorrect Answers

B:

Compared with the requested “Enable OSPF adjacency on routed interfaces” at the operations center, this would deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary instead: unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain. At the operations center, the operational proof would instead be to check OSPF neighbor state and learned routes for the intended area, whereas “Flood unknown unicast only within its VLAN” is validated by a different test: clear a learned destination and observe initial flooding only to permitted VLAN members.

C:

For the operations center, “Learn source MAC addresses per VLAN” is a different type of control from “Enable OSPF adjacency on routed interfaces”: the switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN. Unlike the requested feature, that setting addresses the need to forward future unicast traffic efficiently to a known endpoint, not the objective to exchange dynamic route information with neighboring Layer 3 devices.

D:

Compared with the requested “Enable OSPF adjacency on routed interfaces” at the operations center, this would exchange policy-controlled routing information with an external routing peer instead: BGP maintains sessions with configured neighbors and selects routes using its path attributes. At the operations center, the operational proof would instead be to check OSPF neighbor state and learned routes for the intended area, whereas “Establish BGP peering for prefix exchange” is validated by a different test: inspect BGP neighbor session state and the prefix received from the remote autonomous system.

Question 163

Before applying the planned operation “Enable OSPF adjacency on routed interfaces” at the warehouse, the administrator must predict its impact. Which prediction is sound?

  1. VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet
  2. LACP identifies compatible members and provides link-level redundancy for a logical aggregate
  3. Unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain
  4. OSPF forms neighbor relationships and advertises reachable prefixes within configured areas
  5. Broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port

Explanation

Correct Answer

D:

That setting is appropriate here because the configured operation is meant to exchange dynamic route information with neighboring Layer 3 devices. The most relevant validation is to check OSPF neighbor state and learned routes for the intended area for the equipment at the warehouse.

Incorrect Answers

A:

That behavior applies when engineers “Configure VRRP on routed interfaces”; the different operation “Enable OSPF adjacency on routed interfaces” is intended to exchange dynamic route information with neighboring Layer 3 devices. That different feature is verified by check VRRP master state and failover behavior for the virtual gateway; for “Enable OSPF adjacency on routed interfaces” on an endpoint-facing FortiSwitch port, the relevant evidence is to check OSPF neighbor state and learned routes for the intended area.

B:

That behavior applies when engineers “Use LACP to build a trunk”; the different operation “Enable OSPF adjacency on routed interfaces” is intended to exchange dynamic route information with neighboring Layer 3 devices. That different feature is verified by review LACP operational members and negotiated actor/partner status; for “Enable OSPF adjacency on routed interfaces” on an endpoint-facing FortiSwitch port, the relevant evidence is to check OSPF neighbor state and learned routes for the intended area.

C:

That behavior applies when engineers “Flood unknown unicast only within its VLAN”; the different operation “Enable OSPF adjacency on routed interfaces” is intended to exchange dynamic route information with neighboring Layer 3 devices. That different feature is verified by clear a learned destination and observe initial flooding only to permitted VLAN members; for “Enable OSPF adjacency on routed interfaces” on an endpoint-facing FortiSwitch port, the relevant evidence is to check OSPF neighbor state and learned routes for the intended area.

E:

This outcome would be relevant to “Replicate Ethernet broadcast within a broadcast domain” at the warehouse, not the task “Enable OSPF adjacency on routed interfaces”; the other task is to reach all eligible peers for a local Layer 2 discovery request. The action “Enable OSPF adjacency on routed interfaces” targets a different result: OSPF forms neighbor relationships and advertises reachable prefixes within configured areas; the proposed alternative would instead be checked by capture the broadcast on another member of the same VLAN but not on a different VLAN.

Question 164

After implementing “Enable OSPF adjacency on routed interfaces,” the site engineer needs to assess its actual effect on a standalone FortiSwitch appliance. Which test is the best match?

  1. Inspect the SVI addressing and corresponding connected route in the routing table
  2. Check OSPF neighbor state and learned routes for the intended area
  3. Trace the relayed DHCP transaction and inspect the relay target on the SVI
  4. Check delivered watts, endpoint PoE class and remaining switch power budget

Explanation

Correct Answer

B:

This is the precise control because OSPF forms neighbor relationships and advertises reachable prefixes within configured areas. Directly measuring that result demonstrates whether the step to exchange dynamic route information with neighboring Layer 3 devices succeeded on a standalone FortiSwitch appliance.

Incorrect Answers

A:

This check is suited to “Create an SVI with a gateway IP” when trying to route traffic from one VLAN subnet toward other routed networks, not to verify “Enable OSPF adjacency on routed interfaces” at the remote depot. Checking “Enable OSPF adjacency on routed interfaces” at the remote depot requires evidence of its own mechanism: OSPF forms neighbor relationships and advertises reachable prefixes within configured areas; that is not the outcome measured by “Create an SVI with a gateway IP”.

C:

This check is suited to “Enable DHCP relay on an SVI” when trying to allow clients in one VLAN to reach a DHCP server in a different IP subnet, not to verify “Enable OSPF adjacency on routed interfaces” at the remote depot. Checking “Enable OSPF adjacency on routed interfaces” at the remote depot requires evidence of its own mechanism: OSPF forms neighbor relationships and advertises reachable prefixes within configured areas; that is not the outcome measured by “Enable DHCP relay on an SVI”.

D:

The proposed check concerns “Allocate PoE power to a camera port” rather than “Enable OSPF adjacency on routed interfaces”: the switch PoE subsystem supplies negotiated electrical power within the model's available budget. For “Enable OSPF adjacency on routed interfaces” on a standalone FortiSwitch appliance, a better test would be to check OSPF neighbor state and learned routes for the intended area, which targets exchange dynamic route information with neighboring Layer 3 devices rather than the alternative diagnostic “Allocate PoE power to a camera port”.

Question 165

A deployment review at the branch office identifies this objective: exchange policy-controlled routing information with an external routing peer. Which FortiSwitch operation should be selected?

  1. Establish BGP peering for prefix exchange
  2. Install a static route
  3. Learn source MAC addresses per VLAN
  4. Enable OSPF adjacency on routed interfaces

Explanation

Correct Answer

A:

The implementation works because BGP maintains sessions with configured neighbors and selects routes using its path attributes. This distinction is material to the branch office, where the stated goal is to exchange policy-controlled routing information with an external routing peer.

Incorrect Answers

B:

For the branch office, “Install a static route” is a different type of control from “Establish BGP peering for prefix exchange”: a static route adds an operator-defined forwarding path subject to route selection and reachability. Unlike the requested feature, that setting addresses the need to give the switch a manually controlled next hop for a known remote prefix, not the objective to exchange policy-controlled routing information with an external routing peer.

C:

Compared with the requested “Establish BGP peering for prefix exchange” at the branch office, this would forward future unicast traffic efficiently to a known endpoint instead: the switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN. At the branch office, the operational proof would instead be to inspect BGP neighbor session state and the prefix received from the remote autonomous system, whereas “Learn source MAC addresses per VLAN” is validated by a different test: inspect the learned MAC table for VLAN and ingress-port association.

D:

Compared with the requested “Establish BGP peering for prefix exchange” at the branch office, this would exchange dynamic route information with neighboring Layer 3 devices instead: OSPF forms neighbor relationships and advertises reachable prefixes within configured areas. At the branch office, the operational proof would instead be to inspect BGP neighbor session state and the prefix received from the remote autonomous system, whereas “Enable OSPF adjacency on routed interfaces” is validated by a different test: check OSPF neighbor state and learned routes for the intended area.

Question 166

During validation of a local switch administering branch clients at the factory, the team asks what the change “Establish BGP peering for prefix exchange” actually does. Which outcome is correct?

  1. VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet
  2. OSPF forms neighbor relationships and advertises reachable prefixes within configured areas
  3. BGP maintains sessions with configured neighbors and selects routes using its path attributes
  4. Unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain
  5. Broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port

Explanation

Correct Answer

C:

Given the described goal, the configured operation is meant to exchange policy-controlled routing information with an external routing peer. The most relevant validation is to inspect BGP neighbor session state and the prefix received from the remote autonomous system for the equipment at the factory.

Incorrect Answers

A:

This outcome would be relevant to “Configure VRRP on routed interfaces” at the factory, not the task “Establish BGP peering for prefix exchange”; the other task is to provide a shared default-gateway address resilient to one router failing. The action “Establish BGP peering for prefix exchange” targets a different result: BGP maintains sessions with configured neighbors and selects routes using its path attributes; the proposed alternative would instead be checked by check VRRP master state and failover behavior for the virtual gateway.

B:

That behavior applies when engineers “Enable OSPF adjacency on routed interfaces”; the different operation “Establish BGP peering for prefix exchange” is intended to exchange policy-controlled routing information with an external routing peer. That different feature is verified by check OSPF neighbor state and learned routes for the intended area; for “Establish BGP peering for prefix exchange” on a local switch administering branch clients, the relevant evidence is to inspect BGP neighbor session state and the prefix received from the remote autonomous system.

D:

That behavior applies when engineers “Flood unknown unicast only within its VLAN”; the different operation “Establish BGP peering for prefix exchange” is intended to exchange policy-controlled routing information with an external routing peer. That different feature is verified by clear a learned destination and observe initial flooding only to permitted VLAN members; for “Establish BGP peering for prefix exchange” on a local switch administering branch clients, the relevant evidence is to inspect BGP neighbor session state and the prefix received from the remote autonomous system.

E:

That behavior applies when engineers “Replicate Ethernet broadcast within a broadcast domain”; the different operation “Establish BGP peering for prefix exchange” is intended to exchange policy-controlled routing information with an external routing peer. That different feature is verified by capture the broadcast on another member of the same VLAN but not on a different VLAN; for “Establish BGP peering for prefix exchange” on a local switch administering branch clients, the relevant evidence is to inspect BGP neighbor session state and the prefix received from the remote autonomous system.

Question 167

The change-control ticket for a switch used by multiple office teams requires one validation of the goal to exchange policy-controlled routing information with an external routing peer. Which evidence should be collected?

  1. Inspect BGP neighbor session state and the prefix received from the remote autonomous system
  2. Inspect the SVI addressing and corresponding connected route in the routing table
  3. Check delivered watts, endpoint PoE class and remaining switch power budget
  4. Review LACP operational members and negotiated actor/partner status

Explanation

Correct Answer

A:

The switch behavior that matters is: BGP maintains sessions with configured neighbors and selects routes using its path attributes. Directly measuring that result demonstrates whether the step to exchange policy-controlled routing information with an external routing peer succeeded on a switch used by multiple office teams.

Incorrect Answers

B:

The proposed check concerns “Create an SVI with a gateway IP” rather than “Establish BGP peering for prefix exchange”: a switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled. For “Establish BGP peering for prefix exchange” on a switch used by multiple office teams, a better test would be to inspect BGP neighbor session state and the prefix received from the remote autonomous system, which targets exchange policy-controlled routing information with an external routing peer rather than the alternative diagnostic “Create an SVI with a gateway IP”.

C:

This check is suited to “Allocate PoE power to a camera port” when trying to power a supported endpoint over its Ethernet connection without a local adapter, not to verify “Establish BGP peering for prefix exchange” at the distribution floor. Checking “Establish BGP peering for prefix exchange” at the distribution floor requires evidence of its own mechanism: BGP maintains sessions with configured neighbors and selects routes using its path attributes; that is not the outcome measured by “Allocate PoE power to a camera port”.

D:

This check is suited to “Use LACP to build a trunk” when trying to combine physical Ethernet links into one negotiated logical channel, not to verify “Establish BGP peering for prefix exchange” at the distribution floor. Checking “Establish BGP peering for prefix exchange” at the distribution floor requires evidence of its own mechanism: BGP maintains sessions with configured neighbors and selects routes using its path attributes; that is not the outcome measured by “Use LACP to build a trunk”.

Question 168

On a production FortiSwitch fabric in the media studio, the next task is to provide a shared default-gateway address resilient to one router failing. What is the appropriate configuration decision?

  1. Install a static route
  2. Learn source MAC addresses per VLAN
  3. Enable OSPF adjacency on routed interfaces
  4. Configure VRRP on routed interfaces

Explanation

Correct Answer

D:

At this network boundary, VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet. The operator can test this claim by the specific check: check VRRP master state and failover behavior for the virtual gateway.

Incorrect Answers

A:

For the media studio, “Install a static route” is a different type of control from “Configure VRRP on routed interfaces”: a static route adds an operator-defined forwarding path subject to route selection and reachability. Unlike the requested feature, that setting addresses the need to give the switch a manually controlled next hop for a known remote prefix, not the objective to provide a shared default-gateway address resilient to one router failing.

B:

Compared with the requested “Configure VRRP on routed interfaces” at the media studio, this would forward future unicast traffic efficiently to a known endpoint instead: the switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN. At the media studio, the operational proof would instead be to check VRRP master state and failover behavior for the virtual gateway, whereas “Learn source MAC addresses per VLAN” is validated by a different test: inspect the learned MAC table for VLAN and ingress-port association.

C:

Compared with the requested “Configure VRRP on routed interfaces” at the media studio, this would exchange dynamic route information with neighboring Layer 3 devices instead: OSPF forms neighbor relationships and advertises reachable prefixes within configured areas. At the media studio, the operational proof would instead be to check VRRP master state and failover behavior for the virtual gateway, whereas “Enable OSPF adjacency on routed interfaces” is validated by a different test: check OSPF neighbor state and learned routes for the intended area.

Question 169

Before applying the planned operation “Configure VRRP on routed interfaces” at the retail site, the administrator must predict its impact. Which prediction is sound?

  1. BGP maintains sessions with configured neighbors and selects routes using its path attributes
  2. VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet
  3. Unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain
  4. Broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port

Explanation

Correct Answer

B:

In this deployment, the configured operation is meant to provide a shared default-gateway address resilient to one router failing. The most relevant validation is to check VRRP master state and failover behavior for the virtual gateway for the equipment at the retail site.

Incorrect Answers

A:

This outcome would be relevant to “Establish BGP peering for prefix exchange” at the retail site, not the task “Configure VRRP on routed interfaces”; the other task is to exchange policy-controlled routing information with an external routing peer. The action “Configure VRRP on routed interfaces” targets a different result: VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet; the proposed alternative would instead be checked by inspect BGP neighbor session state and the prefix received from the remote autonomous system.

C:

That behavior applies when engineers “Flood unknown unicast only within its VLAN”; the different operation “Configure VRRP on routed interfaces” is intended to provide a shared default-gateway address resilient to one router failing. That different feature is verified by clear a learned destination and observe initial flooding only to permitted VLAN members; for “Configure VRRP on routed interfaces” on a newly racked distribution unit, the relevant evidence is to check VRRP master state and failover behavior for the virtual gateway.

D:

That behavior applies when engineers “Replicate Ethernet broadcast within a broadcast domain”; the different operation “Configure VRRP on routed interfaces” is intended to provide a shared default-gateway address resilient to one router failing. That different feature is verified by capture the broadcast on another member of the same VLAN but not on a different VLAN; for “Configure VRRP on routed interfaces” on a newly racked distribution unit, the relevant evidence is to check VRRP master state and failover behavior for the virtual gateway.

Question 170

A FortiSwitch engineer in the airport office is documenting successful operation of “Configure VRRP on routed interfaces.” Which measurement or inspection confirms it?

  1. Check VRRP master state and failover behavior for the virtual gateway
  2. Review LACP operational members and negotiated actor/partner status
  3. Inspect the SVI addressing and corresponding connected route in the routing table
  4. Check delivered watts, endpoint PoE class and remaining switch power budget
  5. Capture the broadcast on another member of the same VLAN but not on a different VLAN

Explanation

Correct Answer

A:

For the stated requirement, VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet. Directly measuring that result demonstrates whether the step to provide a shared default-gateway address resilient to one router failing succeeded on an endpoint-facing FortiSwitch port.

Incorrect Answers

B:

This check is suited to “Use LACP to build a trunk” when trying to combine physical Ethernet links into one negotiated logical channel, not to verify “Configure VRRP on routed interfaces” at the airport office. Checking “Configure VRRP on routed interfaces” at the airport office requires evidence of its own mechanism: VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet; that is not the outcome measured by “Use LACP to build a trunk”.

C:

The proposed check concerns “Create an SVI with a gateway IP” rather than “Configure VRRP on routed interfaces”: a switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled. For “Configure VRRP on routed interfaces” on an endpoint-facing FortiSwitch port, a better test would be to check VRRP master state and failover behavior for the virtual gateway, which targets provide a shared default-gateway address resilient to one router failing rather than the alternative diagnostic “Create an SVI with a gateway IP”.

D:

This check is suited to “Allocate PoE power to a camera port” when trying to power a supported endpoint over its Ethernet connection without a local adapter, not to verify “Configure VRRP on routed interfaces” at the airport office. Checking “Configure VRRP on routed interfaces” at the airport office requires evidence of its own mechanism: VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet; that is not the outcome measured by “Allocate PoE power to a camera port”.

E:

The proposed check concerns “Replicate Ethernet broadcast within a broadcast domain” rather than “Configure VRRP on routed interfaces”: broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port. For “Configure VRRP on routed interfaces” on an endpoint-facing FortiSwitch port, a better test would be to check VRRP master state and failover behavior for the virtual gateway, which targets provide a shared default-gateway address resilient to one router failing rather than the alternative diagnostic “Replicate Ethernet broadcast within a broadcast domain”.

Fortinet NSE 5 - FortiSwitch 7.6 Administrator (NSE5_FSW_AD-7.6) Practice Tests