Fortinet NSE5_FSW_AD-7.6 (Fortinet NSE 5 - FortiSwitch 7.6 Administrator) Practice Test 15

Question 140

A FortiSwitch L3 routing table at the airport office has four operational routes: 10.114.178.0/24 [distance 90]; 10.114.0.0/16 [distance 40]; 10.0.0.0/8 [distance 10]; 0.0.0.0/0 [distance 1]. Which entry is used to forward a packet to 10.114.178.219? Assume the next hops are all reachable.

  1. 10.114.178.0/24 via VLAN-A (distance 90)
  2. 10.0.0.0/8 via VLAN-C (distance 10)
  3. 0.0.0.0/0 via VLAN-D (distance 1)
  4. 10.114.0.0/16 via VLAN-B (distance 40)

Explanation

Correct Answer

A:

10.114.178.0/24 contains 10.114.178.219 and is the most specific matching route, regardless of a larger numerical distance.

Incorrect Answers

B:

10.0.0.0/8 is a broader route than 10.114.178.0/24; its distance of 10 cannot beat a longer prefix that matches 10.114.178.219.

C:

0.0.0.0/0 is a broader route than 10.114.178.0/24; its distance of 1 cannot beat a longer prefix that matches 10.114.178.219.

D:

10.114.0.0/16 is a broader route than 10.114.178.0/24; its distance of 40 cannot beat a longer prefix that matches 10.114.178.219.

Question 141

A FortiSwitch L3 routing table at the operations center has four operational routes: 10.121.189.0/24 [distance 30]; 10.121.189.0/24 [distance 80]; 10.121.0.0/16 [distance 5]; 0.0.0.0/0 [distance 1]. Which entry is used to forward a packet to 10.121.189.232? Assume the next hops are all reachable.

  1. 0.0.0.0/0 via VLAN-D (distance 1)
  2. 10.121.189.0/24 via VLAN-A (distance 30)
  3. 10.121.0.0/16 via VLAN-C (distance 5)
  4. 10.121.189.0/24 via VLAN-B (distance 80)

Explanation

Correct Answer

B:

10.121.189.0/24 is a /24 match with distance 30, lower than the competing /24 distance of 80. This selects the preferred route for 10.121.189.232.

Incorrect Answers

A:

0.0.0.0/0 may have a lower distance, but its shorter prefix loses the longest-match comparison for 10.121.189.232.

C:

10.121.0.0/16 may have a lower distance, but its shorter prefix loses the longest-match comparison for 10.121.189.232.

D:

10.121.189.0/24 has the same /24 prefix but distance 80, which is higher than the selected route; both candidates have equal specificity.

Question 142

A FortiSwitch L3 routing table at the warehouse has four operational routes: 10.128.200.0/24 [distance 90]; 10.128.0.0/16 [distance 40]; 10.0.0.0/8 [distance 10]; 0.0.0.0/0 [distance 1]. Which entry is used to forward a packet to 10.128.200.245? Assume the next hops are all reachable.

  1. 10.128.200.0/24 via VLAN-A (distance 90)
  2. 0.0.0.0/0 via VLAN-D (distance 1)
  3. 10.128.0.0/16 via VLAN-B (distance 40)
  4. 10.0.0.0/8 via VLAN-C (distance 10)

Explanation

Correct Answer

A:

10.128.200.0/24 contains 10.128.200.245 and is the most specific matching route, regardless of a larger numerical distance.

Incorrect Answers

B:

0.0.0.0/0 is a broader route than 10.128.200.0/24; its distance of 1 cannot beat a longer prefix that matches 10.128.200.245.

C:

10.128.0.0/16 is a broader route than 10.128.200.0/24; its distance of 40 cannot beat a longer prefix that matches 10.128.200.245.

D:

10.0.0.0/8 is a broader route than 10.128.200.0/24; its distance of 10 cannot beat a longer prefix that matches 10.128.200.245.

Question 143

A FortiSwitch L3 routing table at the headquarters has four operational routes: 10.135.211.0/24 [distance 40]; 10.135.211.0/24 [distance 80]; 10.135.0.0/16 [distance 5]; 0.0.0.0/0 [distance 1]. Which entry is used to forward a packet to 10.135.211.23? Assume the next hops are all reachable.

  1. 0.0.0.0/0 via VLAN-D (distance 1)
  2. 10.135.211.0/24 via VLAN-B (distance 80)
  3. 10.135.211.0/24 via VLAN-A (distance 40)
  4. 10.135.0.0/16 via VLAN-C (distance 5)

Explanation

Correct Answer

C:

10.135.211.0/24 is a /24 match with distance 40, lower than the competing /24 distance of 80. This selects the preferred route for 10.135.211.23.

Incorrect Answers

A:

0.0.0.0/0 may have a lower distance, but its shorter prefix loses the longest-match comparison for 10.135.211.23.

B:

10.135.211.0/24 has the same /24 prefix but distance 80, which is higher than the selected route; both candidates have equal specificity.

D:

10.135.0.0/16 may have a lower distance, but its shorter prefix loses the longest-match comparison for 10.135.211.23.

Question 144

A production incident in the operations center reveals the need to forward future unicast traffic efficiently to a known endpoint. Which targeted FortiSwitch setting or method should the team use?

  1. Replicate Ethernet broadcast within a broadcast domain
  2. Configure VRRP on routed interfaces
  3. Establish BGP peering for prefix exchange
  4. Learn source MAC addresses per VLAN
  5. Create an SVI with a gateway IP

Explanation

Correct Answer

D:

At this network boundary, the switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN. The operator can test this claim by the specific check: inspect the learned MAC table for VLAN and ingress-port association.

Incorrect Answers

A:

For the operations center, “Replicate Ethernet broadcast within a broadcast domain” is a different type of control from “Learn source MAC addresses per VLAN”: broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port. Unlike the requested feature, that setting addresses the need to reach all eligible peers for a local Layer 2 discovery request, not the objective to forward future unicast traffic efficiently to a known endpoint.

B:

Compared with the requested “Learn source MAC addresses per VLAN” at the operations center, this would provide a shared default-gateway address resilient to one router failing instead: VRRP coordinates a virtual IP/MAC and chooses an active router for hosts on a shared subnet. At the operations center, the operational proof would instead be to inspect the learned MAC table for VLAN and ingress-port association, whereas “Configure VRRP on routed interfaces” is validated by a different test: check VRRP master state and failover behavior for the virtual gateway.

C:

Compared with the requested “Learn source MAC addresses per VLAN” at the operations center, this would exchange policy-controlled routing information with an external routing peer instead: BGP maintains sessions with configured neighbors and selects routes using its path attributes. At the operations center, the operational proof would instead be to inspect the learned MAC table for VLAN and ingress-port association, whereas “Establish BGP peering for prefix exchange” is validated by a different test: inspect BGP neighbor session state and the prefix received from the remote autonomous system.

E:

Compared with the requested “Learn source MAC addresses per VLAN” at the operations center, this would route traffic from one VLAN subnet toward other routed networks instead: a switch virtual interface supplies Layer 3 termination for a VLAN where routing is enabled. At the operations center, the operational proof would instead be to inspect the learned MAC table for VLAN and ingress-port association, whereas “Create an SVI with a gateway IP” is validated by a different test: inspect the SVI addressing and corresponding connected route in the routing table.

Question 145

A colleague asks about the effect of “Learn source MAC addresses per VLAN” on a carefully segmented Layer 2 network. Which behavior best characterizes that feature?

  1. LACP identifies compatible members and provides link-level redundancy for a logical aggregate
  2. A relay forwards DHCP requests to a configured remote server rather than offering its own address pool
  3. The switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN
  4. The switch PoE subsystem supplies negotiated electrical power within the model's available budget

Explanation

Correct Answer

C:

In this deployment, the configured operation is meant to forward future unicast traffic efficiently to a known endpoint. The most relevant validation is to inspect the learned MAC table for VLAN and ingress-port association for the equipment at the warehouse.

Incorrect Answers

A:

That behavior applies when engineers “Use LACP to build a trunk”; the different operation “Learn source MAC addresses per VLAN” is intended to forward future unicast traffic efficiently to a known endpoint. That different feature is verified by review LACP operational members and negotiated actor/partner status; for “Learn source MAC addresses per VLAN” on a carefully segmented Layer 2 network, the relevant evidence is to inspect the learned MAC table for VLAN and ingress-port association.

B:

This outcome would be relevant to “Enable DHCP relay on an SVI” at the warehouse, not the task “Learn source MAC addresses per VLAN”; the other task is to allow clients in one VLAN to reach a DHCP server in a different IP subnet. The action “Learn source MAC addresses per VLAN” targets a different result: the switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN; the proposed alternative would instead be checked by trace the relayed DHCP transaction and inspect the relay target on the SVI.

D:

That behavior applies when engineers “Allocate PoE power to a camera port”; the different operation “Learn source MAC addresses per VLAN” is intended to forward future unicast traffic efficiently to a known endpoint. That different feature is verified by check delivered watts, endpoint PoE class and remaining switch power budget; for “Learn source MAC addresses per VLAN” on a carefully segmented Layer 2 network, the relevant evidence is to inspect the learned MAC table for VLAN and ingress-port association.

Question 146

A FortiSwitch engineer in the headquarters is documenting successful operation of “Learn source MAC addresses per VLAN.” Which measurement or inspection confirms it?

  1. Inspect the routing table for the route prefix, next hop and selected forwarding entry
  2. Check OSPF neighbor state and learned routes for the intended area
  3. Inspect multicast-group memberships and listener-facing interfaces
  4. Inspect the learned MAC table for VLAN and ingress-port association

Explanation

Correct Answer

D:

For the stated requirement, the switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN. Directly measuring that result demonstrates whether the step to forward future unicast traffic efficiently to a known endpoint succeeded on a central switching stack.

Incorrect Answers

A:

This check is suited to “Install a static route” when trying to give the switch a manually controlled next hop for a known remote prefix, not to verify “Learn source MAC addresses per VLAN” at the headquarters. Checking “Learn source MAC addresses per VLAN” at the headquarters requires evidence of its own mechanism: the switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN; that is not the outcome measured by “Install a static route”.

B:

This check is suited to “Enable OSPF adjacency on routed interfaces” when trying to exchange dynamic route information with neighboring Layer 3 devices, not to verify “Learn source MAC addresses per VLAN” at the headquarters. Checking “Learn source MAC addresses per VLAN” at the headquarters requires evidence of its own mechanism: the switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN; that is not the outcome measured by “Enable OSPF adjacency on routed interfaces”.

C:

The proposed check concerns “Enable IGMP snooping for multicast VLANs” rather than “Learn source MAC addresses per VLAN”: the switch learns IGMP group membership and forwards multicast to interested ports. For “Learn source MAC addresses per VLAN” on a central switching stack, a better test would be to inspect the learned MAC table for VLAN and ingress-port association, which targets forward future unicast traffic efficiently to a known endpoint rather than the alternative diagnostic “Enable IGMP snooping for multicast VLANs”.

Question 147

The operational requirement for a FortiSwitch connected to the security edge at the hospital wing is to deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary. Which FortiSwitch choice directly targets it?

  1. Allocate PoE power to a camera port
  2. Flood unknown unicast only within its VLAN
  3. Install a static route
  4. Enable DHCP relay on an SVI

Explanation

Correct Answer

B:

The deciding detail is that unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain. This distinction is material to the hospital wing, where the stated goal is to deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary.

Incorrect Answers

A:

Compared with the requested “Flood unknown unicast only within its VLAN” at the hospital wing, this would power a supported endpoint over its Ethernet connection without a local adapter instead: the switch PoE subsystem supplies negotiated electrical power within the model's available budget. At the hospital wing, the operational proof would instead be to clear a learned destination and observe initial flooding only to permitted VLAN members, whereas “Allocate PoE power to a camera port” is validated by a different test: check delivered watts, endpoint PoE class and remaining switch power budget.

C:

Compared with the requested “Flood unknown unicast only within its VLAN” at the hospital wing, this would give the switch a manually controlled next hop for a known remote prefix instead: a static route adds an operator-defined forwarding path subject to route selection and reachability. At the hospital wing, the operational proof would instead be to clear a learned destination and observe initial flooding only to permitted VLAN members, whereas “Install a static route” is validated by a different test: inspect the routing table for the route prefix, next hop and selected forwarding entry.

D:

For the hospital wing, “Enable DHCP relay on an SVI” is a different type of control from “Flood unknown unicast only within its VLAN”: a relay forwards DHCP requests to a configured remote server rather than offering its own address pool. Unlike the requested feature, that setting addresses the need to allow clients in one VLAN to reach a DHCP server in a different IP subnet, not the objective to deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary.

Question 148

When engineers flood unknown unicast only within its VLAN at the training center, which forwarding, security, management or diagnostic outcome follows from that action?

  1. OSPF forms neighbor relationships and advertises reachable prefixes within configured areas
  2. The switch learns IGMP group membership and forwards multicast to interested ports
  3. A static route adds an operator-defined forwarding path subject to route selection and reachability
  4. The switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN
  5. Unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain

Explanation

Correct Answer

E:

The relevant mechanism is: the configured operation is meant to deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary. The most relevant validation is to clear a learned destination and observe initial flooding only to permitted VLAN members for the equipment at the training center.

Incorrect Answers

A:

This outcome would be relevant to “Enable OSPF adjacency on routed interfaces” at the training center, not the task “Flood unknown unicast only within its VLAN”; the other task is to exchange dynamic route information with neighboring Layer 3 devices. The action “Flood unknown unicast only within its VLAN” targets a different result: unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain; the proposed alternative would instead be checked by check OSPF neighbor state and learned routes for the intended area.

B:

That behavior applies when engineers “Enable IGMP snooping for multicast VLANs”; the different operation “Flood unknown unicast only within its VLAN” is intended to deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary. That different feature is verified by inspect multicast-group memberships and listener-facing interfaces; for “Flood unknown unicast only within its VLAN” on an access switch in routine maintenance, the relevant evidence is to clear a learned destination and observe initial flooding only to permitted VLAN members.

C:

That behavior applies when engineers “Install a static route”; the different operation “Flood unknown unicast only within its VLAN” is intended to deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary. That different feature is verified by inspect the routing table for the route prefix, next hop and selected forwarding entry; for “Flood unknown unicast only within its VLAN” on an access switch in routine maintenance, the relevant evidence is to clear a learned destination and observe initial flooding only to permitted VLAN members.

D:

That behavior applies when engineers “Learn source MAC addresses per VLAN”; the different operation “Flood unknown unicast only within its VLAN” is intended to deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary. That different feature is verified by inspect the learned MAC table for VLAN and ingress-port association; for “Flood unknown unicast only within its VLAN” on an access switch in routine maintenance, the relevant evidence is to clear a learned destination and observe initial flooding only to permitted VLAN members.

Question 149

A feature acceptance test on a managed campus switch concerns “Flood unknown unicast only within its VLAN.” What should be checked to establish its expected operation?

  1. Check VRRP master state and failover behavior for the virtual gateway
  2. Clear a learned destination and observe initial flooding only to permitted VLAN members
  3. Capture the broadcast on another member of the same VLAN but not on a different VLAN
  4. Inspect BGP neighbor session state and the prefix received from the remote autonomous system

Explanation

Correct Answer

B:

This approach fits because unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain. Directly measuring that result demonstrates whether the step to deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary succeeded on a managed campus switch.

Incorrect Answers

A:

This check is suited to “Configure VRRP on routed interfaces” when trying to provide a shared default-gateway address resilient to one router failing, not to verify “Flood unknown unicast only within its VLAN” at the lab. Checking “Flood unknown unicast only within its VLAN” at the lab requires evidence of its own mechanism: unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain; that is not the outcome measured by “Configure VRRP on routed interfaces”.

C:

The proposed check concerns “Replicate Ethernet broadcast within a broadcast domain” rather than “Flood unknown unicast only within its VLAN”: broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port. For “Flood unknown unicast only within its VLAN” on a managed campus switch, a better test would be to clear a learned destination and observe initial flooding only to permitted VLAN members, which targets deliver traffic whose destination MAC is not yet learned without crossing a VLAN boundary rather than the alternative diagnostic “Replicate Ethernet broadcast within a broadcast domain”.

D:

This check is suited to “Establish BGP peering for prefix exchange” when trying to exchange policy-controlled routing information with an external routing peer, not to verify “Flood unknown unicast only within its VLAN” at the lab. Checking “Flood unknown unicast only within its VLAN” at the lab requires evidence of its own mechanism: unknown-destination Layer 2 frames are flooded to eligible ports in their broadcast domain; that is not the outcome measured by “Establish BGP peering for prefix exchange”.

Question 150

During a change window in the media studio, engineers are asked to reach all eligible peers for a local Layer 2 discovery request. What should they configure rather than using a feature for an adjacent purpose?

  1. Replicate Ethernet broadcast within a broadcast domain
  2. Learn source MAC addresses per VLAN
  3. Enable IGMP snooping for multicast VLANs
  4. Enable OSPF adjacency on routed interfaces

Explanation

Correct Answer

A:

The critical distinction is that broadcast frames are replicated on suitable ports within the ingress VLAN, excluding the incoming port. The operator can test this claim by the specific check: capture the broadcast on another member of the same VLAN but not on a different VLAN.

Incorrect Answers

B:

Compared with the requested “Replicate Ethernet broadcast within a broadcast domain” at the media studio, this would forward future unicast traffic efficiently to a known endpoint instead: the switch updates its Layer 2 forwarding table from received source addresses in the relevant VLAN. At the media studio, the operational proof would instead be to capture the broadcast on another member of the same VLAN but not on a different VLAN, whereas “Learn source MAC addresses per VLAN” is validated by a different test: inspect the learned MAC table for VLAN and ingress-port association.

C:

For the media studio, “Enable IGMP snooping for multicast VLANs” is a different type of control from “Replicate Ethernet broadcast within a broadcast domain”: the switch learns IGMP group membership and forwards multicast to interested ports. Unlike the requested feature, that setting addresses the need to avoid flooding subscribed multicast traffic to every access port, not the objective to reach all eligible peers for a local Layer 2 discovery request.

D:

Compared with the requested “Replicate Ethernet broadcast within a broadcast domain” at the media studio, this would exchange dynamic route information with neighboring Layer 3 devices instead: OSPF forms neighbor relationships and advertises reachable prefixes within configured areas. At the media studio, the operational proof would instead be to capture the broadcast on another member of the same VLAN but not on a different VLAN, whereas “Enable OSPF adjacency on routed interfaces” is validated by a different test: check OSPF neighbor state and learned routes for the intended area.

Fortinet NSE 5 - FortiSwitch 7.6 Administrator (NSE5_FSW_AD-7.6) Practice Tests